Maytag MHN33PD Installation Instructions Manual page 15

CODE
h. 01 SUPER CYCLE TYPE
(Skipped unless Super Cycle pricing is enabled.)
h. 01 This represents the Super Cycle upgrade option.
Press the BRIGHTS key pad to step through
upgrade options 1–3 as follows:
01 – enhanced wash, extra three minutes of wash
tumble in addition to the programmed wash time.
02 – extra rinse for all cycles.
03 – both 01 and 02.
Press the DELICATES AND KNITS key pad once
g
to advance to next code.
COIN/DEBIT OPTION
J. Cd
J. Cd Both coin & debit selected. Press the
QUICK CYCLE key pad three consecutive
times to change this selection.
J. C_ Coins selected, debit disabled. Press the
QUICK CYCLE key pad three consecutive
times to change this selection.
J. _d Debit card selected, coins disabled. This is
the factory default for PN models. Press the
QUICK CYCLE key pad three consecutive times
to change this selection.
J. Ed Enhanced Debit is self-selected when a
Generation 2 card reader is installed in the
washer. The Ed option cannot be manually
selected or deselected.
g Press the DELICATES AND KNITS key pad once
to advance to next code.
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to show
'ADD' or 'AVAILABLE' rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected 'OFF.'
L. PS Selected 'ON.' Press the QUICK CYCLE key pad
once for this selection.
g Press the DELICATES AND KNITS key pad once
to advance to next code.
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
00 Not Selected 'OFF'.
CE Selected 'ON'. Press the QUICK CYCLE key pad
once for this selection.
g Press the DELICATES AND KNITS key pad once
to advance to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the BRIGHTS key pad. Factory pre-set
for 800 rpm.
g Press the DELICATES AND KNITS key pad once
to advance to next code.
U. 00 PENNY INCREMENT OFFSET
U. 00 This option is not supported for European Models
and the value must be set to 00.
Press the DELICATES AND KNITS key pad once
g
to advance to next code.
EXPLANATION CODE
PREWASH LENGTH
A1. 00
A1. 00 This is the number of minutes of Prewash.
Choose 0 to disable the prewash or select
between 2 and 7 minutes by pressing the
BRIGHTS key pad.
g Press the DELICATES AND KNITS key pad once
to advance to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of final high-speed
spin. Choose from 3–8 minutes by pressing the
BRIGHTS key pad.
Press the DELICATES AND KNITS key pad once
g
to advance to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Number of cycles in HUNDREDS.
2 00 Number of cycles in ONES.
This is 'VIEW ONLY' and cannot be cleared.
g Press the DELICATES AND KNITS key pad once
to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following
is true:
3 00 Currency amount in HUNDREDS.
4 00 Currency amount in ONES.
5 00 Currency amount in HUNDREDTHS.
END OF SETUP PROCEDURES
EXIT FROM SETUP MODE
PD Models: Reinstall access door.
■
PN Models:
■
– Unplug washer or disconnect power.
– Open console, reinsert plug into AA1, close console.
– Plug in washer or reconnect power.
PN MODELS WITH PROGRAMMING SWITCH:
■
Turn key clockwise and remove.
PN MODELS SET UP WITHOUT PROGRAMMING SWITCH:
■
Set-up mode can be exited by using procedures from
Service Access Code (Below).
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for 0
vend price without any Special Pricing setup, and the Coin/Debit
Option must be set to "J._d". If the washer is not in failure mode,
the door must be opened to proceed.
To enter the Service Access Code, press these key pads
in the following order: 1 – upper left, 2 – lower right, 3 – upper
right, 4 – lower left.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15-second delay before it
can be attempted again.
There are three options to exit from the Service Mode:
1. Power down the washer; then reapply power.
2. Wait two minutes without touching any key pads (without
diagnostic modes running).
3. From Set-Up Code 8, press key pad #1 for four seconds.
EXPLANATION
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225
3 01 = 100.00
4 68 = 68.00
5 75 = 00.75
TOTAL = 168.75
15