Download Print this page

Mercia Garden Products Groundsman General Instructions Manual

Advertisement

Quick Links

General Instructions
01GRO1008DD-V3
10x8 Groundsman
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
- Check the pack and make sure you have all the parts listed.
- When you are ready to start, make sure you have the right tools at hand (not supplied)
including a Phillips screwdriver, Stanley knife, wood saw, step ladder and drill with 2mm
bit.
- Ensure there is plenty of space and a clean dry area for assembly.
TIMBER
As with all natural materials, timber can be affected during various weather conditions.
For the duration of heavy or extended periods of rain, swelling of the wood panels may
occur. Warping of the wood may also occur during excessive dry spells due to an interior
moisture loss. Unfortunately, these processes cannot be avoided but can be helped. It is
suggested that the outdoor building is sprayed with water during extended periods of
warm sunshine and sheltered as much as possible during rain or snow.
Our buildings are pre treated with a water based treatment**; this only helps to protect
the product during transit and for upto 3 months against mould. To validate your
guarantee and ensure longevity of the product, it is ESSENTIAL the building is treated
with a wood preserver within the first three months of assembly and thereafter in
accordance with the manufactures recommendations. Care must be taken to ensure
the product is placed on a suitable base.
BUILDING A BASE
When thinking about where the building and base is going to be constructed:
Ensure that there will be access to all sides for maintenance work and annual
treatment.
Ensure the base is level and is built on firm ground, to prevent distortion. Refer to
diagrams for the base dimensions, The base should be slightly smaller than the external
measurement of the building, i.e. The cladding should overlap the base, creating a run
off for water. It is also recommended that the floor be at least 25mm above the
surrounding ground level to avoid flooding.
TYPES OF BASE
- Concrete 75mm laid on top of 75mm hard-core.
- Slabs laid on 50mm of sharp sand.
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instruction pages for your specific product code
Please retain product label and instructions for future reference
All building's should be
x2
erected by two adults
For ease of assembly, you
MUST pilot drill all screw
holes and ensure all screw
heads are countersunk.
2mm Drill bit
**Protim Aquatan T5 (621)**
Your building has been treated with Aquatan.
Aquatan is a water-based concentrate which is diluted with water, the building as been treated by the correct
application of Aquatan solution and then allowed to dry.
Aquatan is a decorative finish to colour the wood, which is applied industrially to timber fence panels and
garden buildings.
Aquatan undiluted contains: boric acid, sodium hydroxide 32% solution, aqueos mixture of sodium dioctyl
sulphosuccinat and alcohols: 2, 4, 6-trichlorophenol.
For assistance please contact customer care on: 01636 880514
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
Winter = High Moisture = Expansion
Summer = Low Moisture = Contraction
CAUTION
Every effort has been made during the
manufacturing process to eliminate the
prospect of splinters on rough surfaces of the
timber. You are strongly advised to wear gloves
when working with or handling rough sawn
timber.
P 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Groundsman and is the answer not in the manual?

Questions and answers

Summary of Contents for Mercia Garden Products Groundsman

  • Page 1 For assistance please contact customer care on: 01636 880514 - Concrete 75mm laid on top of 75mm hard-core. - Slabs laid on 50mm of sharp sand. Mercia Garden Products Limited, Sutton On Trent, Whilst all products manufactured are made to the highest standards of Safety and in...
  • Page 2 01GRO1008DD-V3 Please retain product label and instructions for future reference Overall Dimensions: Length = 3147mm Width = 1969mm Height = 2094mm Base Dimensions: Butt Hinge Hasp & Staple T-Hinge Tower Bolt Casement Stay “L” Bracket Length = 3044mm Bolt Block PI-07-0066 PI-07-0191 PI-07-0021...
  • Page 3 Please retain product label and instructions for future reference Step 2 Step 4 Place the floor panels Using the same method outlined in Step 3, fix the plain sides & the onto a firm & level base, ensure the base has door gable using 12x50mm screws.
  • Page 4 Please retain product label and instructions for future reference Step 6 Step 8 Now That the roof is fixed Attach the cover trims to the secure the building to the building using 3x40mm floor with 24x50mm screws. screws per strip. * Ensure to screw in alignment 18x40mm Screws with the floor bearers.
  • Page 5 Please retain product label and instructions for future reference Step 10 Step 12 To fix the lock in place. Screw the Staple Opening Window to the Door Gable or Slave door. Place the window strip 11mm over the window opening and Making sure the Hasp is in line with fix in place with 3x30mm the staple and screw into the Door or...
  • Page 6: After Treatment

    Please retain product label and instructions for future reference Step 13 Fix the casement stay to the window and then align the fixings to the window panel framing. Ensure the casement stay fits onto the fixings when closed before securing in place.

This manual is also suitable for:

01gro1008dd-v3