Viking K-1900-812L-IP Product Manual page 16

18. Relay 1 or 2 Act (Activation) Command
The one or two digit code stored in the Relay Activation Command is the touch tone command that the person being
called must enter on their phone in order to momentarily activate relay 1 or 2 to control a doorstrike, mag-lock, gate
controller, or other device. The code can contain the characters 0 - 9, 00 - 99, ## or ,,. The code cannot match a
relay latching or toggle command (11, 10, 1#, 21, 20, or 2#). The code must be entered while the remote phone is
communicating with the Entry phone. The Entry phone determines which direction the touch tone is coming from and
only responds to touch tones from the called phone. Factory Setting: Relay 1 - ,,, Relay 2 - ,2
19. Relay 1 or 2 Activation Time
The value stored in the Relay 1 or 2 Activation Time is the amount of time relay 1 or 2 will be energized after a correct
momentary touch tone command is entered, "#" plus a valid keyless entry code or a proximity card was scanned that
is programmed to momentarily activate the relay. This number can range from 0.5 to 99 seconds. Note: This also
affects timing in Doorbell Mode. Factory Setting: 5 seconds
20. Relay Activation Delay
A relay activation delay of 0.5 - 99 seconds can be programmed in the K-1900-8-IP Series phone. A relay activation
delay is useful in two door vestibule entrance applications. This allows you to program a delay time from when relay 1
(outside door) is activated to when relay 2 (inside door) is activated. The programmed delay time should be set to the
average time it takes a person to walk from the outside door to the inside door.
When a request for exit (REX) is activated, relay 2 will activate first, then after the programmed delay relay 1 will
activate. Factory Setting: Disabled
21. Relay Latch Commands
When set to "Enabled" the Remote Access Operation Commands to Un-Latch
When set to "Disable" the Remote Access Operation Commands to Un-Latch
Disabling the Latch commands can be useful in applications where you want to eliminate the possibility of inadvertently
entering a latch command leaving a gate open/closed, etc. The relays can still be activated with the "Relay Activation
Command" for momentary closures.
22. In-Band Audio Call Progress
The In-Band Audio Call Progress Detection can be set to enabled or disabled. In-Band Audio Call Progress detection
should be enabled in applications where you are making an outbound call through your VoIP phone system and are
relying on In-Band analog audio for ringback or busy detection. Factory Setting: E nabled
23. In-Band Audio Detect Sensitivity
The In-Band Audio Detect level (Sensitivity) can be set from 1 - 9, 1 = minimum setting, 9 = highest setting. Increasing
or decreasing the sensitivity may be required in applications where you are making an outbound call through your VoIP
phone system and are relying on In-Band analog audio detection. Power cycle unit after changing this setting.
Factory Setting: 5
24. Handset Default Volume
The Handset Default Volume can be set from 1 to 4, 1 = lowest volume setting, 4 = highest volume setting. This will be the
default volume setting from off hook but then can be increased or decreased with the handset volume control button. Setting
it to "1, 2, 3, or 4 only" will lock the volume at that setting for all calls (handset volume control button disabled). Setting it to
"last used" will leave the handset volume set to the last user adjusted volume setting.
Factory Setting: 1
25. Phone Mode
The Phone Mode can be programmed to one of two settings: Auto Dialer or Manual Dial Phone. When set to Auto
Dialer the K-1900-8-IP will auto dial any preprogrammed phone numbers stored in the Phone Number Database when
the corresponding Speed Dial Number (example: apartment number) is entered on the unit's keypad. When set to
Manual Dial Phone the unit's auto dialing features are disabled and the unit functions as a standard VoIP phone. When
the handset of the K-1900-8-IP is lifted, dial tone is provided and the user can manually dial the desired number on the
keypad. Keyless entry codes can be used in either mode. Factory Setting: Auto Dialer
Factory Setting: Enabled
16
, Latch or Toggle the relay are enabled.
, Latch or Toggle the relay are disabled.