Advertisement
Quick Links
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE! IF
YOU DO NOT UNDERSTAND THE INSTRUCTIONS, OR DO NOT FEEL THAT YOU CAN FOLLOW
THEM SAFELY, CONTACT A QUALIFIED CONTRACTOR. THE WARRANTY WILL BE HONOURED IF
ACCOMPANIED BY AN ORIGINAL SALES RECEIPT, AND ONLY IF THE INSTRUCTIONS HAVE
BEEN FOLLOWED EXACTLY.
・ The HVAWM3260S is designed to mount a panel onto a vertical wall. Hardware for mounting to
a wood stud is included. For mounting to any other surface, it is recommended you contact a
qualified contractor.
・ The wall or mounting surface must be capable of supporting the combined weight of the mount
and the display, otherwise the structure must be reinforced.
・ Safety gear and proper tools must be used. A minimum of two people are required for this installation.
Failure to use safety gear and/or attempting this installation alone can result in property damage,
serious injury, or death.
・ Follow all instructions and recommendations regarding adequate ventilation and suitable locations for
mounting your flat panel. Consult the owner ' s manual for your flat pane
・ This product will hold flat panels up to 60" and weighing up to 150 l . s
・ VESA 200mm x 200mm-600mmx400mm.
Tools Required
・ Stud finder ("edge to edge" stud finder is r
・ Phillips scre
w
r d
v i
・ Penc l i
・ Ham
m
r e
D
r
l l i
C (
o
・ 1/
" 4
r d
l l i
i b
f t
r o
w
・ 7/16"
o s
k c
t e
w
e r
n
・ L
e
v
l e
・ Tape measure
B
A
M5*15mm
M5*25mm
(x4)
(x4)
I
Metal Washer
φ8mm (x4)
1
HVAWM3260S
r e
n
r c
t e
i e
s n
a t
l l
t a
o i
n
o
l n
o
o
d
s
u t
s d
3 ,
8 /
"
r d
l l i
c
h
r o
b
t i
r d
v i
e
f r
r o
w
Wall Plate (x1)
C
D
M6*25mm
M6*12mm
(x4)
(x8)
J
Spacers (x4)
INSTRUCTIONS
c e
o
m
m
e
n
d
e
) d
) y
i b
f t
r o
c
o
n
c
e r
e t
o
o
d
c s
e r
w
s
Parts List
Adaptor Plate (x1)
E
F
M8*15mm
M8*12mm
(x4)
(x4)
K
Slider Plates
Allen Key (x1)
(x4)
f l
r o
m
r o
i e
b
Adaptor Brackets (x2)
G
M8*30mm
(x4)
M
L
Lag Bolt
8*70mm (x4)
f n
r o
m
t a
o i
. n
H
Metal Washer
φ6mm (x8)
N
Anchor (x4)
Advertisement
Related Manuals for Displays2go HVAWM3260S
Summary of Contents for Displays2go HVAWM3260S
- Page 1 ACCOMPANIED BY AN ORIGINAL SALES RECEIPT, AND ONLY IF THE INSTRUCTIONS HAVE BEEN FOLLOWED EXACTLY. ・ The HVAWM3260S is designed to mount a panel onto a vertical wall. Hardware for mounting to a wood stud is included. For mounting to any other surface, it is recommended you contact a qualified contractor.
- Page 2 Step 1A - Mounting the wall plate to wooden studs (Fig. 1) The HVAWM3260S can be mounted onto two wooden studs, with center to center distances between 16" (406mm). Using an electronic stud finder, locate the center of the two wooden studs at the desired mounting location.
- Page 3 Fig. 3 Step 2 - Assembling the Adaptor Plate (Fig.3) Adaptor rail Insert slider plates (x4) into the adaptor rails, then Adaptor bracket insert the adaptor brackets into the adaptor rails. Slider plate Attach the adaptor bracket and slider plates with four M6*12mm screws and four 6mm metal washers φ...
- Page 4 Step 5 - Adjusting the flat panel Fig. 7.1 The HVAWM3260S provides a wide range of adjustment possibilities to suit your environment. Roll Control - Horizontal levelling of the flat panel display. Grasp the edge of the panel and roll it up or down into a level Fig.
- Page 5 Fig. 15 Maintaining the HVAWM3260S The arm assembly and wall plate may be cleaned with a soft sponge and mild solution of soap and water. Caution : Be sure not to get moisture on the electrical connections or the panel.
Need help?
Do you have a question about the HVAWM3260S and is the answer not in the manual?
Questions and answers