Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CleanFreak 225BUCF
Summary of Contents for CleanFreak 225BUCF
- Page 1 Floor Burnisher 225BUCF Operator’s Manual...
- Page 2 FOR YOUR SAFETY DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Record This Important Information Date of Purchase Purchased From Address City State Phone Contact Machine Model Machine Serial Number Important Phone Numbers Medical Emergency...
-
Page 3: Table Of Contents
Table of Contents Safety Precautions..............4 How to Operate the Machine..........9 Technical Specifications............5 Installing / Replacing a Pad.........9 Operator Responsibility............6 Operation............10 Machine Preparation............6 After Use...............10 Unpacking the Machine..........6 Scheduled Maintenance...........11 Transporting the Machine........6 Machine Troubleshooting..........11 Grounding Instructions..........7 Electrical Schematic............12 Extension Cords.............7 Parts Manual..............14 Machine Components............8 Manufacturer’s Warranty...........18... -
Page 4: Safety Precautions
DO NOT use the machine DO NOT make unauthorized modifications or alterations if it is not in proper operating condition, and report to this machine. CleanFreak assumes no liabilities any damage or operation faults immediately. for injury or damage resulting from an unauthorized modification or alteration to the machine. -
Page 5: Technical Specifications
Technical Specifications: Description 225BU20CF Voltage (V) Frequency (Hz) Current (A) Pad / Brush Speed 1500 rpm Power 1.5 hp (1.1 kW) Pad Size 20” (51 cm) Cord 14/3 Yellow Cord Length 50’ (15 m) Height w/ Handle 49” (125 cm) Width 20”... -
Page 6: Operator Responsibility
Commercial use only. Figure 1 This machine is designed and manufactured for indoor use on hard floor surfaces. CleanFreak does not recommend use of this machine in any environment other than an indoor environment. This floor machine is designed and manufactured for commercial floor use only. -
Page 7: Grounding Instructions
Grounding Instructions WARNING: To prevent possible electric shock, protect the machine from rain. Keep the machine in a dry building. 120 Volt Machines WARNING: To prevent possible electric shock, always This product must be grounded while in use to protect use a 3-wire electrical system connected to the electrical the operator from electrical shock. -
Page 8: Machine Components
Machine Components Operator Handle Grips Switch Lever Switch Levers Safety Lock Cord Hook Handle Release Lever Power Cord... -
Page 9: Operator Handle Grips
How to Operate the Machine Operator Handle Grips Use the operator handle grips to operate and move Installing the Pad the machine. The switch levers on the underside of CAUTION! Using the wrong pad on this machine the handle grips, turn the motor on and off. Locate the can overload the motor. -
Page 10: Operation
Operation After Use 1. Place the operators handle (4) in the upright (vertical) 1. Unwrap the power cord and plug it into the properly position and unplug the power cord. Wrap the power grounded outlet. cord around the operator hand grips (1) and the cord 2. -
Page 11: Scheduled Maintenance
Hold in the switch lever safety lock and then engage switch levers. Bad connection Check the motor and cord interlock connections. Contact CleanFreak.com Defective motor start switch Contact an authorized APEC Distributor. Using extension cord with wire smaller than 12/3. Replace with a 12/3 extension cord. -
Page 12: Electrical Schematic
Electrical Schematic - 120V... -
Page 14: Parts Manual
Main Assembly REPLACE EXISTING RF065200 WITH THIS VERSION AND VERIFY ALL PARTS ON PARTS LIST ARE UPDATED. (PAGE 14 AND 15) RF065200 021017... - Page 15 Main Assembly Parts List ITEM PART NUMBER DESCRIPTION 39857A WHEEL 5 POLISHER MP236800 KEY, 3/16 X 1 7/8 56109699 CAM ASSY WITH GRIP 920342 NUT LK 3/8 -16 REG 980349 WASHER WEAR CAM NB3265 NUT, LOCK, 5/16"-18, NC NB6110 WASHER, LOCK, 1/4" NB3350 WASHER, FLAT, 1/4"...
- Page 16 Handle Assembly RF065300 11/29/16...
- Page 17 Handle Assembly (continued) Item Ref. No. Description Item Ref. No. Description 61373A HANDLE TUBE MP476300 CORD, POWER, 14/3 , YELLOW 40789A CORD INTERCONNECT 80284A SCREW, 10-32 UNF X .75 21075A HANDLE, REAR - CFP MP523100 DECAL, HANDLE MP504200 HOUSING, BEARING, SPINDLE, 50781A CLAMP HANDLE C2K FRONT...
-
Page 18: Manufacturer's Warranty
CleanFreak. applicable period stated above. (3) This warranty extends to the original purchaser (2) Warranty repairs will be made by CleanFreak or by only and is not transferable to subsequent owners. a service center of its choosing. TIME PERIODS... - Page 20 CleanFreak 3900 N. Providence Rd Appleton, WI 54913 www.cleanfreak.com 1-888-722-5508 1-920-882-8453 LT077400...
Need help?
Do you have a question about the 225BUCF and is the answer not in the manual?
Questions and answers