Specifications - Lincoln A Series User Manual

Models 9917, 9917-57, 9946P and 9989
High Pressure Lubrigun
DESCRIPTION
Models 9917, 9917-57, 9946P, and 9989 are air operated
grease pumps designed to pump low and medium viscosity
materials, (grease) from drums and pails. They are high pres-
sure pumps that are capable of creating a maximum operat-
ing pressure of 5000 PSI with 100 PSI air. All models include
drum or pail covers, high pressure hose, control valve, grease
coupling, and universal follower.
Model 9917 is for use with 120# refinery containers and
includes a caster dolly base for portability. (Container drum
is not included.) Two high pressure swivels are included, one
straight swivel where the hose connects to the pump, and
a universal swivel for connection between the hose and the
control valve. (See front cover illustration.)
Model 9917-57 is the same as the 9917, above, but does not
include the caster dolly base. (See front cover illustration.)
Model 9946P is the same as the 9917, above, but includes
a 2-wheel dolly truck for portability instead of the caster dolly
base. (See front cover illustration.)
Model 9989 is for use with 35# refinery pails and includes a
pail cover with handle for portability. One universal swivel is
included for connection between the hose and control valve.
No dolly base or truck is included.

SPECIFICATIONS

Models 9917, 9917-57 and 9946P
Pump
Pump ratio
Pump Max. Working Pressure
Max. Air Pressure
Air Inlet
Lube Outlet (pump)
Hose
Model 9989
Pump
Pump ratio
Pump Max. Working Pressure
Max. Air Pressure
Air Inlet
Lube Outlet (pump)
Hose
For more specific information on pumps see appropriate
owner's manual for the pump.
Page Number - 2
©V350120000 (120# Pump)
50:1
5000 PSI [345 bar] (limited
by hose working pressure)
100 PSI [6.9 bar]
3/8 NPT (female) with
coupler
¼ NPT (female)
¼" ID x 7' SAE 100R2
high pressure hose
(5000 PSI [345 bar]
working pressure.
©V350035000 (35# Pump)
50:1
5000 PSI [345 bar] (limited
by hose working pressure)
100 PSI [6.9 bar]
3/8 NPT (female) with
coupler
¼ NPT (female)
¼" ID x 7' SAE 100R2
high pressure hose
(5000 PSI [345 bar]
working pressure.
ASSEMBLY INSTRUCTIONS
This pump can develop 7500 PSI working pressure at
150 PSI maximum incoming air pressure. Be sure that all
system equipment and accessories are rated to withstand
the maximum working pressure of this pump. Do not
exceed the maximum working pressure of the lowest rated
component in the system.
IMPORTANT: Accessory item 'Whip" hoses for dispens-
ing valve are rated 4500 PSI. DO NOT exceed 90 PSI air
pressure to pump when using 'Whip" hoses.
Model 9917
Refer to Illustration #1 in this manual
1. Assemble the control valve hanger (item 15) to the side
of the drum cover (item 9) using the two hex head screws
(item 16) and hex nuts (item 14) through the holes provided
in the cover.
2. Install the three fillister head screws (item 11) into the side
of the drum cover (item 9) as shown. Leave the screws
loose. They will be used later to secure the drum cover
onto the drum.
3. Assemble the pump to the drum cover with the four bolts,
item 13, supplied, as shown in the illustration. Tighten
securely.
4. Connect straight swivel (item 7) to pump outlet. (Note that
there are two different threads on the swivel. The ¼-18
NPT pipe thread will be a course thread compared with the
other thread.) Make sure to place the ¼-18 NPT male end
of the swivel into the ¼-18 NPT female outlet on the pump
body. Tighten securely.
5. Connect one end of the high pressure hose (item 22) to the
special (fine pitch) male thread on the straight swivel (item
7) and tighten securely.
6. Connect the remaining end of the high pressure hose to
the special male thread on the universal swivel (item 6) and
tighten securely.
7. Connect the ¼-18 NPT male thread on the universal swivel
(item 6) to the control valve (item 1) and tighten securely.
8. Install the grease coupling and extension tube into the out-
let end of the control valve, (item 1), and tighten securely.
9. Install the air nipple (item 4) into the air inlet of the pump
and tighten securely.
10. Attach the air coupler (item 5) onto a suitable 3/8" ID
(minimum) air hose and tighten securely. Do not apply air
pressure at this time.
11. Assemble the follower (item 17) per the instructions sup-
plied with the follower.
12. Assemble the truck assembly (item 29) as shown in il-
lustration #3. Leave the hex screws, item 24, and set
screws, item 26, loose until a container drum is placed on
the truck. Install the casters, item 28, into the sockets on
the bottom side of the truck base. They should snap into
place and not fall out when the truck is lifted from the floor.
© Indicates change
Form 403936