Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Efitment T017
Summary of Contents for Efitment T017
- Page 1 T017 ADJUSTABLE INCLINE MANUAL TREADMILL WITH ARM EXERCISERS USER MANUAL IMPORTANT！Read all instructions carefully before using this product. Retain this manual for future reference. For customer service, contact service@zoovaa.com.
- Page 2 PRECAUTIONS WARNING:TO REDUCE THE RISK OF SERIOUS INJURY, READ THE FOLLOWING IMPORTANT PRECAUTIONS BEFORE USING THE TREADMILL. 1. Read all instructions in this instruction book before using the treadmill. Use the treadmill only in the way described in this instruction book. 2.
-
Page 3: Exploded View
EXPLODED VIEW... -
Page 4: Part List
PART LIST DESCRIPTION Q’TY Main frame Bottom frame Left side hand post Right side hand post Handle bar Base of the magnet Front roller Front axle Rear roller Rear axle Bolt M6*75L Washer OD13*ID6.2 Bolt M6*75L Bolt M5*20L Bolt M3*10L Sensor wire connector Bolt M8*45L Bolt M5*20L... - Page 5 PART LIST DESCRIPTION Q’TY Base frame cushion Computer Plug Plastic end cap Magnet Running board Running belt Tension knob Handle bar (R) Handle bar (L) Incline Adjuster Bolt M8*15L Bolt M6*10L Bolt M8*45L Bolt M4*12L Bolt M10*60L Washer OD16*ID8.3 Arc washer OD16*ID8.3 Washer OD22*ID10.3 Washer OD12*ID4.2 Knob M8*60L...
- Page 6 ASSEMBLY NOTICE Read this manual before assmbly Check the spare parts first. Check the hardware. Ensure that you have the right tool. Prepare an area to assemble. Follow the instructions accordingly. Never force the joints NOTICE ...
- Page 7 ASSEMBLY DESCRIPTION Q’TY NO. DESCRIPTION Q’TY Main Frame Plastic Cover Bottom Frame Computer Left Side Hand Post Cover of Handle Right Side Hand Post 48R Handle bar (R) Handle Bar Handle bar (L)
-
Page 8: Assembly Parts List
ASSEMBLY PARTS LIST... - Page 9 NOTE: The assembly parts list is included for your reference. Some parts are preassembled on the machine. In these instances, simply remove and reinstall the parts as required. ASSEMBLY STEP 1 Attach Right and Left Side Hand Posts (3 & 4) to the Bottom Frame (2), then fasten them with Bolts, Washers and Arc Washers (A, F &...
- Page 10 STEP 2 Before you assemble the HIGH tension cable, make sure that it is at level 8. To assemble the magnetic tension adjustment mechanism: 1. Insert tension wire into the gap in the Baffle Plate (R), then lower Steel Wire Cap (T) into the hole in Baffle Plate (R).
- Page 11 2.Pull Tension Sleeve (X) downward to bring Baffle Plate (R) close to Tension Permanent Seat (S), then insert V into Tension Permanent Seat (S). 3.Turn Tension Nut (U) clockwise in order to tighten Tension Nut (U) and Tension Bolt (V) well.
- Page 12 STEP 3 Cover the flywheels with Plastic Cover (38), then secure it with Screws (B) and Washer (K). STEP 4 Ensure the holes are aligned. Stabilize the Right and Left Side Hand Posts (3 & 4) and raise the Main Frame (1). Attach Right and Left Side Hand Posts (3 &...
- Page 13 STEP 5 Connect the Sensor Wire Connectors (24 & 22). STEP 6 Place the Handrail (5) onto the Right and Left Side Hand Posts (3&4) and secure them with Bolts (C) and Arc Washers (G). Connect the Sensor Wire Connectors (17 &...
- Page 14 STEP 7 Unscrew Bolt (D) and Washer (I) from plastic base of the Computer (41). Attach the Computer (41) to the Handrail (5), Insert the Sensor Wire Connector (17) and the Hand Pulse Connector (26) into the Computer (41), and then secure with Bolt (D) and Washer (I).
-
Page 15: Adjusting The Incline
NOTE: Always use proper lifting technique to prevent injury. ADJUSTING THE INCLINE There are 3 incline angles (A: 7°, B: 8°, C: 9° ). To adjust the incline, lift the rear end of the main frame up, and use your other hand to adjust the incline adjuster to the desired position. -
Page 16: Adjusting The Belt
FOLDING Loosen Knob (J) completely before folding. Lift Main Frame to the upright position. Put Knob (J) back in and tighten. ADJUSTING THE BELT If the belt is not centered correctly, the machine will be noisy. If the belt is too tight, too loose or not centered, use the 5mm wrench to adjust it. If the belt drifts to the right, turn the right screw 1 or 2 turns. -
Page 17: Adjusting The Tension
ADJUSTING THE TENSION The user can set the desired tension according to the picture below: To decrease the tension, turn Bolt (13) clockwise. To increase the tension, turn Bolt (13) counterclockwise. After adjusting the Bolt (13), check if the tension wire is too loose. If necessary, adjust the Bolts (U or W) on tension wire. - Page 18 The cross training magnetic treadmill has moving handlebars that let you exercise your arms and upper body. Use the moving handlebars as shown in the picture below. You can exercise with just the handlebars or use them while walking on the treadmill. HOW TO SET UP THE TENSION OF THE HANDLEBARS Use Knob (P) to adjust the tension of the moving handlebars.
-
Page 19: Maintenance
MAINTENANCE Treadmill Lubrication To reduce the friction of the walking belt and minimize wear, apply lubricant directly onto the Treadboard and underside of the Belt. Lift one side of the Belt and feel the top surface of the Treadboard. If the surface is wet to the touch, no lubrication is required. -
Page 20: How To Move Thetreadmill
HOW TO MOVE THETREADMILL Before attempting to move the treadmill, please make sure that it has been properly folded. The Knob (J) must be tightened Start by placing two hands at position "25" to support the treadmill. Next, please place one foot at position "39"... - Page 21 OPERATING INSTRUCTIONS TIME………………………………………….……….00:00~99:59 MIN SPEED………………………………………….....0.0~99.99 MI/H DISTANCE……………………………………….…..0.0~999.9 MI CALORIE………………………………………………..0.0~999.9 KCAL ODOMETER……………………………………………………0~9999 MI PULSE……………………………………….....40~220 BPM The display will turn on when you start walking on the treadmill or when you press a key. After 4-5 minutes of inactivity, the display will shut off automatically. When the treadmill is not moving, computer will display “STOP”...
Need help?
Do you have a question about the T017 and is the answer not in the manual?
Questions and answers