Table of Contents
Advertisement
TILE MATRIX MEM
When "INPUT" is selected, TILE MATRIX setting is applied to each signal input.
POWER ON DELAY
Adjusts the delay time between being in "standby" mode and entering "power on" mode.
"POWER ON DELAY" can be set between 0 and 50 seconds.
POWER INDICATOR
Turns ON or OFF the LED located at the front of the monitor.
If "OFF" is selected, LED will not light when the LCD monitor is in active mode.
EXTERNAL CONTROL
CONTROL
Selects the control interface, RS-232C or LAN.
LAN RESET
Resets the LAN settings.
ID=ALL REPLY
When controlling the monitor externally, select if the communication command, which specifies
destination equipment ID (ALL or GROUP ID), is replying or not. When you need reply, please
select "ON".
If you connect the multiple monitors that are daisy-chained from second monitor by RS-232C,
you need to select "OFF" from second monitor.
MAC ADDRESS
Displays the MAC ADDRESS.
LAN SETTING
When you use this function, EXTERNAL CONTROL should be "LAN".
NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN
SETTING is applied.
DHCP
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
NOTE: Consult your network administrator for the IP address when "ENABLE" is selected for
[DHCP].
IP ADDRESS
Set your IP address of the network connected to the monitor when "DISABLE" is selected for
[DHCP].
SUBNET MASK
Set your subnet mask number of the network connected to the monitor when "DISABLE" is
selected for [DHCP].
DEFAULT GATEWAY
Set your default gateway of the network connected to the monitor when "DISABLE" is selected
for [DHCP].
DNS PRIMARY
Set your primary DNS settings of the network connected to the monitor.
DNS SECONDARY
Set your secondary DNS settings of the network connected to the monitor.
SETTING COPY
In a daisy chain scenario, select the OSD menu categories that you want to copy over to the
other monitor.
NOTE: When you use this function, EXTERNAL CONTROL should be "RS-232C". This function
resets to default when power is off. This function has a limit depending on the cable you use.
COPY START
Select "YES" and press the SET button to start copying.
ALL INPUT
All input terminals settings are copied when you select this item. Default is off.
RESET
Resets "MULTI DISPLAY" options back to factory settings except LAN SETTING and TILE
MATRIX MEM.
DISPLAY PROTECTION
POWER SAVE
If AUTO STANDBY is in OFF mode, POWER SAVE must be turned ON for the display to
enter the suspend power saving mode when an active signal is not present. The monitor will
automatically recover to ON state when a signal is reapplied.
POWER SAVE
Sets how long the monitor waits to go into power save mode after the signal is lost.
Note: When connecting DVI, the display cards might not stop sending the digital data even
though the image might have disappeared. If this occurs the monitor will not switch into power
management mode.
AUTO STANDBY
ON: Monitor automatically goes into OFF mode 10 minutes after signal is lost.
OFF: Monitor does not automatically go into OFF mode even after signal is lost.
NOTE: This function is disabled when RGB, VIDEO or OPTION POWER are enabled.
AUTO STANDBY will not allow the monitor to turn on after a signal is reapplied. The monitor
would need to receive a Power ON signal via the remote control, the control buttons RS-232C or
LAN to show an image again.
HEAT STATUS
Displays status of the FAN, BACKLIGHT and TEMPERATURE.
FAN CONTROL
Cooling fan reduces the temperature of the display to protect from overheating.
If "AUTO" is selected, you can adjust the start temperature of the cooling fan and fan speed.
English-24
COMMON
0 Sec.
ON
RS-232C
-
OFF
-
DISABLE
192.168.0.10
255.255.255.0
192.168.0.1
0.0.0.0
0.0.0.0
NO
-
OFF
ON
-
AUTO
Advertisement
Table of Contents
