Nominal Data; Technical Features; Mounting Data; Transport And Storage Conditions - ebm-papst W2E200-HK38-01 Operating Instructions Manual

W2E200-HK38-01

3.2 Nominal data

Motor M2E068-BF
Phase 1~
Nominal voltage / VAC 230
Frequency / Hz 50
Type of data definition
fa
Valid for approval / CE
standard
Speed (rpm) / min -1
2550
Power input / W 64
Current draw / A 0.29
Motor capacitor / µF 1.5
Capacitor voltage / VDB 450
Capacitor standard
S0 (CE)
Max. back pressure / Pa 80
Min. ambient -25
temperature / °C
Max. ambient 55
temperature / °C
Starting current / A
0.55
ml = Max. load · me = Max. efficiency · fa = Running at free air
cs = Customer specs · cu = Customer unit
Subject to alterations

3.3 Technical features

Mass
2.1 kg
Size 200 mm
Motor size 68
Surface of rotor Coated in black
Material of blades Sheet steel, coated in black
Material of wall ring
Die-cast aluminium
Number of blades 7
Direction of air flow V
Direction of rotation Counter-clockwise, seen on rotor
Type of protection IP44; Depending on installation and
position
Insulation class "B"
Humidity (F) / H0 - dry environment
environmental
protection class (H)
Mounting position any
Condensation None
drainage holes
Operation mode S1
Motor bearing Ball bearing
Touch current acc. < 0.75 mA
IEC 60990 (measuring
network Fig. 4, TN
system)
Electrical connection Via terminal strip, capacitor connected
Motor protection Thermal overload protector (TOP) wired
internally
Cable exit Variable
Protection class I (if protective earth is connected by
customer)
Motor capacitor S0
according to EN 60252-
1 in safety protection
class
Item no. 10760-5-9970 · ENG · Revision 203512 · Release 2019-04-29 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Product conforming
to standard
Approval
1~
230
60
fa
; Use the device in accordance with its protection type.
CE
Notes on surface quality
2800
The surfaces of the products conform to the generally applicable industrial
80
standard. The surface quality may vary during the production period.
0.35
Strength, dimensional stability and dimensional accuracy are not affected
1.5
by this.
450
The colour pigments of the paints used react perceptibly to UV light over
S0 (CE)
the course of time. This does not however have any influence on the
95
technical properties of the products. To prevent the formation of patches
-25 and fading, the product is to be protected against UV radiation. Changes
in colour are not a reason for complaint and are not covered by the
warranty.
65

3.4 Mounting data

0.54
For depth of screw, see chapter 3.1 Product drawing
Strength class for
mounting screws
; Secure the mounting screws against accidentally coming loose (e.g.
Any further mounting data required can be taken from the product
drawing or Section chapter 4.1 Connecting the mechanical system.

3.5 Transport and storage conditions

Max. permissible
ambient motor temp.
(transp./ storage)
Min. permissible
ambient motor temp.
(transp./storage)
EN 60335-1; CE
CCC; EAC; UL 1004-3; CSA C22.2
no. 113; VDE
For cyclic speed loads, note that the rotating parts of the device
are designed for maximum one million load cycles. If you have
specific questions, contact ebm-papst for support.
8.8
by using self-locking screws).
+ 80 °C
- 40 °C