Stanley STHM5 Original Instruction page 5

at all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
Hammer safety warnings
Wear ear protectors. Exposure to noise can cause
u
hearing loss.
Use auxiliary handle(s), if supplied with the tool.
u
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting acces-
sory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
Be certain that the material being drilled does not con-
u
ceal electric or gas service and that their locations have
been verified with the utility companies.
Keep a firm grip on the tool at all times. Do not
u
attempt to operate this tool without holding it with
both hands. Operating this tool with one hand will result
in loss of control. Breaking through or encountering hard
materials such as re-bar may be hazardous as well.
Tighten the side handle securely before use.
Ensure the chisel is secured in place before operating
u
the tool.
In cold-weather conditions or when the tool has not been
u
used for a longer period of time, let the tool run with no
load for several minutes before use.
When working above ground level ensure the area below
u
is clear.
Do not touch the chisel or the parts close to the chisel
u
immediately after operation, as they may be extremely
hot and cause burns to the skin.
Always direct the power cable to the rear, away from the
u
chisel.
Do not operate this tool for long periods of time.
u
Vibration caused by hammer action may be harmful to
your hands and arms. Use gloves to provide extra cush-
ion and limit exposure by taking frequent rest periods.
Other risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc. In spite of the
application of the relevant safety regulations and the imple-
mentation of safety devices, certain risks cannot be avoided.
These are:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
E NG L I S H
5