Business Telephone Caller ID AT-50P USER GUIDE GVT-090879-001 Issue 1.0 January, 2019...
IMPORTANT NOTICE IMPORTANT NOTICE Liability Disclaimer NEC Corporation reserves the right to change the specifications, functions, or features, at any time, without notice. NEC Corporation has prepared this document for use by its employees and customers. The information contained herein is the property of NEC Corporation and shall not be reproduced without prior written approval from NEC Corporation.
IMPORTANT NOTICE SAFETY INSTRUCTIONS When using this telephone, basic safety precautions should always be taken to reduce the risk of fire, electric shock, and injury to persons, by doing the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3.
TABLE OF CONTENTS IMPORTANT NOTICE ......................i FACE LAYOUT, KEY AND PARTS ..................1 INSTALLATION ........................3 Connecting the Telephone Network ..................... 3 Wall Mounting ..........................3 INITIAL SETUP ........................5 Setting the Calendar ........................5 Setting the LCD Contrast ......................5 Selecting the Ringing Volume ......................
FACE LAYOUT, KEY AND PARTS FACE LAYOUT, KEY AND PARTS The following figures show the locations of key and parts of telephone.
FACE LAYOUT, KEY AND PARTS Name Function Call Indicator/ Flashes to indicate an incoming call arrival. Also, indicate when Message Waiting Lamp messages have been received and notified by PBX system control. LCD Display Shows calendar and various information. Search Key Select IN /OUT history and scroll the call record.
INSTALLATION INSTALLATION Connecting the Telephone Network Connect the telephone to the telephone network with following steps. Connect the one end of the line cord to the LINE socket on the rear of telephone and the other end to your telephone network outlet. Lay the handset cord in the groove on the bottom of the telephone.
INSTALLATION Remove the hanger hook from the telephone, and then reverse it and reinsert to the telephone. Pull up Reverse and Pull down If you wish to temporarily place the handset down during a conversation, hook the handset onto the top of the hanger hook as shown below.
INITIAL SETUP INITIAL SETUP Setting the Calendar This telephone is equipped with a calendar showing Year/Month/Day/Hour/Minute. The calendar is shown on the display while the phone is idle. Set the calendar with the following steps. NOTE When the telephone receives an incoming call the time and date will automatically be overwritten with the system time and date.
INITIAL SETUP Selecting the Dialing Mode Set the Dialing Mode Switch on the rear of the telephone to either DP (Pulse) or MF (Tone) to select the signaling type. The signaling type depends on the requirements of the PBX to which the telephone is connected.
BASIC OPERATION BASIC OPERATION Making a Call using the Handset Pick up the handset and wait for dial tone. Dial the desired number. Replace the handset when you finish the call. Or, to preview the dialed number: Dial the desired number with handset on-hook. You may press the DELETE key to erase dialed digits one at a time.
FEATURES FEATURES FLASH Key The FLASH key works the same as the hook switch of the phone. When the FLASH key is pressed during a conversation, it may terminate the call or place the call on hold and you will hear dial tone allowing you to dial the next phone number.
FEATURES Microphone Mute The MUTE key allows you to switch off the handset temporarily. During this state, you can consult with another person and your voice will not be sent to the called party. To mute the call so that the called party cannot hear you: Press the MUTE key.
FEATURES Caller ID (CID) This telephone will display Caller ID (CID) information received with incoming calls. The last 30 Caller ID numbers received are automatically stored in CID memory (up to 21 digits each). The numbers stored in CID memory may be reviewed, deleted, or dialed back if desired. When a new call is received with CID and goes unanswered, the NEW icon will flash.
TROUBLESHOOTING TROUBLESHOOTING Troubleshooting Guide Problem Solution Check that the hook switch is not depressed. Check that the line cord is connected. No dial tone /Will not dial out Ensure that the Dialing Mode Switch is set to the correct position. ...
SPECIFICATIONS SPECIFICATIONS Item Specifications Exterior Dimensions (W × D × H) 148×219×77mm / 5.83×8.62×3.03 inch Weight Approx. 0.56 kg /1.24 lbs Operating Conditions 0～40 ℃ / 32～104 °Ｆ Operating Temperature Relative Humidity 10～90% RH（Non-condensing） Functions Caller ID receiver FSK (type I) Caller ID information CID number with date and time stamp Caller ID review, delete, dial back...
QUICK REFERENCE Stored Data Function Contents of Data Ring Tone 1: Low Tone (default) 2: Mid Tone 3: High Tone PBX Trunk Access Code 0~9 (default = not assigned) Hook Flash Timing 00: 95ms 01: 100ms Feature Access Code settings 02: 120ms 03: 180ms 04: 270ms...
Caller ID Business Telephone AT-50P USER GUIDE GVT-090879-001 January, 2019 Issue 1.0 NEC Corporation...