Advertisement
ZS 5062
SPEAKER ZONE SELECTOR
ZS 5122
SPEAKER ZONE SELECTOR
Thank you
for choosing another quality product from Amperes Electronics.
After much improvements made to the earlier models, Amperes ZS5062 and ZS5122 finally rolled out with better
features and outlooks.
The original features of emergency paging microphone input port and remote triggering are maintained. However a
priority overtaking LED is added to the front panel to alert the user that paging from remote is active and thus the
BGM zone selected has been bypassed.
With this new product, you are assured that we live up to our policy, ie. continuous improvement to give you the
products that are contemporary and with better value without increment in cost.
Although it is not difficult to install this unit, a brief reading of the manual is truly recommended to avoid any
misconnection as well as to explore the potential usage of the product to its maximum.
ALL CALL
1
2
OVERRIDE
SPEAKER ZONE SELECT
ALL CALL
1
2
OVERRIDE
3
4
5
6
3
4
5
6
7
SPEAKER ZONE SELECT
8
9
10
11
12
amperes
amperes
VER 1 / 2014
Advertisement
Table of Contents
Related Manuals for Amperes ZS5062
Summary of Contents for Amperes ZS5062
- Page 1 Thank you for choosing another quality product from Amperes Electronics. After much improvements made to the earlier models, Amperes ZS5062 and ZS5122 finally rolled out with better features and outlooks. The original features of emergency paging microphone input port and remote triggering are maintained. However a priority overtaking LED is added to the front panel to alert the user that paging from remote is active and thus the BGM zone selected has been bypassed.
- Page 2 The LED shall lit if remote paging microphone is active and is overriding the local BGM zone selection. This is active if Amperes PM 1060 paging is used or any other paging microphone console with Priority output signal. 2. ALL CALL SWITCH All zones will be activated by pressing this switch, regardless of any inactive zone.
- Page 3 Please refer to section ‘ Firmware Upgrading’ to perform the Firmware update process. 8. UNIT ADDRESS DIP SWITCH When it is required to be linked to Amperes PMX II software for monitoring purpose, the unit / units are required to be addressed. Binary code addressing is used in setting the unit’s ID.
- Page 4 Single Unit Installation With Remote Select POWER AMP 1 24 DC The sample connections shown are using a single unit of either ZS5122 or ZS5062 in a small scale installation. ie. small number of zone outputs. AMP 1 ZON1 AMP 2...
- Page 5 And the connection Z PR must link. Use EP1200A to make ALL CALL to all ZS installed - refer to page 6. PAGE 5 ZS5062 / ZS5122 6 / 12 CHANNEL SPEAKER ZONE SELECTOR...
- Page 6 7-24V Quality Product From 8-COM AMPERES ELECTRONICS triggering the relay output ; ie. this shall not override the volume controllers to volume controllers overriding PAGE 6 ZS5062 / ZS5122 6 / 12 CHANNEL SPEAKER ZONE SELECTOR...
- Page 7 Individual, All Call Local zone selection bypassed when remote trigger is activated Dimensions (W x H x D) 482 x 44 x 180 mm Weight 1.85 kg 2 kg PAGE 7 ZS5062 / ZS5122 6 / 12 CHANNEL SPEAKER ZONE SELECTOR...
- Page 8 Only Amperes Electronics Service Centres are allowed to make warranty repairs : a list of Amperes Electronics Service Centres may be asked for by the purchaser or send directly to Amperes Electronics Sdn Bhd at 70 Jalan Industri PBP 3, Tmn Perindustrian Pusat Bandar Puchong, 47100, Puchong, Selangor, Malaysia or its authorized master distributor, Amperes Global Marketing.
Need help?
Do you have a question about the ZS5062 and is the answer not in the manual?
Questions and answers