Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Skyrc NC2200
Summary of Contents for Skyrc NC2200
- Page 1 SK-100181 AA/AAA NiMH/NiCD Battery Charger & Analyzer Instruction Manual v 1.0...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION IN THE BOX PRECAUTIONS FEATURES SPECIFICATIONS CHARGING CURRENT AUTOMATIC ADJUSTED MANUALL Y VIEW THE DISPLA YED INFO BATTERY KNOWLEDGE FIVE WORKING MODES USING THE CHARGER WORKING MODES LED INDICATOR EXPLAINED RESCUE BATTERIES DISPLA YED INFORMATION & ICONS SKYCHARGER APP OPERATION LIABILITY EXCLUSION WARRANTY AND SERVICE... -
Page 3: Introduction
Turbo(fast charge), Charge, Discharge, Refresh & Analyze, Break-in. With four independent AA/AAA slots, NC2200 can charge up to 4 batteries at once, so you can quickly power your electronic devices. The working current can be set from 0.2A up to 2.2A based on different battery capacities. - Page 4 SKYRC NC2200 Instruction Manual Slot Button Enter Button Turbo Button Up Button Down Button Status LED Indicator VA screen 12V DC Jack Micro USB Port Anti-Skid Pads SKYRC NC2200...
-
Page 5: Precautions
SKYRC NC2200 Instruction Manual PRECAUTIONS Never charge batteries other than NiMH or NiCD. Please read the battery's manual to ensure it can accept the programmed charge/discharge rates. Never expose the unit to rain or moisture to avoid fire. Never use the charger if it appears damaged. -
Page 6: Specifications
SKYRC NC2200 Instruction Manual Auto-start within ten seconds once batteries are inserted. Adjust current automatically based on the battery resistance detected. Ez-setup: long-press to apply the same setting to all slots after setting for one slot. The wide-viewing VA screen enables super-high static contrast ratios for impressive stunning visioning. -
Page 7: Charging Current Automatic Adjusted
SKYRC NC2200 Instruction Manual CHARGING CURRENT AUTOMATIC ADJUSTED The internal resistance of the battery usually increases as it is used. When the battery is used for a long time, its internal resistance will increase. The internal resistance consumes part of the electric energy when charging and causes the battery to heat up at the same time. - Page 8 SKYRC NC2200 Instruction Manual Battery Capacity mAh (milliampere/hour) = discharge (milliampere) x discharging time (hour) For example, if you insert 2400mAh battery into an appliance which consumes 50 milliampere current continuously, the operating time of the appliance will be around 48 hours.
- Page 9 SKYRC NC2200 Instruction Manual AA Batteries Battery Capacity(mAh) Charge Rate(mA) Discharge Rate(mA) 1800 1800 2200 2000 2400 2000 2600 2000 2700 2000 Battery Matching Most electronic devices usually require two or more batteries to be used together. In this circumstance, the overall performance of power will be limited by the worst battery.
-
Page 10: Five Working Modes
SKYRC NC2200 Instruction Manual FIVE WORKING MODES The charger comes with five working modes, each of which will be used under the different situations below. Scenario Mode Fast charge with a large current of 2.2A for the batteries that TURBO are needed urgently. -
Page 11: Using The Charger
Autostart: The charger will start charging automatically with the CHARGE mode and 1000mA of charge rate as default if no operation within ten seconds after the battery is inserted. NC2200 will start working automatically to the last remembered setting if the charger worked once and its power uninterrupted. - Page 12 SKYRC NC2200 Instruction Manual Short-press the buttons to select the desired discharge rate when "SET DISCHARGE RATE" is displayed and click the button to start discharging. Note: If you plan to apply this setting to all the rest slots, PRESS & HOLD the button for two seconds to start charging.
- Page 13 SKYRC NC2200 Instruction Manual Select working rate Press ENTER to start 5, The LED indicator will be solid red during the charging process. Note: During charging or discharging, the batteries' heating-up is normal. An audible faint may also occur. 6, The LED indicator will be solid green after charging is completed.
-
Page 14: Working Modes
SKYRC NC2200 Instruction Manual WORKING MODES CHARGE MODE Please refer to the BATTERY KNOWLEDGE on page 6 to select an appropriate rate to charge the battery by the selected charge rate. Useful when the battery needs to be recharged without determining the capacity. - Page 15 SKYRC NC2200 Instruction Manual To start the TURBO CHARGE mode 1, Press and hold the button for five seconds to start the TURBO mode for those slots being in the charging process. 2, The LED indicator will be solid red during the charging process.
- Page 16 SKYRC NC2200 Instruction Manual The actual amount charged in the last cycle can be viewed on the charger. Applicable to those batteries not performing well and determine the actual capacity of the battery. To start the REFRESH & ANALYZE mode.
-
Page 17: Led Indicator Explained
SKYRC NC2200 Instruction Manual This process is also well-known as BATTERY FORMATTING and applicable to the batteries that cannot be rescued by the REFRESH & ANALYZE mode. The mode requires 39-45 hours to complete. To start the BREAK-IN mode. 1, Insert the batteries into the slots. -
Page 18: Rescue Batteries
SKYRC NC2200 Instruction Manual RESCUE BATTERIES If the batteries are still not performing well after trying all the modes as in the manual, refer to the battery rescue steps below: 1, Use the REFRESH & ANALYZE mode once to three times. - Page 19 SKYRC NC2200 Instruction Manual Elapsed Time This is the time elapsed for a particular routine such as charging, discharging, or rest in the program. Battery Voltage This is the value above "V" which means the battery voltage. If the battery is measured with a multimeter during charing, the reading may differ from what the charger shows.
-
Page 20: Skycharger App Operation
SKYRC NC2200 Instruction Manual SKYCHARGER APP OPERATION The charging graph and firmware upgrading can be accessible with the SkyCharger app if you connect the optional Bluetooth Dongle. *The optional Bluetooth Dongle(SK-600135)part is sold separately. Bluetooth Dongle is based on the BLE(Bluetooth Low Energy) that it can only be accessible by the SkyCharger app! Please be reminded: NEVER try to connect Bluetooth Dongle via Phone's>Set-... - Page 21 SKYRC NC2200 Instruction Manual • Enable Bluetooth on your mobile device. Launch the SkyCharger app. Select the device found. View the charging info. Click details to view the Click the battery icon to The graph can be zoomed charging graph.
- Page 22 Click back for details page. Click Version to check if any newer firmware; if yes, click OK to upgrade. SKYRC NC2200...
-
Page 23: Liability Exclusion
This charger is designed and approved exclusively for use with the types of the battery stated in this Instruction Manual. SkyRC accepts no liability of any kind if the charger is used for any purpose other than that stated. We are unable to ensure that you follow the instructions supplied with the charger, and we have no control over the methods you employ for using, operating and maintaining the device. - Page 24 If you have any question about this document, please contact SkyRC by sending a message to info@skyrc.com All Rights Reserved. Manufactured by SKYRC TECHNOLOGY CO., LTD. www.skyrc.com RoHS 2021 SkyRC Technology Co., Ltd. All Rights Reserved. [Version 1.0] 7504-1510-01...