Subscribe to Our Youtube Channel
Related Manuals for Ruijie RG-WS6108 Series
Summary of Contents for Ruijie RG-WS6108 Series
- Page 1 RG-WS6108 Series Wireless Controller Hardware Installation and Reference Guide V1.01...
- Page 2 This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.
- Page 3 It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it is assumed that the users are already familiar with the related terms and concepts. Obtaining Technical Assistance Ruijie Networks Website: https://www.ruijienetworks.com/ Technical Support Website: https://ruijienetworks.com/support...
-
Page 4: Product Overview
Product Overview The RG-WS6108 wireless LAN controller is introduced by Ruijie Networks to provide powerful access control capability for medium-large-sized wireless networks. RG-WS6108 Table 1-1 Technical Specifications of RG-WS6108 RG-WS6108 Model DDR3 SDRAM: 2GB BOOTROM: 8MB Memory FLASH: 128MB Eight RJ45 copper ports, two Gigabit SFP fiber ports... - Page 5 LED Indicators State Meaning The power module is NOT in the position or fails. Solid green The power module is operational. Blinking green The system is being initialized. Solid green The initialization process is complete. Solid red The system sends out an alarm. Solid green The copper port is connected at 10/100/1000 Mbps.
-
Page 6: Preparation For Installation
Misuse of battery may cause damage to the device or hurt to people. Do not replace battery by yourself. Instead, contact Ruijie Service Center for the replacement of battery. This device is an A-class product. It may cause radio interference in living environment, which may require you to take anti-interference measures. -
Page 7: Cleanness Requirements
Relative Temperature Relative Temperature Long-time Working Short-time working Long-time Working Short-time Working Condition Condition Condition Condition 15º C to 30º C 0º C to 45º C (32 to 113º F) 40%~65% 5%~95% The ambient temperature and humidity are measured at a point 1.5 meters (4.9 feet) above the ground and 0.4 meters (1.3 feet) before the device when there is no protective board in the front or back of the rack. -
Page 8: Anti-Interference Requirements
Take dust prevention measures in the room. Maintain an appropriate humidity and temperature. Always wear an anti-static wrist strap when you touch any circuit board. Place the circuit board on an anti-static workbench or in an anti-static shielding bag. ... -
Page 9: Installation Flowchart
Installing Wireless Controller Installation Flowchart Please follow the following procedure to install the wireless controller to ensure the smooth installation and avoid any damage to the device. Begin Read Chapter 2 Ensure Requirements are Met Mount Wireless Controller Connect Cables Verify Installation Power on Wireless Controller Configure Wireless Controller... -
Page 10: Installing Power Cable
Mounting RG-WS6108 on Workbench In the absence of a 19-inch standard cabinet, install the wireless controller on a clean workbench. During the operation, pay attention to the following items: The workbench is firm and well-grounded. The supplied plastic cushion is stuck to the small hole at the bottom of the wireless controller and a 10 cm clearance is reserved for dissipation. -
Page 11: Connecting Console
Connecting Console RG-WS6108 supplies an EIA/TIA-232 configuration console for local configuration. If you configure RG-WS6108 through Web, skip this part. Table 3-1 Console Attributes Parameter Description Connector RJ-45 Asynchronous EIA/TIA-232 Interface Standard Baud Rate 57,600 bps, 115,200 bps, 9,600 bps (default) Command line interface Supported Services Connection to character terminals... -
Page 12: Configuration Guide
Configuration Guide Setting up Configuration Environment When you use the wireless controller for the very first time, you will need to configure it through a console port as follows: As shown in the following figure, connect the serial port of a character terminal or microcomputer to the console port through an RS232 cable. -
Page 13: Verification Before Power-On
Figure 4-3 Setting Communication Parameters for Serial Port. After building the configuration environment, you may power on the wireless controller Powering on Wireless Controller Verification Before Power-on Before powering on the wireless controller, please check the following items:... -
Page 14: Startup Process
If the power cable and the grounding cable are connected correctly. If the power supply voltage meets the requirement. If the configuration cable is connected correctly, the microcomputer or terminal is turned on, and the setting is complete. - Page 15 0.000000] CPU revision is: 000d910a (Cavium Octeon II) 0.000000] Checking for the multiply/shift bug... no. 0.000000] Checking for the daddiu bug... no. 0.000000] Determined physical RAM map: 0.000000] memory: 000000000003f000 @ 0000000000dd1000 (usable after init) 0.000000] memory: 000000000f000000 @ 0000000000f00000 (usable) 0.000000] memory: 00000000d0000000 @ 0000000020000000 (usable) 0.000000] memory: 000000000ffff000 @ 00000000f0001000 (usable) 0.000000] memory: 000000030efff000 @ 0000000100001000 (usable)
-
Page 16: Power Troubleshooting
Troubleshooting Power Troubleshooting You may use the power indicator on the front panel to decide if the power supply system is operating normally. For description of indicators, see Chapter 1. If a fault occurs, check the following items: If RG-WS6108 power switch is in the on position. ...
Need help?
Do you have a question about the RG-WS6108 Series and is the answer not in the manual?
Questions and answers