Page 1
• Due to continuous product development/improvement, the specifications and configurations in this document are subject to change without prior notice. Manufactured by. 9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo, 146-8555, Japan NITTO KOHKI CO., LTD. Tel : +81-3-3755-1111 Fax : +81-3-3753-8791 (Original Instructions) TQ15292-0 06/2017...
Instructions Thank you very much for your purchase of this NITTO KOHKI product. Before using your tool, please read this manual carefully so that you may use it properly to get the most out of it. Please keep the manual handy - so you can use it whenever necessary.
California Proposition 65 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer birth defects or other reproductive harm. Some examples of these chemicals are: ...
Page 4
Precautions on Use Work area safety WARNING Do not use the tool at home. This is a professional tool (industrial or work tool for business). Do not bring the tool home and use it there. Keep the work area clean. ...
Page 5
Handling tools WARNING Storing the tool When the tool is not used, store the tool in a dry location. Also, store the tool out of the reach of children. For some tools, the storage temperature and humidity are specified. Store the tool in an appropriate location. ...
Precautions on Use General Pneumatic Tool Safety Warnings WARNING Use the tool with proper air pressure. If the air pressure is high, the rotation speed and reciprocation frequency become faster, causing damage such as damage or accelerated wear. Also, unexpected accidents could occur. ...
Page 7
Projectile Hazards WARNING Be aware that failure of the workpiece or accessories, or even of the inserted tool itself can generate high- velocity projectiles. Always wear impact-resistant eye protection while operating this tool. The grade of protection required should ...
Page 8
Precautions on Use Accessory Hazards WARNING Disconnect the tool from the energy supply before fitting or changing the inserted tool or accessory. Avoid direct contact with the inserted tool during and after use, as it can be hot or sharp. ...
Page 9
Noise Hazards WARNING Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus (ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment and implementation of appropriate controls for these hazards are essential. ...
Precautions on Use Product Specific Safety Rules WARNING Use an Abrasive Disc having the mounting hole diameter of 16 mm and external dimension of 100 mm (4"). Do not use Abrasive Discs with the allowable rotation speed (written on the Abrasive Disk, Pad, or package ...
1 Application This tool is a pneumatic hand-held sander for polishing/grinding steel materials, etc. using the Abrasive Disc. 2 Checking Inside the Package When you open the package box, check the contents of the package and also check for any damage that may have occurred during transportation.
4 Air Supply CAUTION Remove drainage before stating work. When drainage enters the tool, the vicinity of the exhaust port freezes, which could cause a loss of power. 1 Compressor 2 Air Filter 3 Air Regulator 4 Lubricator 5 Connecting Hose 6 Machine Oil 7 Coupler...
5 Preparation WARNING During work, be sure to wear eye protection, earplugs, a dust mask, and gloves (other than knitted gloves). When replacing or adjusting the Abrasive Disc or parts, be sure to detach the Connecting Hose from the tool. ...
Preparation Start and stop Start Check that the Throttle Lever is in the OFF status and insert the Connecting Hose into the Coupler of this tool Hold the tool by hand and while pulling the Lock Lever (1) toward you, press the Throttle Lever The tool starts.
6 How to Use Grinding work CAUTION Do not press the Abrasive Disc strongly against the working surface. Doing so could damage parts or damage the Abrasive Disc. Strongly pressing the tool against the working surface does not change work efficiency. Hold the tool with your hand to start Lightly touch the Abrasive Disc at an angle of 15 to 30 degrees against the working surface...
7 Maintenance and Inspection Storing the tool Store the tool according to the following warnings and cautions. WARNING When the tool is not in use, store out of the reach of children. CAUTION When the tool is not in use, store in a place with little humidity. ...
Loosen the + countersunk head screw (1) of the exhaust cover and remove the exhaust cover (2), muffler (4), spacer (3), and packing cover (5) 1 + Countersunk Head Screw 4×14 2 Exhaust Cover 3 Spacer 4 Muffler 5 Packing Cover Use a grease gun to inject grease (Sumitec 305) into the grease inlet (6) Use a grease gun nozzle with a tip outer diameter...
8 Exploded View/Parts List MYS-40 Exploded View/Parts List CAUTION Users should never perform disassembly of the tool. This illustration is for reference only. For repair or replacement of the tool, request service from the retailer where you purchased the tool or the nearest NITTO service member store.
Page 19
Part no. Part name Quantity Bearing Set Screw Ass'y TB08883 1 set Wheel Guard Ass'y TB10499 1 set Label Warning Wheel Guard (TQ15325) Driving Flange TQ14885 Outer Flange Ø16 TQ14991 Outer Flange Bolt TP09932 Ball Bearing 606ZZ *1 *2 TP03933 End Plate A TQ14869 Spring Pin 2.5×6 AW...
Page 20
10 Ubi Crescent #01-62, Ubi Techpark Lobby D, Singapore Tel: +1-630-924-9393 Fax: +1-630-924-0303 408564 Tel: +65-6227-5360 Fax: +65-6227-0192 NITTO KOHKI EUROPE GMBH NITTO KOHKI CO., LTD., Bangkok Representative Gottlieb-Daimler-Str. 10, 71144 Steinenbronn, Germany Tel: +49-7157-989555-0 Fax: +49-7157-989555-40 Office M&A Business Center, Q-House Convent Bldg., 38 Convent NITTO KOHKI EUROPE GMBH UK BRANCH Rd., Silom, Bangrak, Bangkok 10500, Thailand...