Subscribe to Our Youtube Channel
Related Manuals for ITW Simco-Ion D167Q
Summary of Contents for ITW Simco-Ion D167Q
- Page 1 MEB & MEJ Static Neutralizing Bars and Power Supplies (D167RY, D167Q, F167, F267, N167 and N267) INSTALLATION AND OPERATING INSTRUCTIONS MEB & MEJ BARS 5200214 Rev. F...
- Page 2 (This page intentionally left blank) MEB & MEJ BARS 5200214 Rev. F...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. SAFETY WARNINGS ....................1 2. INTRODUCTION ......................2 Receipt of Equipment ......................2 Return Shipments ........................2 3. SPECIFICATIONS .....................3 4. INSTALLATION ......................4 Grounding ..........................4 Mounting Static Neutralizing Bars ..................4 Mounting Power Supplies .....................4 Installing High Voltage Cables .....................5 5. OPERATION ......................5 6. -
Page 4: Safety Warnings
1. SAFETY WARNINGS NOTE! – Statements identified with a NOTE indicate precautions necessary to avoid potential equipment failure. CAUTION! – Statements identified with a CAUTION indicate potential safety hazards. NOTE! – This equipment must be correctly installed and maintained. Adhere to the following notes for safe installation and operation. 1. -
Page 5: Introduction
2. INTRODUCTION Simco-Ion’s D167RY, D167Q, F167, F267, N167 and N267 power supplies are designed as a power source for the MEB and MEJ static neutralizing bars. This equipment is used to eliminate or significantly reduce static charges that disrupt manufacturing processes. The high voltage from the power supply causes the ionizing pins of the static neutralizing bar to generate both positive and negative ions from surrounding air molecules. -
Page 6: Specifications
3. SPECIFICATIONS Output Voltage 7 kV 7 kV Temperature 110°F (43°C) max Humidity 70% RH max, no dewing permissible Dimensions 5/8”W x 3/4”H 11/16” dia Enclosure Stainless Steel (Type 304) Aluminum Inner Bar Material Rigid Polyvinyl Chloride (PVC) Emitter Point Stainless Steel (Type 302) F167 D167Q... -
Page 7: Installation
4. INSTALLATION Grounding 1. It is essential that the machine frame be grounded either through well-grounded electrical conduit or by heavy copper wire connecting the frame to a water pipe. 2. The static neutralizing bar’s metal casing must be grounded to avoid operator shock and to ensure proper operation. -
Page 8: Installing High Voltage Cables
Installing High Voltage Cables 1. Route the high voltage cables attached to each static bar along the machine frame or wall to the power supply. 2. Cable supports are used to guide the cables back to the power supply. All cables must be kept a minimum of 1/4”... -
Page 9: Troubleshooting
6. TROUBLESHOOTING NOTE! – Only qualified service personnel are to perform trouble-shooting tasks. If equipment fails to function properly: 1. De-energize the power supply. 2. Ensure all ground connections are intact. 3. Check that all cable connections are tight. NOTE! – FINGER TIGHTEN ONLY. 4. -
Page 10: Maintenance
7. MAINTENANCE NOTE! – Only qualified service personnel are to perform maintenance tasks. NOTE! – Never use hard or sharp objects to scrape ionization points. CAUTION! – ELECTRICAL SHOCK HAZARD De-energize all power supplies before performing any maintenance tasks. CAUTION! – FIRE HAZARD Never energize a power supply with any trace of alcohol remaining on the equipment. -
Page 11: Replacement Parts
8. REPLACEMENT PARTS 5050227 MEB Bar mounting kits (contains 2 brackets and hardware) 5050228 MEJ Bar mounting kits (contains 2 brackets and hardware) 5050001 SLCC HV Connector Kit 4800061 Plastic Insulating Tubing 4104946 Insulated HV Cable Supports 4670204 Cleaning Brush 4050556 Tension Voltage Detector 9. - Page 12 Simco-Ion 2257 North Penn Road Hatfield, PA 19440 (215) 822-6401 (800) 203-3419 www.simco-ion.com customerservice@simco-ion.com © 2019 Simco-Ion Printed in the U.S.A. MEB & MEJ BARS 5200214 Rev. F...
Need help?
Do you have a question about the Simco-Ion D167Q and is the answer not in the manual?
Questions and answers