Hypro 9047 Series Installation, Operation, Repair And Parts Manual

Gear-driven centrifugal pumps

Advertisement

Quick Links

Installation, Operation, Repair and Parts Manual
Hypro Centrifugal Pumps handle big, high-capacity farm
spraying jobs with ease. Use them for spraying liquid fer-
tilizers and other chemicals, including wettable powder
slurries for weed control. Make short work of other farm
jobs - filling nurse tanks, watering seed beds, and trans-
ferring liquids.
Series 9047
Gear-Driven Centrifugal Pumps
Description
SERIES 9047C
Cast Iron, Gear-Driven
Centrifugal Pump
Max. Flow Rate: ..........213 gpm
Max. Pressure: ..............180 psi
Max. Speed:..................540 rpm
Ports: ....................2"" NPT inlet
1-1/2" NPT outlet
SERIES 9047C-SP
and 9047C-BSP
Cast Iron, Gear-Driven,
Centrifugal Pump
Max. Flow Rate: ..........195 gpm
Max. Pressure: ..............170 psi
Max. Speed:..................540 rpm
Ports: ............ 2" NPT inlet (SP)
2" NPT outlet (SP)
2" BSP inlet (BSP)
2" BSP outlet (BSP)
Hypro gear-driven centrifugal pumps are sturdy, smooth
running units and are available in both standard and self-
priming models.
Form L-1529
12/11, Rev. C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9047 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hypro 9047 Series

  • Page 1 12/11, Rev. C Installation, Operation, Repair and Parts Manual Description Hypro Centrifugal Pumps handle big, high-capacity farm Hypro gear-driven centrifugal pumps are sturdy, smooth spraying jobs with ease. Use them for spraying liquid fer- running units and are available in both standard and self- tilizers and other chemicals, including wettable powder priming models.
  • Page 2: General Safety Information

    General Safety Information Notes are used to notify of installation, operation, or Warning denotes that a potential hazard exists and maintenance information that is important but not indicates procedures that must be followed exactly safety related. to either eliminate or reduce the hazard, and to avoid serious personal injury, or prevent future safety problems with the product.
  • Page 3: Plumbing Installation

    Plumbing Installation Centrifugal Plumbing Hook-up REF. DESCRIPTION Tank Lid Vent Line #3430-0456 Jet Agitator Shut-off Ball Valves Centrifugal Pump Spray Control Console Centrifugal Pump Control Manifold Boom Valve Electromagnetic Flowmeter Compact Jet Turret Nozzle Body L-1529 (12/11, Rev. C)
  • Page 4: Installation Instructions

    Hypro directly at Centrifugal Pump Control www.hypropumps.com or by Hypro now offers many different components for spray- ing systems. The Hypro centrifugal pump control incor- calling 1-800-424-9776. porates the electric flow control valve, a self-cleaning line strainer, a visual pressure gauge and a manual agi- tation control valve.
  • Page 5: Operation And Maintenance

    Operation and Maintenance Flush Pump After Use One of the most common causes for faulty pump perform- Engage the PTO clutch slowly and smoothly. Avoid ance is “gumming” or corrosion inside the pump. Flush the sudden starts and fast clutching that may damage pump and entire system with a solution that will chemically the drive section of the pump.
  • Page 6: Repair Instructions

    Repair Instructions Always flush the pump with water or neutralizing agent before servicing. Pump Housing Dissassembly 1. Remove the six casting cap screws with a 5/8” box wrench. Tap pump casing on discharge port with rubber hammer, if needed. Check inside of pump casing, including suction port. If badly eroded (or damaged), pump casting should be replaced.
  • Page 7 Repair - continued Be extremely careful with the new seal. Silicon carbide material is very hard, but also very brittle. If the seal is accidentally dropped and hits a hard surface, the seal’s primary ring (rotary part) and mating ring (stationary seal seat) can be damaged. Also take precautions not to introduce dirt or grit to the seal surfaces.
  • Page 8: Troubleshooting

    Troubleshooting Symptom Probable Cause(s) Corrective Action(s) Low Discharge Pump not primed. - Remove topmost vent plug from face of pump and run pump to expel trapped air (See Installation Instructions). Air leaks in suction line. - Check and reseal inlet fittings. Blocked or clogged line strainer.
  • Page 9 9047 Series Pumps Seal Kit No. 3430-0779 Ref. Qty. Part consists of: No. Req'd. No. Description (1) Ref. 4 O-ring and (1) Ref. 5 0153-9200C1 Pump Casing (with SS wear ring) Mechanical Seal 0152-9275C2 Pump Casing (Self-Priming Model) - NPT...
  • Page 10 Notes L-1529 (12/11, Rev. C)
  • Page 11 Notes L-1529 (12/11, Rev. C)
  • Page 12 Contact Hypro Service Department at 800-468-3428 to receive a Return Merchandise Authorization number (RMA#). Returns are to be shipped with the RMA number clearly marked on the outside of the package. Hypro shall not be liable for freight damage incurred during shipping. Please package all returns carefully. All products returned for warranty work should be sent shipping...

This manual is also suitable for:

9047c-sp series9047c-bsp series

Table of Contents