Table of Contents
Advertisement
Quick Links
INSTRUCTION
MANUAL
<Specifications>
Maximum Operating Pressure
Air Consumption (No Load)
Rated Speed (No Load)
Standard Belt Size
Mass (Weight)
Sound Pressure Level
Sound Power Level
Vibration Level[Uncertainty K]
Thread Size of Air Inlet
*1 Based on the ISO15744 measurement standard.
*2 Based on the 3 axes combined value measurement standard of the
ISO28927-9 of the hand-held tool frequency correction vibration acceleration
effective value.
l Please read this manual carefully before you attempt to use your tool so that you may use it
l
properly and safely.
l Please keep the manual handy - so you can use it whenever necessary.
l
• Due to continuous product development/improvement the specifications and configurations in this
document are subject to change without prior notice.
Manufactured by:
NITTO KOHKI CO., LTD.
Professional Tool
Model: BB-10B
Model
MPa
m
3
/min
min
mm
kg
dB(A)
dB(A)
m/s
9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo, 146-8555, Japan
Tel : +81-3-3755-1111 Fax : +81-3-3753-8791
Pneumatic Belt Sander
BB-10B
0.6
0.2
-1
17000
10×330
(25/64"×13")
0.6
79
90
2
0.49 [0.23]
Rc 1/4
TQ15460-0 07/2018
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Nitto Kohki BABY BELTON BB-10B
Summary of Contents for Nitto Kohki BABY BELTON BB-10B
- Page 1 • Due to continuous product development/improvement the specifications and configurations in this document are subject to change without prior notice. Manufactured by: 9-4, Nakaikegami 2-chome, Ohta-ku, Tokyo, 146-8555, Japan NITTO KOHKI CO., LTD. Tel : +81-3-3755-1111 Fax : +81-3-3753-8791 TQ15460-0 07/2018...
-
Page 2: Table Of Contents
Instructions Thank you very much for your purchase of this NITTO KOHKI product. Before using your tool, please read this manual carefully so that you may use it properly to get the most out of it. Please keep the manual handy - so you can use it whenever necessary. -
Page 3: Precautions On Use (Make Sure To Follow The Instructions Given)
California Proposition 65 WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer birth defects or other reproductive harm. Some examples of these chemicals are: l Lead from lead-based paints, l Crystalline silica from bricks and cement and other masonry products, and l Arsenic and chromium from chemically-treated lumber. - Page 4 Precautions on Use Work area safety WARNING l Do not use the tool at home. This is a professional tool (industrial or work tool for business). Do not bring the tool home and use it there. l Keep the work area clean. Working in a messy work area or work table could cause an accident.
- Page 5 Handling tools WARNING l Storing the tool When the tool is not used, store the tool in a dry location. Also, store the tool out of the reach of children. For some tools, the storage temperature and humidity are specified. Store the tool in an appropriate location. l Be cautious about how the tool is carried.
- Page 6 This tool shall be inspected periodically to verify the ratings and markings. When a label/nameplate is damaged, worn or missing, contact the sales agent through which you have purchased your tool or NITTO KOHKI Co. Ltd. directly for a replacement.
- Page 7 Projectile Hazards WARNING l Be aware that failure of the workpiece or accessories, or even of the inserted tool itself can generate high- velocity projectiles. l Always wear impact-resistant eye protection while operating this tool. The grade of protection required should be assessed for each operation.
- Page 8 Precautions on Use Accessory Hazards WARNING l Disconnect the tool from the energy supply before fitting or changing the inserted tool or accessory. l Avoid direct contact with the inserted tool during and after use, as it can be hot or sharp. l Use only accessories and consumables that are the sizes and types recommended by the manufacturer of this tool;...
- Page 9 Noise Hazards WARNING l Exposure to high noise levels can cause permanent, disabling hearing loss and other problems, such as tinnitus (ringing, buzzing, whistling or humming in the ears). Therefore, risk assessment and implementation of appropriate controls for these hazards are essential. l Appropriate controls to reduce the risk can include actions such as damping materials to prevent workpieces from “ringing”.
- Page 10 When you change or adjust the tool or parts, be sure to detach the tool from the air hose. l Never touch the moving parts while in operation. l Always use the genuine Abrasive Belt for the belt sander BB-10B (Nitto Kohki Co., Ltd.).
-
Page 11: Application
1 Application This is a handheld pneumatic belt sander designed and built to perform sanding operation utilizing a abrasive belt. 2 Checking Inside the Package When you open the package box, check the contents of the package and also check for any damage that may have occurred during transportation. -
Page 12: Part Names
3 Part Names ⑨ ⑦ ② ① ⑧ ⑥ ① Abrasive Belt ② Bracket ⑤ ③ Offset Bracket ④ ④ Cover Screw ⑤ Belt Cover ③ ⑥ FR Valve ⑦ Throttle Lever ⑧ Valve Body ⑨ Air Hose... -
Page 13: Air Supply
4 Air Supply CAUTION z Remove drainage before stating work. When drainage enters the tool, the vicinity of the exhaust port freezes, which could cause a loss of power. ① ① Compressor ② Air Filter ② ③ Air Regulator ③ ④... -
Page 14: Preparation
When you change or adjust the tool or parts, be sure to detach the tool from the air hose. z Never touch the moving parts while in operation. z Always use the genuine Abrasive Belt for the belt sander BB-10B (Nitto Kohki Co., Ltd.). Start and Stop... -
Page 15: Switching The Rotating Direction And Adjusting The Rotation Speed
Switching the rotating direction and adjusting the rotation speed Switching of rotating direction Forward rotation and reverse rotation of Reverse rotation abrasive belt are switched by rotating FR valve in Forward rotation side or reverse rotation side. Forward rotation Forward Adjustment of rotation frequency rotation The rotation frequency of abrasive belt can be... -
Page 16: Adjusting The Tracking
How to operate the tool Adjusting the Tracking Loosen the Hex. Socket Set Screw by the Hex. Socket Screw Key 1.5 as shown in Fig. 6 and turn the adjusting screw with a Pan Head screwdriver so that the Abrasive Belt may run almost in the center of the Idle Pulley, then turn the Hex. -
Page 17: Relocation Of Throttle Lever
Relocation of Throttle Lever The Throttle Lever can be positioned on either side of the tool body comfortable both to right-handed or Throttle Lever left handed (southpaw) operator, as follows; Lock Ring Loosen the Hex. Socket Set Screw using the included Hex. -
Page 18: Maintenance And Inspection
7 Maintenance and Inspection Storing the tool Store the tool according to the following warnings and cautions. WARNING z When the tool is not in use, store out of the reach of children. CAUTION z When the tool is not in use, store in a place with little humidity. z After completing work, lubricate with machine oil (ISO VG-10) from the Coupler of the tool and operate a little before storing. - Page 19 Shizuoka Sales Office 15-4, Kutsunoya 6-chome, Aoi-ku, Shizuoka-shi, Shizuoka 420-0816, Japan Tel: +81-54-655-5100 (main) Fax: +81-54-264-8405 NITTO KOHKI U.S.A., INC. NITTO KOHKI (SHANGHAI) CO., LTD. Shenzhen Branch For Caplas: Tel: +1-630-924-5959 Fax: +1-630-924-1174 Tel: +86-755-8375-2185 Fax: +86-755-8375-2187 For Machine Tools: Tel: +1-630-924-9393 Fax: +1-630-924-0303 NITTO KOHKI CO., LTD.
Need help?
Do you have a question about the BABY BELTON BB-10B and is the answer not in the manual?
Questions and answers