HeatStar HSU50NG Operating Instructions And Owner's Manual

Compact unit heater for residential/commercial use
Table of Contents

Advertisement

Available languages

Available languages

Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference.
READ INSTRUCTIONS CAREFULLY: YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS.
Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow
anyone who has not read these instructions to assemble, light, adjust or operate the heater.
COMPACT UNIT HEATER
FOR RESIDENTIAL/COMMERCIAL USE
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to this manual. For assistance or additional information
consult a qualified installer, service agency or the gas supplier.
-WHAT TO DO IF YOU SMELL GAS
Ǟ DO NOT try to light appliance.
Ǟ DO NOT touch any electrical switch, do not use any phone in your building
Ǟ Leave the building immediately
Ǟ Immediately call your gas supplier from a phone remote from the building. Follow the gas suppliers
instructions
Ǟ If you cannot reach your gas supplier, call the Fire Department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
WWW.HEATSTARBYENERCO.COM
OPERATING INSTRUCTIONS
AND OWNER'S MANUAL
1-(866)-447-2197
MODEL#
HSU50NG
HSU80NG
HSU125NG
60186 REV A

Advertisement

Table of Contents
loading

Summary of Contents for HeatStar HSU50NG

  • Page 1 Installer: Leave this manual with the appliance. Consumer: Retain this manual for future reference. OPERATING INSTRUCTIONS MODEL# HSU50NG AND OWNER’S MANUAL HSU80NG HSU125NG READ INSTRUCTIONS CAREFULLY: YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS. Read and follow all instructions. Place instructions in a safe place for future reference. Do not allow anyone who has not read these instructions to assemble, light, adjust or operate the heater.
  • Page 2: Table Of Contents

    OR E-MAIL USING THE HEATSTAR WEBSITE: IGNITION CONTROL LED ..........11 WWW.HEATSTARBYENERCO.COM SERVICE ............... 12 In order to provide the best service possible HEATSTAR is WIRING DIAGRAM ............13 now giving you more ways to get in touch with us. Find FUEL CONVERSION ............14 informational videos at: PARTS LIST ..............
  • Page 3: Unit Dimensions

    UNIT DIMENSIONS 318mm 318mm (12 ½”) (12 ½”) MOUNTING SLOTS 165 mm 165mm (Typical) (6 ½”) (6 ½”) HANGING 5/16 x 3 Inches BRACKETS 70 mm 70 mm (8 x 76 mm) (2 ¾”) (2 ¾”) 25 mm (1”) 13 mm (½”) 470 mm AIR FLOW...
  • Page 4: Shipping

    SHIPPING TABLE 1 UNIT CLEARANCES The heater is completely assembled. Installation instructions, two mounting brackets (shipped loose), and a flue transition are included. Sides Access Panel Check the unit for shipping damage. The receiving party should contact the last carrier immediately if any shipping damage is found. REQUIREMENTS REQUIREMENTS –...
  • Page 5: Unit Heater Installation

    These units are certified for residential applications. For installation in combustion air are not available, the heater or another appliance will a residential garage, these units must be installed so that burners and operate in an inefficient manner, resulting in incomplete combustion ignition source are located no less than 18”...
  • Page 6 Installation Code for maximum vent and vent connector lengths. VENT TERMINATION ON SINGLE WALL VENT Horizontal run of the vent connector from the induced draft blower SINGLE WALL TERMINATION to the chimney/vent cannot exceed the values in table 2. ROOF FLASHING 4.
  • Page 7 7. Vent termination must be a minimum of 10’ (3m) from any forced E – HORIZONTAL VENTING – RESIDENTIAL air inlet (includes fresh air inlet for other appliances, such as a 1. For horizontal residential installations these units are certified as dryer).
  • Page 8 HORIZONTAL VENTING - RESIDENTIAL INSTALLATION UPWARD SLOPE INDUCED DRAFT BLOWER 12 INCHES MIN (30.5 CM) FLUE TRANSITION (PROVIDED) VENT TERMINATION CAP LISTED THIMBLE THROUGH COMBUSTION WALL CATEGORY III VENT ACCORDING TO THESE INSTALLATION INSTRUCTIONS. SLOPE: +¼ INCH FOR 1 FOOT RUN MINIMUM (1mm per 50mm) NOTE - MINIMUM HORIZONTAL LENGTH 3FT.
  • Page 9: Electrical Connections

    5. Test for spillage at the draft hood relief opening after five minutes of main burner operation. Use the flame of a match or candle, or smoke from a cigarette, cigar, or pipe. LINE VOLTAGE FIELD WIRING 6. After it has been determined that each appliance remaining UNIT connected to the common venting system properly vents when tested as outlined above, return doors, windows, exhaust fans,...
  • Page 10: Gas Connections

    LEAK CHECK WARNING Electric shock hazard. Can cause injury or death. CAUTION DO NOT use matches, candles, flame or other sources of Do not use this heater if any part has been ignition to check for gas leaks. under water. Immediately call a qualified service After gas piping is completed, carefully check all piping connections, technician to inspect the furnace and to replace (field and factory), for gas leaks.
  • Page 11: Heating Sequence Of Operation

    1. STOP! Make sure you have read and understand all of the safety do not match those described above. Refer to the trouble shooting information regarding the operation of this gas appliance. Any and sections. all service should be performed by a licensed installer 7.
  • Page 12: Service

    HIGH ALTITUDE • Clean burners as necessary. Make sure that burner heads line up properly to ensure flame crossover. Check spark gap on electrode Units may be fired at full input up to 2000 ft. (610m) above sea level. and adjust if required. The gap should be between 0.110 inch and Above 2000 ft.
  • Page 13: Wiring Diagram

    24V Power WIRING DIAGRAM DATA + 24 Vac POWER MAXIMUM LOAD NOT TO EXCEED 20VA AT 24V, CLASS 2 OPTIONAL FAN CONTROL (2) S47 USED IN 24VAC 75, 80 AND 125 ONLY HEAT 1 ANALOG NOTE - FLAME FLAME SENSOR IF ANY WIRE IN THIS APPLIANCE IS REPLACED, COMMON IT MUST BE REPLACED WITH WIRE OF LIKE SIZE,...
  • Page 14: Fuel Conversion

    FUEL CONVERSION FUEL CONVERSION INSTRUCTIONS FUEL CONVERSION Section 1: FUEL CONVERSION KITS For Converting from Natural Gas to L.P. Gas HONEYWELL KIT #393691 Fuel Conversion Part Numbers Model # BTU/HR Gas Conversion Labels HSU 50 50,000 Natural - To - LP F260163 HSU 80 80,000...
  • Page 15 If it does not, immediately contact Heatstar, Inc. for the correct kit. If they are the correct orifices, install them in the manifold using caution not to cross thread.
  • Page 16 10” 4” N.G. L.P. FIGURE 12 Step 5 Step 10 Rotate the valve/ manifold assembly back up into the burner box, When the burners light, set the manifold gas pressure by turning the making sure that all the orifices are indexed into the burners and are adjustment screw to the regulator spring that was replaced in step 6.
  • Page 17 FUEL CONVERSION Section 3: RATE TAG CONVERSION INSTRUCTIONS FIGURE 13 Step 13 Table 4 NATURAL GAS MANIFOLD PRESSURES - IN. W.C.. (KPA) Connect main electrical power, and turn main gas supply back on. ALTITUDE FT. (M) Turn up thermostat to call for heat. When the main burners light HSU 50/80/125 using soapy water check all connections thoroughly for gas leaks.
  • Page 18 REPAIR PARTS When ordering parts include the complete unit model number listed on the unit rating plate. Heatstar • Compact / Utility Heater • Model # HSU50 / HSU80 Compact Unit / Utility Heater Operating Instructions and Owner’s Manual...
  • Page 19: Parts List

    PARTS LIST SEE BACK PAGE FOR PARTS ORDERING INFORMATION REF # Description QTY 80K 60261 60261 CIRCUIT BOARD LIMIT SENSOR 60022 60021 ELECTRODE IGNITER 60139 60139 ELECTRODE SENSOR 60141 60141 BURNER 60155 60155 IGNITION LEAD 60045 60045 SENSOR LEAD 60046 60046 ORIFICE (NAT) 60049...
  • Page 20 Heatstar • Compact / Utility Heater • Model # HSU125 Compact Unit / Utility Heater Operating Instructions and Owner’s Manual...
  • Page 21 SEE BACK PAGE FOR PARTS ORDERING INFORMATION REF # Description 125K 60252 BRACKET 60253 MOUNTING PANEL-MOTOR 60254 MOUNTING PANEL-FRONT AND BACK 60255 MOUNTING PANEL-BOTTOM 60256 MOUNTING PANEL-SIDE 60265 MOUNTING PANEL-TOP HEAT EXCHANGER 60206 BRACKET-HEAT EXCHANGE 60207 FAN MOTOR 60208 FAN GUARD 60209 FAN ASSEMBLY 60210...
  • Page 22: Warranty

    This Warranty gives you specific legal rights, and you may have other rights which vary from state to state. Heatstar, Inc. reserves the right to make changes at any time, without notice or obligation, in colors, specifications, accessories, materials and models.
  • Page 23 Instalador: deje este manual con el aparato. Consumidor: conserve este manual para referencia futura. INSTRUCCIONES DE USO Y Modelo# HSU50NG MANUAL DEL USUARIO HSU80NG HSU125NG LEA CUIDADOSAMENTE LAS INSTRUCCIONES: Lea y siga todas las instrucciones. Conserve estas instrucciones en un lugar seguro para futura referencia. No permita que nadie que no haya leído estas instrucciones arme, encienda, ajuste o use el calefactor.
  • Page 24 ENVÍENOS UN MENSAJE A TRAVÉS DEL SITIO WEB DE Heatstar: REPARACIÓN .............. 34 WWW.HEATSTARBYENERCO.COM DIAGRAMA DE CABLEADO .......... 35 Con el fin de brindar el mejor servicio posible, HEATSTAR ahora le brinda más formas de comunicarse con nosotros. Encuentre CONVERSIÓN DE COMBUSTIBLE ......... 36 videos informativos en: LISTA DE PARTES ............
  • Page 25: Tamaño De La Unidad

    TAMAÑO DE LA UNIDAD 318mm 318mm (12 ½”) (12 ½”) RANURAS DE MON- 165 mm 165mm TAJE (típico) SOPORTES (6 ½”) (6 ½”) 5/16 x 3 pulgadas PARA COL- 70 mm 70 mm (8 x 76 mm) (2 ¾”) (2 ¾”) 25 mm (1”) 13 mm...
  • Page 26: Envío

    ENVÍO TABLA 1 SEPARACIONES DE LA UNIDAD El calefactor viene completamente armado. Las instrucciones de instalación, dos soportes de montaje (sueltas) y un acople para la Parte superior Costados Panel de acceso salida de combustión vienen incluidos. Inspeccione la unidad por pulg.
  • Page 27: Instalación Del Calefactor

    Estas unidades están aprobadas para uso residencial. Para la Todos los calefactores a gas requieren aire para el proceso de instalación en un garaje residencial, estas unidades deben instalarse combustión. En muchos edificios de hoy en día, existe una presión de modo que los calefactores y las fuentes de ignición se encuentren negativa en el aire interior causada por los ventiladores de escape, a no menos de 8 pies (457 mm) sobre el piso.
  • Page 28 de aire inducido del artefacto. TERMINACIÓN DE VENTILACIÓN EN VENTI- 3. Mantenga los tramos de conducto de ventilación lo más corto posible LACIÓN DE PARED SIMPLE con la cantidad mínma de codos. Consulte la Norma nacional de gas TERMINACIÓN DE PARED SIMPLE combustible (EE.UU.), ANSI Z223.1 o con la CSA B149.1 (Canadá) Norma de instalación de gas natural y propano por el recorrido y el TAPAJUNTAS DEL TECHO...
  • Page 29 5. La terminación de ventilación deberá estar a como mínimo 4 pies E – VENTILACIÓN HORIZONTAL - COMERCIAL (1,2m) por debajo o a 4 pies (1,2m) a un costado de cualquier respi- 1. Para instalaciones residenciales horizontales, estas unidades radero del sofito o ventilación debajo de aleros. están certificadas como artefactos categoría III.
  • Page 30 VENTILACIÓN HORIZONTAL - INSTALACIÓN RESIDENCIAL INCLINACIÓN HACIA ARRIBA SOPLADOR DE TIRO INDUCIDO 12 COMO MÍNIMO (30.5 CM) TRANSICIÓN DE COMBUSTIÓN (SUMINISTRADA) TAPA DE TERMINACIÓN DE GUARDACABO APROBADO A VENTILACIÓN TRAVÉS DE PARED COMBUSTIBLE VENTILACIÓN CATEGORÍA III DE ACUERDO CON ESTAS INSTRUCCIONES DE INSTALACIÓN INCLINACIÓN +¼“...
  • Page 31: Conexiones Eléctricas

    otro artefacto que no esté conectado al sistema de ventilación en común. Encienda todos los extractores de aire, como los de la cocina y el baño, para que funcionen a su máxima velocidad. No CABLEADO DE ALIMENTACIÓN encienda los extractores de aire de verano. Cierre las compuertas de los hogares.
  • Page 32: Conexión De Gas

    ADVERTENCIA VERIFICACIÓN DE FUGAS Riesgo de descarga eléctrica. Podría causar lesiones CUIDADO: NO utilice fósforos, velas, llamas u otras fuentes de ig- o la muerte. No use este calefactor si alguna de las nición para detectar fugas de gas. piezas ha estado bajo el agua. Contáctese de inmedi- Luego de completar las tuberías, revise cuidadosamente todas las ato con un técnico de mantenimiento calificado para conexiones (las de fábrica y las realizadas en el lugar) para verificar...
  • Page 33: Secuencia De Operación Del Calefactor

    1. ¡DETÉNGASE! Asegúrese de haber leído y comprendido toda la sin superponerse. Si las características de su quemador no información de seguridad acerca de la operación de este artefacto corresponden con lo mencionado anteriormente, consulte la sección de resolución de problemas. a gas.
  • Page 34: Reparación

    LUGARES MUY ALTOS y del sensor. Remueva el múltiple. Remueva la bandeja de los quemadores. Estas unidades pueden funcionar a plena entrada hasta una altitud de 2000 pies (610 m) sobre el nivel del mar. Por encima de los 2000 pies •...
  • Page 35: Diagrama De Cableado

    24V Power DIAGRAMA DE CABLEADO DATA + CARGA MÁXIMA PARA NO 24 Vac ENERGÍA EXCEDER 20VA AT 24V, CLASE 2 CONTROL DE VENTILADOR OPCIONAL (2) S47 S47 UTILIZADO EN 24VAC 75, 80 Y 125 SOLAMENTE CALOR 1 NOTA- ANALÓGICO SENSOR DE SI SE REEMPLAZA ALGÚN CABLE EN ESTE FLAME LLAMA...
  • Page 36: Conversión De Combustible

    CONVERSIÓN DE COMBUSTIBLE INSTRUCCIONES PARA CONVERSIÓN DE COMBUSTIBLE Sección 1 JUEGOS DE CONVERSIÓN DE COMBUSTIBLE Para conversión de gas natural a L.P. JUEGO HONEYWELL #393691 Número de partes del juego de conversión de combustible Model # BTU/HR HSU 50 50 000 Gas natural a LP Etiqueta de conversión de gas F260163...
  • Page 37 3. Si no coinciden, llame inmediatamente a Heatstar, Inc. para que le envíen el juego correcto. Luego de confirmar que el juego ADVERTENCIA de conversión es el correcto para el modelo de calefactor que esté...
  • Page 38 10” 4” Gas Natural Propano FIGURA 12 Paso 5 Paso 10 Gire el mecanismo de válvulas/múltiple nuevamente dentro de la caja Cuando se encienda el quemador, ajuste la presión de gas del múltiple de combustión, verificando que todos los orificios queden dentro de girando el tornillo de ajuste del resorte del regulador que reemplazó...
  • Page 39 Sección 3 INSTRUCCIONES DE CONVERSIÓN DE ETIQUETA DE VELOCIDAD FIGURA 13 Paso 13 Tabla 4 PRESIONES DEL MÚLTIPLE PARA GAS NATURAL - PULG. COL. Vuelva a conectar el suministro de energía y abra la llave de paso del AGUA (kPa) gas.
  • Page 40 PARTES DE REPARACIÓN Al ordenar partes, incluya el número completo de modelo de la unidad que aparece en la placa de especificaciones. Heatstar• Calefactor compacto/de trabajo • Modelo HSU50 / HSU80 Unidad compacta/Calefactor de trabajor Instrucciones de uso y manual del usuario...
  • Page 41: Lista De Partes

    LISTA DE PARTES: VER AL DORSO LA INFORMACIÓN PARA ORDENAR PARTES REF # Descripción CANT CANT 60261 60261 PLACA DE CIRCUITO 60022 60021 SENSOR DE LÍMITE 60139 60139 ELECTRODO ENCENDEDOR 60141 60141 SENSOR DE ELECTRODO 60155 60155 QUEMADOR 60045 60045 CONDUCTOR DE IGNICIÓN 60046 60046...
  • Page 42 Heatstar • Calefactor compacto/de trabajo • Modelo HSU125 Unidad compacta/Calefactor de trabajor Instrucciones de uso y manual del usuario...
  • Page 43 LISTA DE PARTES: VER AL DORSO LA INFORMACIÓN PARA ORDENAR PARTES REF # Description 125K CANT 60252 SOPORTE 60253 PANEL DE MONTAJE- MOTOR 60254 PANEL DE MONTAJE- FRENTE Y POSTERIOR 60255 PANEL DE MONTAJE- INFERIOR 60256 PANEL DE MONTAJE- COSTADO 60265 PANEL DE MONTAJE- SUPERIOR 60206...
  • Page 44 THIS PAGE INTENTIONALLY LEFT BLANK ESTA PÁGINA SE DEJÓ INTENCIONALMENTE EN BLANCO CETTE PAGE A ÉTÉ INTENTIONNELLEMENT LAISSÉE VIERGE Unidad compacta/Calefactor de trabajor Instrucciones de uso y manual del usuario...
  • Page 45: Garantía Limitada

    Esta Garantía le otorga derechos legales específicos, y usted puede tener otros derechos que varían de un estado a otro. Heatstar Inc. se reserva el derecho de hacer cambios en cualquier momento, sin previo aviso, en los colores, especificaciones, accesorios, materiales y modelos.
  • Page 46 Installateur: Laissez ce manuel avec l’appareil. Consommateur: Conservez ce manuel pour référence ultérieure. MANUEL DE L’UTILISATEUR ET de modèle HSU50NG INSTRUCTIONS D’OPÉRATION HSU80NG HSU125NG LIRE ATTENTIVEMENT CES INSTRUCTIONS: Lire et suivre toutes les instructions. Placer ces instructions dans un endroit sûr pour référence future. Ne pas permettre à quiconque qui n’aurait pas lu ces instructions de procéder à...
  • Page 47 Heatstar: SCHÉMA DE CÂBLAGE ..........58 WWW.HEATSTARBYENERCO.COM CONVERSION DE CARBURANT ........59 Afin d’offrir le meilleur service possible, Heatstar vous offre LISTE DES PIÈCES ............64 dorénavant plus de moyen pour nous contacter. Trouvez des GARANTIE ..............68 vidéos d’information sur: YouTube: youtube.com/heatstarTV...
  • Page 48: Dimensions De L'appareil

    DIMENSIONS DE L’APPAREIL 318mm 318mm (12 ½”) (12 ½”) FENTES POUR LE 165 mm 165mm MONTAGE (typique) (6 ½”) (6 ½”) HANGING 8 x 76 mm BRACKETS (5/16 x 3 po) 70 mm 70 mm (2 ¾”) (2 ¾”) 25 mm (1”) 13 mm (½”)
  • Page 49: Expédition

    EXPÉDITION TABLEAU 1 DÉGAGEMENTS AVEC L’APPAREIL Le radiateur est entièrement assemblé. Instructions d’installation, deux supports de montage (expédiés de manière lâche), et une transition Dessus Côtés Panneau d’accès des émanations sont compris. Vérifier l’appareil pour la présence de dommages lors de l’expédition. La partie qui fait la réception doit communiquer immédiatement avec le dernier transporteur si quelque dommage d’expédition est trouvé...
  • Page 50: Installation De L'appareil De Chauffage

    Ces appareils sont certifiés pour les applications résidentielles. Pour dans son processus de combustion. De nos jours, on trouve une toute installation dans un garage résidentiel, ils doivent être installés pression d’air négative à l’intérieur de nombreux édifices, laquelle est de sorte que les brûleurs et la source d’ignition soient localisés à...
  • Page 51 possible, avec un nombre de coude gardé au minimum. Se référer TERMINAISON SUR UN ÉVENT À SIMPLE PAROI au Code national (américain) du carburant gazeux ANSI Z223.1 ou TERMINAISON SUR UN ÉVENT À SIMPLE PAROI au Code (canadien) pour l’installation de gaz naturel et de propane SOLIN DE TOITURE CSA B149.1 pour les longueurs maximales d’évent, et pour les connecteurs d’évent.
  • Page 52 5. La terminaison d’évent doit être au minimum à 1,2 m (4 pi) au E – AÉRATION HORIZONTALE – RÉSIDENTIELLE dessous, ou à 1,2 m (4 pi) à l’horizontale, de tout dispositif de venti- 1. Pour les installations résidentielles, à l’horizontale, ces appareils lation ou d’évent d’avant-toit.
  • Page 53 AÉRATION HORIZONTALE - INSTALLATION RÉSIDENTIELLE PENTE VERS LE HAUT SOUFFLANTE À TIRAGE INDUIT MINIMUM DE 30 CM (12 PO) TRANSITION DES ÉMANATIONS (FOURNIE) COUVERCLE DE LA MANCHON D’EMBOÎTEMENT HO- TERMINAISON D’ÉVENT MOLOGUÉ AU TRAVERS DU MUR DE COMBUSTION ÉVENT DE CATÉGORIE III CONFORMÉMENT À CES INSTRUCTIONS D’INSTALLATION. PENTE : MINIMUM DE 1 /4 PO PAR PIED DE COURSE (1mm par 50mm) REMARQUE : LONGUEUR HORIZONTALE MINIMALE DE 914mm (3 PI), N’INCLUANT PAS LE COUVERCLE POUR LA TERMINAISON...
  • Page 54: Connexions Électriques

    l’immeuble et toutes les portes entre l’espace dans lequel les appareils restants sont raccordés au système de ventilation commune, et les autres espaces de l’immeuble. Mettre en marche les sécheuses et CÂBLAGE DE TERRAIN POUR L’ALIMENTATION tout appareil non-raccordé au système de ventilation commune. Mettre en marche tout ventilateur d’évacuation, comme des hottes APPAREIL de cuisine et des ventilateurs d’évacuation de salle de bain, de sorte...
  • Page 55: Raccordement Du Gaz

    VÉRIFICATION DE FUITE AVERTISSEMENT MISE EN GARDE NE PAS utiliser d’allumette, de chandelle, de Risque de choc électrique. Peut causer des blessures flamme ou toute autre source d’ignition pour vérifier une fuite de gaz. ou la mort. Ne pas utiliser ce radiateur si quelque partie a été...
  • Page 56: Séquence D'opération Du Chauffage

    1. ARRÊT! S’assurer d’avoir lu et bien compris toutes les informations 7. Le contrôle d’ignition mettra en marche le ventilateur, environ 45 de sécurité concernant le fonctionnement de cet appareil au gaz. secondes après avoir établi l’ignition. Tout service doit être fait par un installateur qualifié et licencié. 8.
  • Page 57: Service

    HAUTE ALTITUDE • Nettoyer les brûleurs au besoin. S’assurer que les têtes de brûleur s’alignent correctement pour assurer le bon croisement de flamme. Les appareils peuvent être allumés à leur pleine puissance à des altitudes Vérifier l’écartement des électrodes et l’ajuster si requis. L’écartement doit pouvant atteindre les 610 m (2 000 pi) au-dessus du niveau de la mer.
  • Page 58: Schéma De Câblage

    24V Power SCHÉMA DE CÂBLAGE DATA + CHARGE MAXIMALE NE DOIT PAS 24 Vac ENERGIE EXCÉDER 20 VA À 24 V, CLASSE 2 CONTRÔLE FACULTATIF DU VENTILATEUR (2) S47 UTILISÉ EN 24VAC 75, 80 ET 125 SEULEMENT CHALEUR 1 analogique NOTE CAPTEUR DE FLAME...
  • Page 59: Conversion De Carburant

    CONVERSION DE CARBURANT INSTRUCTIONS POUR LA CONVERSION DE CARBURANT Section 1 ENSEMBLES DE CONVERSION DE CARBURANT Pour la conversion de gaz naturel à GPL ENSEMBLE HONEYWELL N 393691 Numéros de pièce pour la conversion de carburant de modèle BTU/HR Étiquette de conversion de gaz HSU 50 50,000 Naturel - à...
  • Page 60 3. S’il ne correspond pas, communiquer immédiatement avec Heatstar, Inc. pour obtenir le bon jeu. Après avoir confirmé que le jeu de ressort est correct pour le modèle de AVERTISSEMENT radiateur à...
  • Page 61 10” 4” Gaz naturel FIGURE 12 Étape 5 Étape 10 Gire el mecanismo de válvulas/múltiple nuevamente dentro de la caja Lorsque les brûleurs s’allument, régler la pression du gaz au collecteur, de combustión, verificando que todos los orificios queden dentro de en tournant la vis d’ajustement sur le ressort du régulateur qui a los quemadores y que no queden atrapados en el anillo de fijación été...
  • Page 62 Section 3 CONVERSION DE L’ÉTIQUETTE DE CLASSIFICATION FIGURE 13 Étape 13 Tableau 4 PRESSION DE GAZ NATUREL AUX COLLECTEURS - POUCES DE COLONNE D’EAU (KPA) Brancher l’alimentation électrique principale, et remettre l’alimentation ALTITUDE EN PIEDS (M) principale en gaz. Monter le réglage du thermostat pour une demande HSU 50/80/125 0 à...
  • Page 63 THIS PAGE INTENTIONALLY LEFT BLANK ESTA PÁGINA SE DEJÓ INTENCIONALMENTE EN BLANCO CETTE PAGE A ÉTÉ INTENTIONNELLEMENT LAISSÉE VIERGE Radiateur Compact Manuel de l’utilisateur et instructions d’opération...
  • Page 64: Liste Des Pièces

    PIÈCES POUR RÉPARATION Lors des commandes de pièces, inclure le numéro de modèle complet de l’appareil, tel qu’indiqué sur la plaque signalétique de l’appareil. Heatstar • Radiateur compact • No de modèle HSU 50/80 Radiateur Compact Manuel de l’utilisateur et instructions d’opération...
  • Page 65 LISTE DES PIÈCES VOIR LA PAGE DE COUVERTURE ARRIÈRE POUR L’INFORMATION DE COMMANDE DE PIÈCE de réf Description Qté 80K Qté 60261 60261 PLAQUETTE DE CIRCUIT 60022 60021 SONDE DE LIMITE 60139 60139 ÉLECTRODE D’IGNITION 60141 60141 DÉTECTEUR D’ÉLECTRODE 60155 60155 BRÛLEUR 60045...
  • Page 66 Heatstar • Radiateur compact • No de modèle # HSU125 Radiateur Compact Manuel de l’utilisateur et instructions d’opération...
  • Page 67 LISTE DES PIÈCES VOIR LA PAGE DE COUVERTURE ARRIÈRE POUR L’INFORMATION DE COMMANDE DE PIÈCE No de réf. Description 125K Qté 60252 SUPPORT 60253 PANNEAU DE MONTAGE- MOTEUR 60254 PANNEAU DE MONTAGE- AVANT ET ARRIÈRE 60255 PANNEAU DE MONTAGE- BAS 60256 PANNEAU DE MONTAGE- CÔTÉ...
  • Page 68: Garantie

    état/province à l’autre. Heatstar, Inc., se réserve le droit de faire des changements en tout temps, sans préavis ni obligation, dans les couleurs, les spécifications, les accessoires, les matériaux et les modèles ENREGISTREMENT DE VOTRE PRODUIT : Nous vous remercions pour votre achat.

This manual is also suitable for:

Hsu80ngHsu125ng

Table of Contents