Table of Contents
Advertisement
Quick Links
AIR ABRASIVE DISC ANGLE SANDER
PNEUMATIC FILE
Please read this manual carefully before you attempt to use
your tool so that you may use it properly and safely.
MYTON
PROFESSIONAL TOOL
Rated Air Pressure
Air Consumption(No Load)
Rated Speed(No Load)
Abrasive Disc Dia.
Chack Size
Mass(Weight)
Sound Pressure Level
Sound Power Level
Vibration Level
Due to continuous product development/improvement the specifi cations and confi gurations in this
document are subject to change without prior notice.
Keep the manual handy – so you can use it whenever necessary.
Specifications
Model
[MPa]
3
[m
/min]
-1
[min
]
[mm]
[mm]
[kg]
[dB(A)]
[dB(A)]
2
[m/s
]
Manufactured by :
NITTO KOHKI CO., LTD.
2-9-4, Nakaikegami, Ohta-ku,
Tokyo 146-8555, Japan
Tel
Fax
E-mail : overseas@nitto-kohki.co.jp
URL
Model MLS-20
MLS-20
0.6
0.42
19000
25(1"), 38(1.5"), 50 (2 ")
6
0.55 (1.21 lb.)
85
96
≦ 2.5
: (03)3755-1111
: (03)3753-8791
: www.nitto-kohki.co.jp
Original Instructions
Advertisement
Table of Contents
Related Manuals for Nitto Kohki MLS-20
Summary of Contents for Nitto Kohki MLS-20
- Page 1 Vibration Level [m/s Due to continuous product development/improvement the specifi cations and confi gurations in this document are subject to change without prior notice. Manufactured by : NITTO KOHKI CO., LTD. 2-9-4, Nakaikegami, Ohta-ku, Tokyo 146-8555, Japan : (03)3755-1111 : (03)3753-8791 E-mail : overseas@nitto-kohki.co.jp...
-
Page 2: Table Of Contents
Thank you very much for your purchase of this CONTENTS page IMPORTANT SAFETY INSTRUCTIONS …………………… 2 Nitto Kohki products. GENERAL: TOOLS …………………………………………… 2 Before using your tool, please read this manual GENERAL: PNEUMATIC TOOLS …………………………… 3 carefully so that you may use it properly to get INSTRUCTIONS FOR THIS TOOL …………………………... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS BEFORE OPERATION When using the tool, please observe the safety Inspect tool before use. ● precautions below to prevent possible accident or Before using, check that screws are securely injury. tightened, that any protective cover or guard is securely in place, other parts are free from damage GENERAL : TOOLS and that the tool runs as it should. -
Page 4: General: Pneumatic Tools
Do not carry the tool by the air hose. becomes missing, contact the sales agent through Do not pull the air hose to disconnect. which you have purchased your tool or Nitto Kohki Co., Ltd. directly for a replacement. DISPOSAL ●... -
Page 5: Instructions For This Tool
TQ14375 Abrasive Paper 2" x #80 allowable rotation speed shown on the Abrasive TQ14376 Abrasive Paper 2" x #100 Paper is lower than the free speed of the MLS-20. TQ14377 Abrasive Paper 2" x #120 Small rotation speed of the Abrasive Paper causes... -
Page 6: Air Supply
4. AIR SUPPLY 5. OPERATION CAUTION WARNING ● Draw off drain before starting operation. If the ● Be sure to wear eye protection during operation. drain enters into the tool, it can freeze around Use a dust mask if operation is exposed to dust. the exhaust port of the tool and result in output ●... -
Page 7: Storage
5-2. Start and Stop The Hold the body, Move the switch to the ON To start, release the lock lever and grasp the throttle position. lever. You work and pressed lightly on the object to be To stop, release the throttle lever. ground Abrasive Paper. -
Page 8: Optional Parts
9. OPTIONAL PARTS A variety of Abrasive Papers are available for the MLS-20 so that you can use them according to the application. compressor. The drain, however, is condensed in the piping, and can enter into the tool mechanism, and may cause trouble. So, install an air filter, an air regulator and an oiler between the compressor and the tool.