Extension Wand; Start Operation - Panasonic MC-CJ915 Operating Instructions Manual

Please read the safety instructions (P.3) before using this cleaner.
ENGLISH
CAUTIONS
The plug must be removed from the socket outlet before cleaning or maintaining the appliance.
●
DO NOT use hot air or hot surface to dry the fi lter. Dry it at room temperature for approximately 24 hours.
●
IMPORTANT: Before re-installing the washable fi lter, make sure it is completely dry to avoid damaging the appliance.
●
DO NOT use the telescopic wand or the extension wand when using the blower operation. Wand will get hot.
●
First, assemble the parts together.
Parts are set surely so as not to come off.
• •
MC-CJ919 MC-CJ917
Connect the edge of the hose and the upper end of the telescopic wand
by inserting one into the other and twisting together.
Attach the fl oor nozzle to the other end
while aligning the raised section with the hole.
(When removing them , push the tab down while
pulling on the telescopic wand.)
• •
MC-CJ913 MC-CJ911
Insert the hose unit into the upper end of the telescopic wand or
the extension wand, and the fl oor nozzle to the other end.
Alternative nozzles
Crevice nozzle:
For narrow gaps, etc.
Dusting brush:
For furniture,venetian
blinds, etc.
2
Adjust the nozzle
to suit the fl oor
•
MC-CJ919
•
MC-CJ917
•
MC-CJ915
Parquet /
Bare fl oor
Carpet
Carpet
Cord rewind pedal
Press the
not the edge of
the pedal.
Blower
How to use Blower
For locations where the nozzle will not enter,
connect the hose to the blower and blow the dust out.
Step 1 Step 2
Turn off the appliance, Turn on the appliance and
release the connection blow the dust out.
pipe from hose inlet.
Connect the hose to
the blower.
Connection pipe
4
•
MC-CJ915

Extension wand

•
MC-CJ911
Connect the two extension
wands by inserting one
into the other and twisting
together.
Parquet /
Bare fl oor
•
MC-CJ913
•
MC-CJ911
mark,
Floor nozzle
(Durable 2-step nozzle)
•
MC-CJ911
Telescopic wand
•
MC-CJ919
•
MC-CJ917
•
MC-CJ915
•
MC-CJ913
Length may be
adjusted.
Release
pedal
Release pedal
Floor nozzle
(3D EZ Nozzle)
• •
MC-CJ913 MC-CJ919
•
MC-CJ917
•
MC-CJ915
Step 3
Turn off the appliance,
connect the connection
pipe to the hose inlet.
After this, turn on the
appliance and clean the
dust.
Hose inlet
1

Start operation

Press
Press the mark, not
the edge of the pedal.
To increase or decrease the power,
slide the variable power control .
Suction regulator
Use when strong
suction causes the
nozzle to stick to the
fl oor, hindering
movement.
Hose
Variable
Power
control
Dust cover
Cloth dust bag
(in body)
Dust indicator
Turn the power control to the highest setting
and lift the nozzle off the fl oor.
If the dust indicator turns red, the cloth dust bag
is full and requires replacing the cloth dust bag.
How to use 3D EZ Nozzle
(MC-CJ919)(MC-CJ917)(MC-CJ915)
Remove the floor nozzle by pressing the
release pedal and you can use EZ Crevice or
EZ Upholstery easily anytime.
EZ Crevice
For narrow gaps, etc.
Changing the
cleaning power.
Plug
Power
cord
ON/OFF Switch
pedal
EZ Upholstery
For sofa, etc.