Bestway 65302 Owner's Manual

Owner's manual
Warning
IMPORTANT SAFETY INSTRUCTIONS
Read the manual and follow the instructions relating to safety tips, correct
and complete product assembly, setting into service, use and maintenance.
For your own safety, always heed the advice and warnings in these
instructions. Non-compliance with these operating instructions may expose
you to serious danger or death. Only use the product in the places and
conditions for which it is intended.
Stand-up Paddling is a dangerous sport. Use of this product exposes the
user to unexpected risks, dangers and hazards.
User should realize and understand these risks. The use of this product
implies the respect of the safety instructions described in the manual.
Do not exceed the maximum recommended number of persons.
Regardless of the number of persons on board, the total weight of persons
and equipment must never exceed the maximum recommended load.
Do not use this product if you are under the influence of alcohol, drugs or medications.
Life saving devices such as life jackets and buoys should be pre-inspected and used at all times. Always wear a helmet
when using this product.
Always paddle with an experienced partner when using this product.
Tell your sail routes and time schedule to your partner.
Check the weather forecast first to know the marine environment and weather conditions before starting. Bad weather
and marine environment is very dangerous.
Never use this product in conditions that are beyond your ability (such as, but not limited to, high surf, riptides, currents
or river rapids)
Use the product near the shore and beware of natural factors such as wind, tidewaters and tidal waves. BE AWARE OF
OFFSHORE WINDS AND CURRENTS.
Before every use, carefully inspect the product for signs of wear or leakage to ensure everything is in good condition.
Please do not use the SUP if you find any damage.
Do not surf in unfamiliar water areas.
Beware of potential harmful effects of liquids such as battery acid, oil and petrol. These liquids may damage the
product.
Inflate according to the rated pressure on the product or it will cause over inflation and/or an explosion.
Stay balanced. Uneven distribution of loads on the board may cause the board to overturn which could lead to
drowning.
Know how to operate this product. Check your local area for information and/or training as needed. Inform yourself
about local regulations and dangers related to surfing, boating and/or other water activities.
SAVE THESE INSTRUCTIONS
Technical Specifications
Item Inflated Size
65302 2.74m x 76cm x 12cm (9' x 30" x 4.75")
65304 3.05m x 84cm x 15cm (10' x 33" x 6")
#65302
001 002
008 009
#65304
001 002
010
Part No. Description
001 Surf Board
002 High Pressure Hand Pump
003 Oar
004 Footrest Tube
005 Footrest Foam
006 Safety Rope
007 Seat
008 Wrench
009 Polyester 3-ply patch
010 Bag
011 Air Valve
Elastic Cord
012
013 Fin
S-S-005745/21x28.5cm/加拿大规拉丝冲浪板说明书/65302; 65304/JS-YF-2016-B-14846/英
TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals Or
Spare Parts, Please Visit
www.bestwaycorp.com
Recommended Maximum Load Maximum Number
Working pressure Capacity of persons
1.034bar (15PSI) 95kg (209lb) 1 Adult
1.034bar (15PSI) 130kg (287lb) 1 Adult
003
006
010 011
006 008 009
011 012 013
SPARE PART SPARE PART
QTY
NO. (#65302) NO. (#65304)
1 65302CAASS18 65304CAASS18
1 P3055Q18 P3055Q18
1 F6C656 /
1 / /
1 / /
1 F6666 F6667
1 / /
1 F6H189 F6H189
1 / /
1 F6670 F6669
1 P6H971 P6H971
1 / F2C098
1 / F3C197
Installation
1. Spread out the surfboard on level ground.
2. Use your board at first time or after long period storage, check the air valve and tighten the valve with the provided
wrench first. (Fig. 1).
Attention: Don't adjust the air valve when the board is in use.
Warning: Don't rotate the wrench counterclockwise when inspect the inflation, or it will be danger.
3. Inflate the board by unscrewing the cap of the air valve (Fig.2 Pos.1). Ensure that the inner spring valve is not
depressed. If it is depressed (Fig.2 Pos. 2), press the spring valve and turn counter clockwise so the inner spring
valve is in the correct position (Fig.2 Pos. 3). Attached the hose to the inflate position on the high-pressure hand
pump. Inflate the board to 1.034bar (15psi). After inflation, screw the cap of air valve (Fig.2 Pos. 4)
NOTE: If over-inflation occurs, press the spring valve to release air to an acceptable level and securely fasten the air
valve.
NOTE: If the board is not in use and exposed under the sun, it may cause overexpansion and damage the board.
Check the pressure and deflate slightly until the correct pressure is obtained.
NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just for reference, should
not be used as a precision instrument.
1
Fig. 1
4. Attach the safety rope to the tow ring, and place the belt around your ankle (Fig.3).
#65302 #65304
Oar Installation (65302)
Adjust the oar length according to your height.
Take your height and add 8" for surfing length and 10" for touring length.
Deflation
Maintance:
1. Inflate according to the PSI marked besides the valve;
2. To avoid the long-time exposure to sunshine or rain, put the outside cover on top for protection when it not being
used;
3. Clean it with mild soap water and soft cloth in case it is not going to be used for a long time. Dry it before putting
them away. Store it at a dry and shady place and keep it out of reach of Children.
Storage
1. Deflate the board by unscrewing the cap of air valve, press the spring valve and turn clockwise.
2. Remove all the accessories from the board. Use a cloth to gently dry all surfaces. Keep the board and all accessories
clean and dry.
3. Fold the board from front to back to remove additional air.
4. Store in a cool, dry place and out of children's reach.
NOTE: Do not unfold this product when the temperature is low, leave the product in the room
temperature (over 20ºC) for 24 hours before inflation.
Repair
• Fully clean the area to be repaired.
• Cut the correct size from the repair patch material.
• Apply only the amount of glue (not included) needed to cover the repair site.
1
2 3 4
Fig. 2
Fig. 3
MAX
MAX
Easily adjust the length
S-S-005544