TABLE OF CONTENTS PAGE PAGE 1 Specifications ------------------------------------------------------3 2 Location of Controls and Components--------------------4 3 Troubleshooting Guide------------------------------------------5 4 Disassembly and Assembly Instructions -----------------7 4.1. Disassembly of the Dust Cover Assy -----------------7 4.2. Disassembly of the Dust Bag Holder------------------8 4.3. Disassembly of Body Cover Assy, Switch Pedal, Cord Rewind Button------------------------------9 4.4.
3 Troubleshooting Guide CONDITION CHECKPOINT FIGURE CHECK METHOD REMEDY The Motor CORD REEL • Check the continuity at both • If there is no continuity, replace doesn’t rotate. UNIT ends of the Plug and both ends the Cord Reel Unit, or the Rail RAIL BASE of the Lead Wire Terminal of Base Unit.
Page 6
CONDITION CHECKPOINT FIGURE CHECK METHOD REMEDY ON/OFF • Check the continuity by press- • If there is a problem, replace SWITCH ing the On/Off Switch. the P.C.B. Assy. (in the P.C.B. Assy) 1. The Motor TRIAC (on the • Check that the Triac has not •...
4 Disassembly and Assembly Instructions Important: Always turn the vacuum cleaner is power off before replacing components. Remove the power cord and plug from the mains. * Attention (1) When disassembling the vacuum cleaner, check the connections and wiring (pulling) of each component, and ensure that everything is restored correctly once repairs are complete.
4.2. Disassembly of the Dust Bag Holder 1. Remove the Dust Bag Holder by inserting a slotted screwdriver into the mount of the Dust Bag Holder on the Lower Body Unit. Fig.2 Caution (There is a Spring inside) * When replacing the Dust Bag Holder, disassemble and replace the Spring mounted inside.
4.3. Disassembly of Body Cover Assy, Switch Pedal, Cord Rewind Button 1. Remove the Filter Case Fig.4 2. Remove 3 screws and disassemble the Body Cover Assy Fig.5...
3. Disassemble the Switch Pedal/Cord Rewind Button 4.4. Disassembly of Upper Body, toward the direction of the arrow Handle Cover, and Guide Lever Caution: (Spring is placed inside.) *Be careful not to lose the Spring. 1. Disassemble the Body Cover Assy and Switch Pedal as described in (4.3).
Page 11
3. Slide the Switch, and push it inward at the position 5. Disassembly of Handle Cover shown in the figure. Disassemble the Handle Cover from the Upper Body. Fig.11 6. Disassembly of Guide Lever Slide and disassemble the Guide Lever to the direc- Fig.9 tion of the arrow.
4.5. Disassembly of Motor Case Set 4.6. Disassembly of Cord Reel Unit 1. Disassemble the Rear Cover to the direction of the 1. Release the pretension of the Cord Reel Unit slowly arrow, and disassemble the Motor Case Set pulling by holding on the Power Plug and pressing on the upward.
Disassembly of Rail Base Unit 4.8. Disassembly of Fan Motor Unit 4.7. 1. Remove screw and disassemble the Rail Base Unit from 1. Disassemble the Swivel Cap and remove 3 screws. the Motor Case Set. Fig.18 Fig.16 2. Remove the tabs (4 positions) of the Motor Case Unit 2.
4.9. Disassembly of P.C.B. Assy 1. Disassembly of Volume (a part of P.C.B. Assy) Disassemble the Volume by widening the tab of the Motor Case Unit using a slotted screwdriver. Fig. 2. Disassemble the P.C.B. Holder by pressing on the 3.
4.10. Replacement of Blower Cover 1. Assemble the Spring (for Blower Cover) onto the Blower Cover Fig.25 2. Assemble by inserting the shaft of the Blower Cover into the boss hole. Fig.26...
6.4. PARTS LIST (BODY UNIT) Safety Ref. No. Service Parts No. Parts Name & Description Q’ty Remarks AMV93KB40R0J DUST COVER ASSY XTN4+20BFJ SCREW AMV0YAB40R0J BODY COVER ASSY AMV02GB6000J BODY LINING UPPER AMV06BB8020J HANDLE COVER AMV02AB80V0J UPPER BODY AMV75NB80V0J GUIDE LEVER AMV46NB80V0J CORD REWIND BUTTON (CORD REWIND PEDAL) AMV05EB80V0J SWITCH PEDAL...