Assembly And Adjustments - DeWalt DWH161 Manual

Intended Use
Your DWH161 cordless dust extractor can be used for mobile
operation to take up dry, non-combustable dusts. Only for
indoor use.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
DO nOT pick up materials that present a risk of explosion,
glowing or burning materials, flammable materials, gases or
other hazardous substances.
nOTE: This appliance is suited for professional and commercial
use, e.g. in hotels, schools, hospitals, factories, shops, offices,
rental companies, and on construction sites.
• This machine is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge.
• Children should be supervised to ensure that they do not
play with the appliance.
D WALT Bluetooth® Tool Tag Ready (Fig. H)
e
Optional Accessory

WARNING: Read instruction manual for the D
Bluetooth® Tool Tag.

WARNING: Turn dust extractor off and disconnect battery
pack before installing the D

WARNING: When installing or replacing the D
Bluetooth® Tool Tag, use only the screws provided. Be sure
to securely tighten the screws.
Your dust extractor comes with mounting holes
installing a D WALT Bluetooth® Tool Tag (DCE041). Use only the
e
original fasteners included with the tool tag. You will need a T15
(Torx) bit tip to install the tag. The D
for tracking and locating professional power tools, equipment,
and machines using the D
e
installation of the D WALT Tool Tag refer to the D
e
Tag manual.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Dust Extractor (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Dust Extractor
1. Align the battery pack
1
extractor (Fig. B).
2. Slide the battery pack in until it is firmly seated in the dust
extractor and ensure that you hear the lock snap into place.
WALT
e
WALT Bluetooth® Tool Tag.
e
WALT
e
17 for
WALT Tool Tag is designed
e
WALT Tool Connect™ app. For proper
WALT Tool
e
WALT battery packs and chargers.
e
is fully charged.
1
with the rails inside the dust
To Remove the Battery Pack from the Tool
1. Press the release button
out of the dust extractor.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 15 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Attaching the Carry Strap (Fig. C)
Your dust extraction system comes with a carry strap
can be connected to the carry strap hooks
as shown in Fig. C.
Attaching the Crevice Tool (Fig. A)
• To attach the crevice tool
insert the end of the dust extractor hose into the open end
of the accessory with a twisting motion until tight.
nOTE: The dust extraction hose is not compatible with
AirLock® connectors.
• To remove the crevice tool, hold the dust extraction hose
and pull the accessory off using a twisting motion.
Installing the Belt Hook (Fig. H)

WARNING: To reduce the risk of serious personal
injury, turn the dust extractor off and disconnect
battery pack before making any adjustments or
removing/installing attachments or accessories. An
accidental start-up can cause injury.

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the dust
extractor from a work belt. DO NOT use the belt hook
for tethering or securing the dust extractor to a person
or object during use. DO NOT suspend dust extractor
overhead or suspend objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook
use only the screw that is provided. Be sure to securely
13
tighten the screw.
If the hook is not desired at all, it can be removed from the
dust extractor.
English
2 and firmly pull the battery pack
10
11 in either manner
12 to the dust extractor hose
that
6 ,
18 ,
9