Lincoln A Series User Manual page 3

13. Place the truck assembly on the floor. Place a container
drum containing the lubricant to be dispensed onto the
truck base. Center the drum on the base and adjust the
clamp assemblies close enough to the base of the drum
so that the set screws can be adjusted in to secure the
drum. They should also be far enough away from the
base of the drum, so that the drum can be removed by
loosening the set screws (item 26) only. Tighten the hex
screws (item 24) securely, 4-places.
14. Place the assembled follower (item 17) into the open
drum, on top of the lubricant, and push down on the fol-
lower until the lubricant flows slightly into the center open-
ing of the follower.
15. Place the pump tube, assembled with the drum cover, into
the drum by sliding the pump tube into the center hole
in the follower and sliding straight into the follower. The
pump tube should slide all the way into the drum until the
drum cover gasket rests on the top edge of the drum. The
follower (item 17) will remain on top of the grease, and will
move down with the lubricant as it is consumed, wiping
the pail walls clean, and moving the lubricant towards the
pump inlet.
16. Secure the drum cover to the drum with the three fillister
head screws (item 11) by tightening until the screws are
snug against the side of the drum.
17. Place the control valve grease coupler through the control
valve hanger (item 15) on the side of the drum cover for
convenient storage. The hose may be coiled around the
drum as desired.
18. Follow the priming instructions as detailed in the pump
operation manual, supplied with the pump.
Model 9917-57
See illustration #1 of this manual and follow assembly instruc-
tion steps 1 thru 11 and 14 thru 17. (Ignore steps 12 and 13.)
Model 9946P
See illustration #1 of this manual and follow assembly instruc-
tion steps 1 thru 11. Proceed to steps below.
12a. Assemble the dolly truck, item 30, as detailed in the dolly
truck assembly manual packaged with the dolly truck.
12b. Place the drum on the truck and secure per the instruc-
tions with the dolly truck.
Complete the assembly process by proceeding with steps 14
thru 17 above.
Form 403936
Models 9917, 9917-57, 9946P and 9989
High Pressure Lubrigun
Model 9989
Refer to illustration #4 of this manual.
1. Assemble the pail handle, item 23, to the pail cover, item
10, using four #10-24 x ½" R.H. machine screws, item 19,
mating lock washers (item 20), and nuts (item 21). As-
semble as shown in illustration #4. Tighten securely.
2. Insert snap button, item 31, into hole in cover opposite
handle.
3. Insert three thumb screws, item 12, loosely into pail cover,
as shown.
4. Assemble pump to pail cover by sliding the pump tube
through the bushing on the pail cover. Slide the cover up
to the pump outlet casting as far as it will go. Note that the
pump is not firmly attached to the cover, but is allowed to
pivot and float inside the cover
5. Note that hose adapter, item 8, has two different threads,
one finer than the other. Install the fine thread end of the
adapter into one end of the high pressure hose, item 22,
and tighten securely.
6. Install the course thread, ¼-18 NPT, of the adapter, item 8,
into the outlet of the pump and tighten securely.
7. The universal swivel, item 6, will have a similar fine thread
on one end as the adapter above. Assemble the fine
thread into the female opening on the opposite end of the
hose, item 22, and tighten securely.
8. Assemble the control valve per the instructions in Sec. F3,
Pg 2 series.
9. Attach the ¼-18 NPT male (course thread) into the control
valve, item 1 and tighten securely.
10. Attach the air nipple, item 4, to the air inlet of the pump,
item 3.
11. Attach the air coupler, item 5, to a 3/8" ID minimum air
hose. Do not apply air to the pump at this time.
12. Assemble the follower, item 18, per the instructions in
Sec. K5, Pg 6 Series. Place the assembled follower (item
18) into the open pail, on top of the lubricant, and push
down on the follower until the lubricant flows slightly into
the center opening of the follower.
13. Place the pump and pail cover over the pail, sliding the
pump tube into the opening in the center of the follower,
item 18. Secure the pail cover to the pail using the three
thumb screws, item 12, provided. The pump should slide
into the follower until it either rests on the bottom of the
pail or the pump outlet casting rests on the top of the
cover bushing. The pump will be free to rotate within the
pail cover. The follower, item 18, will remain on top of the
lubricant in the pail, and will move down with the lubricant
as it is consumed, wiping the pail walls clean, and moving
the lubricant towards the pump inlet.
14. Follow the priming instructions as detailed in the pump
operation manual, (Sec. A5, Pg 83 Series) supplied with
the pump.
Page Number - 3