Page 1
Form L-1383 12/11, Rev. B Installation, Operation, Repair and Parts Manual Description Hypro high pressure diaphragm pumps are recommended are designed for optimum performance of medium to for spraying of herbicides, pesticides, liquid fertilizers and large-sized sprayers. Hypro high pressure diaphragm many other hard to handle fluids.
An unsecured discharge line may whip, causing the warranty will be void. If there are any personal injury and/or property damage. questions, call the Hypro Applications toll-free 12. Check the hoses for weak or worn condition before number: 800-445-8360. each use. Make certain that all connections are tight 3.
1. Be sure the oil is halfway up the clear oil sight tube. If 4. The relief valve bypass port should be connected back necessary, fill to the correct level with Hypro Oil to the liquid tank unrestricted. Do not hook the bypass (Part Number 2160-0038).
1. After use, flush the pump with clean water. Valve Replacement Occasionally debris can cause the valves to not seat 2. Hypro diaphragm pumps come with oil in the properly or damage the o-rings. To check for this problem, crankcase. Hypro recommends follow these steps.
NOTE: When ordering parts, give QUANTITY, PART NUMBER, DESCRIPTION, and COMPLETE PUMP MODEL NUMBER. 8. Refill the crankcase with Hypro Oil (part number Reference numbers are used ONLY to identify parts in the drawing and are NOT to be used as order numbers.
Page 6
Parts List for 9910-KIT2204, 9910-KIT2200 and 9910-KIT2203 Figure 3. Female Splined Coupler Kit 9910-KIT2204 Figure 4. Male Splined Shaft Kit 9910-KIT2200 and Installation Solid Shaft Kit 9910-KIT2203 Parts List for 9910-KIT2204 Parts List for 9910-KIT2200 and 9910-KIT2203 REF. PART QTY. REF.
Page 7
Insert the 8x25 mm allen head bolts (Ref. 11) through 1. On the 9910-D813, -D1064 and -D1265, the square the gearbox body (Ref. 8) and thread into the engine metal plate must be removed from the shaft side of the flange adapter (Ref.
Control Unit 9910-GS50GI The 9910-GS50GI control unit is designed for the control of pressures up to 725 psi and flows up to 48 gpm. It consists of an adjustable pressure relief valve, a manual pressure release lever, and three individual ball valve-controlled, 1/2" O.D., hose barb outlets.
Page 9
Parts List for Control Unit 9910-GS50GI 33 62 36 25 29 REF. PART QTY. REF. PART QTY. NUMBER DESCRIPTION REQÕD. NUMBER DESCRIPTION REQÕD. 9910-380240 9910-680500 Regulating spring 9910-620610 M8x30 Bolt 9910-680510 Spring guide 9910-850711 Flange 3/4Ó 9910-680520 Lever guide ¥ 9910-550350 O-Ring 9910-680530...
Page 10
Control Unit 9910-VDR50 The Model 9910-VDR50 Control Unit is designed for the control of pressures up to 725 psi and flows to 35 gpm. It consists of an adjustable pressure relief valve, a manual pressure release lever, and two individual ball valve- controlled, 1/2"...
Page 11
Parts List for Control Unit 9910-VDR50 NOTE: When ordering parts, give QUANTITY, PART NUMBER, DESCRIPTION, and COMPLETE MODEL NUMBER. Reference numbers are used ONLY to identify parts in the drawing and are NOT to be used as order numbers. In With Pump REF.
Page 12
Parts Illustrations for Model 9910-D813 NOTE: Head setup from Valve Cap side Ref. 15 SX Ref. 21 DX Ref. 15 Form L-1383 (12/11, Rev. B) - 12 -...
Page 13
Parts List for Model 9910-D813 REF. PART QTY. REF. PART QTY. NUMBER DESCRIPTION REQÕD. NUMBER DESCRIPTION REQÕD. 9910-580360 Retaining bolt 9910-620610 M8x30 Bolt 9910-1040180 Retaining bolt washer 9910-1040760 Outlet adapter (3/4" BSP) 9910-1040080 Diaphragm, Desmopan (Std.) 9910-1040761 Outlet adapter (3/4Ó NPT) 9910-1040081 Diaphragm, Buna-N (Opt.)
Page 14
Parts Illustrations for Model 9910-D1064 49 35 NOTE: Head setup from Valve Cap side 40 66 Ref. 15 Ref. 19 Ref. 19 Ref. 15 - 14 - Form L-1383 (12/11, Rev. B)
Page 15
Parts List for Model 9910-D1064 REF. PART QTY. REF. PART QTY. NUMBER DESCRIPTION REQÕD. NUMBER DESCRIPTION REQÕD. 9910-580360 Retaining bolt 9910-620610 M8x30 Bolt 9910-1040180 Retaining bolt washer 9910-1040760 Outlet adapter (3/4" BSP) 9910-1040080 Diaphragm, Desmopan (Std.) 9910-1040761 Outlet adapter (3/4" NPT) 9910-1040081 Diaphragm, Buna-N (Opt.) 9910-110131...
Page 16
Parts Illustrations for Model 9910-D1265 NOTE: Head setup from Valve Cap side Form L-1383 (12/11, Rev. B) - 16 -...
Page 17
Parts List for Model 9910-D1265 REF. PART QTY. REF. PART QTY. NUMBER DESCRIPTION REQÕD. NUMBER DESCRIPTION REQÕD. 9910-580360 Retaining bolt 9910-680350 M8x35 Bolt 9910-1040180 Diaphragm retainer washer 9910-680031 Oil reservoir 9910-1040080 Diaphragm-Desmopan (Std.) 9910-1800060 Black cap 9910-1040081 Diaphragm-Buna-N (Opt.) 9910-680040 Oil breather cap 9910-104008T Diaphragm, Buna-N with...
Page 18
Parts Illustrations for Model 9910-D1516 NOTE: Head setup from Valve Cap side Form L-1383 (12/11, Rev. B) - 18 -...
Page 19
Parts List for Model 9910-D1516 REF. PART QTY. REF. PART QTY. NUMBER DESCRIPTION REQÕD. NUMBER DESCRIPTION REQÕD. 9910-580360 Retaining bolt 9910-540530 Threaded adapter 9910-1040180 Diaphragm retainer washer 9910-250310 O-ring 9910-1040080 Diaphragm, Desmopan (Std.) 9910-540540 Hose barb nut 9910-1040081 Diaphragm, Buna-N (Opt.) 9910-540550 Hose barb 1-1/2"...
Page 20
Pump Performance for Series D813, D1064, and D1265 U.S Units 350 RPM 400 RPM 450 RPM 500 RPM 550 RPM 14.7 17.0 18.2 19.7 13.5 15.5 17.3 19.0 19.6 13.4 15.2 17.1 18.3 19.2 13.3 14.9 16.9 17.8 18.7 Metric Units 350 RPM 400 RPM 450 RPM...
Page 22
NOTES Form L-1383 (12/11, Rev. B) - 22 -...
Page 23
NOTES Form L-1383 (12/11, Rev. B) - 23 -...
Page 24
Contact Hypro Service Department at 800-468-3428 to receive a Return Merchandise Authorization number (RMA#). Returns are to be shipped with the RMA number clearly marked on the outside of the package. Hypro shall not be liable for freight damage incurred during shipping. Please package all returns carefully. All products returned for warranty work should be sent...
Need help?
Do you have a question about the 9910-D813 and is the answer not in the manual?
Questions and answers