Page 1: Table Of Contents
2004 Oldsmobile Silhouette Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-3 Rear Seats ... 1-8 Safety Belts ... 1-22 Child Restraints ... 1-46 Air Bag Systems ... 1-70 Restraint System Check ... 1-78 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Oldsmobile Division whenever it appears in this manual. Please keep this manual in your vehicle, so it will be there if you ever need it when you’re on the road.
Page 3 Safety Warnings and Symbols You will ﬁnd a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this book you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 5 These are some examples of symbols you may ﬁnd on your vehicle:...
Page 6 NOTES...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ...1-3 Manual Seats ...1-3 Six-Way Power Seats ...1-4 Eight-Way Power Seats ...1-4 Heated Seats ...1-5 Reclining Seatbacks ...1-6 Head Restraints ...1-7 Rear Seats ...1-8 Rear Seat Operation ...1-8 Flip and Fold Feature ...1-8 Split Bench Seats ...1-9 Captain Chairs ...1-14 Stowable Seat ...1-19 Safety Belts ...1-22...
Page 8 Section 1 Air Bag Systems ...1-70 Where Are the Air Bags? ...1-72 When Should an Air Bag Inﬂate? ...1-75 What Makes an Air Bag Inﬂate? ...1-75 How Does an Air Bag Restrain? ...1-76 What Will You See After an Air Bag Inﬂates? ...1-76 Servicing Your Air Bag-Equipped Vehicle ...1-78 Seats and Restraint Systems Restraint System Check ...1-78...
Page 9: Front Seats
Front Seats Manual Seats Use the lever located on the front of the seat to adjust the seat forward or rearward. Pull up the lever to unlock the seat. Slide the seat to where you want it and release the lever. CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle...
Page 10: Six-Way Power Seats
Six-Way Power Seats The six-way power seat control is located on the outboard side of the driver’s front seat. • Move the front of the control up or down to adjust the front portion of the cushion up or down. •...
Page 11: Heated Seats
Heated Seats Your vehicle may have this feature. If it does, the heated seat switches are located in the instrument panel switchbank. This feature will heat the lower cushions and lower back of the driver’s and front passenger’s seats for added comfort. The left switch is for the driver’s seat and the right switch is for the front passenger’s seat.
Page 12: Reclining Seatbacks
Reclining Seatbacks To adjust a manual seatback, pull up on the lever located on the outboard side of the driver’s or front passenger’s seat. It is easier to recline the seat if you lean forward, taking your weight off the seatback. If your vehicle has the eight-way power seats, there is a power recliner.
Page 13: Head Restraints
CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because it won’t be against your body.
Page 14: Rear Seats
Rear Seats Rear Seat Operation The rear seats in your vehicle have levers and straps used to adjust, remove, and reinstall the seats. By using the levers and straps in the correct order, you can easily remove the seats from the vehicle. When you put the seats back in the vehicle, follow the label on the back of the seat for proper location.
Page 15: Split Bench Seats
Split Bench Seats If you have the third row split bench seat, the seatbacks can be folded forward or reclined individually and the seats can be removed individually. Folding or Reclining the Seatbacks CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash.
Page 16: Removing The Split Bench Seat
Removing the Split Bench Seat Make sure the seatback is in the upright position. 1. Lift the seatback recliner lever or pull the nylon strap on the back of the seat to fold the seatback forward. 2. From behind the bench seat, pull the nylon strap at the center of the base of the seat to release the rear latches from the ﬂoor pins.
Page 17: Replacing The Split Bench Seat
Replacing the Split Bench Seat CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. CAUTION: A seat that isn’t locked into place properly can move around in a collision or sudden stop.
Page 18 1. Squeeze the angled bar toward the solid crossbar while placing the front hooks of the bench seat onto the front two ﬂoor pins. 1-12 2. Make sure the bench seat is angled so that the front hooks clear the ﬂoor pins. If the front legs are not attached correctly, the rear legs will not attach to the rear set of ﬂoor pins.
Page 19 If the front latches are not attaching correctly, check that the seat is in the full rear position. 3. Firmly push the rear hooks onto the rear ﬂoor pins by pushing down on the rear of the seat. 4. Try to raise the seat to check that it is locked down. 5.
Page 20: Captain Chairs
Captain Chairs If your vehicle has captain’s chairs, the chairs and seatbacks can be adjusted forward or rearward. Adjusting the Captain’s Chairs (Second Row) The second row captain’s chairs can be adjusted forward or rearward. There are two adjustment levers on each seat. One is located below the center, in front of the seat.
Page 21 To recline the seatback, lift up on the recliner lever, located on the outboard side of the seat. Use the recliner lever to move the seatback to the desired position. It is easier to raise or lower the seatback if you lean forward, taking the weight off the seatback.
Page 22 Removing the Captain’s Chairs 2. The seat can then be lifted off the front ﬂoor pins and removed from the vehicle. 1. Pull the nylon strap behind the chair to release the rear hooks from the ﬂoor pins. 1-16...
Page 23: Replacing The Captain's Chairs
Replacing the Captain’s Chairs CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. CAUTION: A seat that isn’t locked into place properly can move around in a collision or sudden stop.
Page 24 1. Hook the front latches over the front ﬂoor pins. 1-18 2. Push the rear of the seat down to lock the rear latches onto the rear set of ﬂoor pins. 3. Push and pull on the seat to be sure it is properly attached.
Page 25: Stowable Seat
Stowable Seat Your vehicle may have a stowable seat. The stowable seat is a full bench seat and comes with the convenience center. See Convenience Center on page 2-58 for more information. The stowable seat can be removed and replaced, or with the seatback folded, it can lie ﬂush with the convenience center.
Page 26: Removing The Stowable Seat
Removing the Stowable Seat 1. Remove the convenience center, if it is in the vehicle. See Convenience Center on page 2-58 for more information. 2. Make sure all items are off of the stowable seat. 3. If the seatback is down, put the seatback in its upright position before removing the seat.
Page 27: Replacing The Stowable Seat
Replacing the Stowable Seat CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked. CAUTION: A seat that isn’t locked into place properly can move around in a collision or sudden stop.
Page 28: Safety Belts
Make sure the seat is in its upright position before beginning this procedure. 1. Place the front hooks of the seat onto the front ﬂoor pins in the third row. To do this, the seat will need to be angled so the front hooks clear the ﬂoor pins. If the front legs are not attached correctly, the rear legs will not attach to the rear set of ﬂoor pins.
Page 29 CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 30: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it’s just a seat on wheels. 1-24...
Page 31 Get it up to speed. Then stop the vehicle. The rider doesn’t stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-25...
Page 32 or the instrument panel... 1-26 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense.
Page 33: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You could be — whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
Page 34: Driver Position
Driver Position This part describes the driver’s restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats”...
Page 35 5. To make the lap part tight, pull down on the buckle The lap part of the belt should be worn low and snug on end of the belt as you pull up on the shoulder belt. the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 36: Shoulder Belt Height Adjuster
Shoulder Belt Height Adjuster Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. 1-30 To move it down, push down on the button and move the height adjuster to the desired position. You can move the adjuster up just by pushing up on the shoulder belt guide.
Page 37 What’s wrong with this? The shoulder belt is too loose. It won’t give nearly as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body.
Page 38 What’s wrong with this? The belt is buckled in the wrong place. 1-32 CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 39 What’s wrong with this? The belt is over an armrest. CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 40 What’s wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-34 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 41 What’s wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 42: Safety Belt Use During Pregnancy
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 43: Center Passenger Position
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 44: Lap Belt
Lap Belt If your vehicle has a third row rear bench seat, someone can sit in the center position. When you sit in the center position of the bench seat, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt.
Page 45: Rear Seat Passengers
Rear Seat Passengers It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who are not safety belted can be thrown out of the vehicle in a crash.
Page 46 2. Push the latch plate into the buckle until it clicks. In the third row, if the belt stops before it reaches the buckle, tilt the latch plate and keep pulling until you can buckle it. Third Row Outside Passenger Position Pull up on the latch plate to make sure it is secure.
Page 47 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 48 To unlatch the belt, just push the button on the buckle. 1-42 Rear Safety Belt Comfort Guides for Children and Small Adults Rear safety belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for smaller adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
Page 49 1. Remove the guide from its storage pocket on the 2. Place the guide over the belt and insert the side of the seatback. two edges of the belt into the slots of the guide. 1-43...
Page 50 3. Be sure that the belt is not twisted and it lies ﬂat. The guide must be on top of the belt. 1-44 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-39 . Make sure that the shoulder belt crosses the shoulder.
Page 51: Safety Belt Pretensioners
Safety Belt Pretensioners Your vehicle has safety belt pretensioners. You’ll ﬁnd them on the buckle end of the safety belts for the driver and right front passenger. They help the safety belts reduce a person’s forward movement in a moderate to severe crash in which the front of the vehicle hits something.
Page 52: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-46 If you have the choice, a child should sit next to a window so the child can wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 53 CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck?
Page 54: Infants And Young Children
1-48 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 55 Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint. CAUTION: People should never hold a baby in their arms while riding in a vehicle.
Page 56 1-50 CAUTION: Children who are up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants.
Page 57 For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards.
Page 58: Child Restraint Systems
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ﬂat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 59 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 60 How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 61: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We, therefore, recommend that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 62: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 63 Top Strap Anchor Location Don’t use a child restraint that requires a top strap in the right front passenger’s position because there’s no place to anchor the top strap. Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed.
Page 64 Third Row (50/50) An anchor bar for a top strap is located at the rear of the seat cushion for each second and third row outboard seating position. 1-58 Third Row (Stowable Seat) The anchor bar for the stowable bench seat is located on the passenger’s side of the crossbar.
Page 65 Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will ﬁnd anchors (A) in both second row captain’s chairs. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors (A, B) and child restraint attachments to secure the restraints.
Page 66 In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. 1-60 To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback.
Page 67: Securing A Child Restraint Designed For The Latch System (Rear)
Securing a Child Restraint Designed for the LATCH System (Rear) 1. Find the LATCH anchorages for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2. Put the child restraint on the seat. 3.
Page 68 For vehicles with a full bench seat in the third row, there is no top strap anchor in the driver’s side position. Do not secure a child seat in this position if a national or local law requires that the top strap be anchored, or if the instructions that come with the child restraint say that the top strap must be anchored.
Page 69 3. Buckle the belt. Make sure the release button is 4. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-63...
Page 70 1-64 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 71 Securing a Child Restraint in a Center Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-59 . See Top Strap on page 1-56 if your child restraint has one. If your child restraint does not have the LATCH system, you’ll be using the lap belt to secure a child seat in this position.
Page 72 3. Run the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-66 5.
Page 73: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-59 . See Top Strap on page 1-56 if the child restraint has one. Your vehicle has a front passenger air bag.
Page 74 3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
Page 75 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 76: Air Bag Systems
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has four air bags – a frontal air bag for the driver, another frontal air bag for the right front passenger, a side impact air bag for the driver, and another side impact air bag for the right front passenger.
Page 77 CAUTION: (Continued) The side impact air bags for the driver and right front passenger are designed to inﬂate only in moderate to severe crashes where something hits the side of your vehicle. They are not designed to inﬂate in frontal, in rollover or in rear crashes.
Page 78: Where Are The Air Bags
CAUTION: Anyone who is up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its air bag system is designed for them.
Page 79 The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. The driver’s side impact air bag is in the side of the driver’s seatback closest to the door. 1-73...
Page 80 The right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door. 1-74 CAUTION: If something is between an occupant and an air bag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 81: When Should An Air Bag Inﬂate
When Should an Air Bag Inﬂate? The driver’s and right front passenger’s frontal air bags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact speed is above the system’s designed “threshold level.”...
Page 82: How Does An Air Bag Restrain
How Does an Air Bag Restrain? In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. In moderate to severe side collisions, even belted occupants can contact the inside of the vehicle.
Page 83 CAUTION: (Continued) the vehicle should get out as soon as it is safe to do so. If you have breathing problems but can’t get out of the vehicle after an air bag inﬂates, then get fresh air by opening a window or a door.
Page 84: Restraint System Check
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems.
Page 85: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 86 NOTES 1-80...
Page 87: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-4 Remote Keyless Entry System Operation ...2-5 Doors and Locks ...2-9 Door Locks ...2-9 Power Door Locks ...2-11 Last Door Closed Locking ...2-12 Programmable Automatic Door Locks ...2-12 Lockout Protection ...2-13 Leaving Your Vehicle ...2-13 Dual Sliding Doors ...2-13 Power Sliding Door (PSD) ...2-17 Liftgate ...2-21...
Page 88 Section 2 Storage Areas ...2-51 Glove Box ...2-51 Cupholder(s) ...2-52 Compact Overhead Console ...2-52 Overhead Console ...2-53 Front Seat Storage Net ...2-54 Luggage Carrier ...2-54 Rear Storage Area ...2-56 Convenience Net ...2-56 Convenience Center ...2-58 Features and Controls Vehicle Personalization ...2-60 Entering Programming Mode ...2-61 Delayed Illumination and Exit Lighting ...2-61 Automatic Door Locks ...2-62...
Page 89: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed. Do not leave the keys in a vehicle with children.
Page 90: Remote Keyless Entry System
® Your vehicle has the PASS-Key system. The key has a transponder in the key head that matches a decoder in the vehicle’s steering column. If a replacement key or any additional key is needed, you must purchase this key from your dealer. The key will have PK3 stamped on it.
Page 91: Remote Keyless Entry System Operation
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: •...
Page 92: Remote Alarm
With the content theft-deterrent system, the UNLOCK button on the remote keyless entry transmitter will disarm the system. See Content Theft-Deterrent on page 2-26 for more details. When you use your remote keyless entry transmitter to unlock your vehicle or to operate the power sliding door(s), the parking lamps will ﬂash to let you know the command was received.
Page 93: Matching Transmitter(S) To Your Vehicle
If the power sliding door(s) is locked, ﬁrst unlock all doors, then press the van symbol to open the power sliding door(s). The parking lamps will ﬂash when the right button with the van symbol is pressed and they will not ﬂash when the left button with the van symbol is pressed.
Page 94: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about three years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Page 95: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 96 To unlock the driver’s door from the outside with the key, insert the key and turn it toward the front of the vehicle. If your vehicle has power door locks, you may be able to unlock all of the doors and the liftgate by inserting the key, turning it toward the front of the vehicle, and holding it there for one second.
Page 97: Power Door Locks
Power Door Locks From the inside, press the front of the power door lock switch, located on either front door, to unlock all doors and the liftgate. With the content theft-deterrent system, the power door lock switch will not unlock the doors until the system is disarmed.
Page 98: Last Door Closed Locking
Last Door Closed Locking The last door closed locking feature will delay the power locking of the doors and liftgate for up to ﬁve seconds after exiting the vehicle, when the power door lock switch or the lock button on the remote keyless entry transmitter is used to lock your vehicle.
Page 99: Sliding Door Delayed Locking
Sliding Door Delayed Locking If either sliding door is open when you use the power door locks to lock the vehicle, the sliding door that is open will not lock. Normally the last door closed locking feature will be used to lock the sliding door after it has been closed.
Page 100: Sliding Door Lock
Sliding Door Lock 2-14 CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut be sure to hold it open until everyone is clear of the door, and only then allow it to slowly close.
Page 101: Sliding Door Security Lock
Lock either sliding door from inside the vehicle by moving the manual lever down. Unlock it by moving the lever up. With the power door locks, the sliding door lock has a delay feature. See Power Door Locks on page 2-11 and Vehicle Personalization on page 2-60 .
Page 102 If your vehicle has the power sliding door(s), you can override the security lock by pressing either power door lock switch while the power sliding door override switch(es) is turned off. If the power sliding door override switch(es) is turned on, the power sliding door(s) cannot be opened from the inside while the sliding door security lock is in use.
Page 103: Power Sliding Door (Psd)
Power Sliding Door (PSD) If your vehicle has this feature, you can open and close the sliding door(s) using the switches inside of your vehicle. You can also operate the power sliding door(s) with your remote keyless entry transmitter. See Remote Keyless Entry System on page 2-4 .
Page 104 If you have the dual sliding doors, your vehicle has these switches. The left switch is for the driver’s side power sliding door and the right switch is for the passenger’s side sliding door. The power sliding door and the power sliding door override is one switch.
Page 105 CAUTION: If you shift the transaxle out of PARK (P) and accelerate before the power sliding door latches closed, the door may reverse to the open position. A child or others could fall out of the vehicle and be injured. Always make sure the power sliding door is closed and latched before you drive away.
Page 106 2-20 CAUTION: If your vehicle is facing downward on a steep grade (15 percent or more), the door may not stay open and could slam shut, possibly injuring someone. To make sure the door does not slam shut, turn on the power sliding door feature.
Page 107: Resetting The Power Sliding Door
Resetting the Power Sliding Door The power sliding door may operate incorrectly or not at all because of the following conditions: • A low voltage or dead battery • A disconnected battery • If the instrument panel PWR/HEATED SEAT PSD fuse or the underhood fuse 8, 27, or 29 are removed or blown.
Page 108 Notice: If you open the liftgate without checking for overhead obstructions such as a garage door, you could break the liftgate glass. Always check to make sure the area above the liftgate is clear before opening it. CAUTION: It can be dangerous to drive with the liftgate open because carbon monoxide (CO) gas can come into your vehicle.
Page 109: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 110: Power Windows
Power Windows The switches on the driver’s door armrest control the front windows when the ignition is in RUN, ACCESSORY or when Retained Accessory Power (RAP) is active. See “Retained Accessory Power (RAP)” under Ignition Positions on page 2-31 . 2-24 The driver’s power window switch has two down positions.
Page 111: Visor Vanity Mirror
Power Rear Quarter Windows Your vehicle may have power rear quarter windows. This switch, located in the overhead console switchbank, is used for opening and closing the power rear quarter windows. Press the textured part of the switch to open the windows;...
Page 112: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have a theft-deterrent alarm system. 2-26 A light located on top of your instrument panel, near the center of the vehicle next to the windshield, will ﬂash...
Page 113: Disarming With Your Key
After all doors and the liftgate are closed and locked, the security light will begin ﬂashing at a very slow rate to let you know the system is armed. Arming with the Remote Keyless Entry Transmitter Your alarm system will arm when you use your remote keyless entry transmitter to lock the doors, if the key is not in the ignition.
Page 114 ® PASS-Key ® Your PASS-Key III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 115 If the engine does not start and the security message comes on, the key may have a damaged transponder. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the instrument panel PASS KEY fuse.
Page 116: Starting And Operating Your Vehicle
5. The security message will turn off once the key has been programmed. It may not be apparent that the security message went on due to how quickly the key is programmed. 6. Repeat Steps 1 through 4 if additional keys are to be programmed.
Page 117: Ignition Positions
Ignition Positions With the key in the ignition, you can turn it to ﬁve different positions. A (ACCESSORY): This is the position in which you can operate your electrical accessories. Press in the ignition switch as you turn the top of the key toward you. B (LOCK): This is the only position from which you can remove the key.
Page 118: Retained Accessory Power (Rap)
Retained Accessory Power (RAP) With RAP, the power windows, power rear quarter windows, audio system and the automatic level control will continue to work up to 10 minutes after the ignition key is turned to OFF and none of the doors are opened. Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N).
Page 119: Engine Coolant Heater
Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 120: Automatic Transaxle Operation
How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you’ll be parking your vehicle.
Page 121 CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
Page 122: Warm-Up Shift
AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you are: • Going less than 35 mph (55 km/h), push your accelerator pedal about halfway down. • Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
Page 123: Parking Brake
Notice: If your vehicle seems to start up rather slowly, or if it seems not to shift gears as you go faster, something may be wrong with a transaxle system sensor. If you drive very far that way, your vehicle can be damaged. So, if this happens, have your vehicle serviced right away.
Page 124: Shifting Into Park (P)
To release the parking brake, hold the regular brake pedal down with your right foot while you push down on the parking brake pedal with your left foot. To release the tension on the parking brake cable, you will need to apply about the same amount of pressure to the parking brake pedal as you did when you set the parking brake.
Page 125 2.1. Pull the lever toward you. 2.2. Move the lever up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P).
Page 126: Leaving Your Vehicle With The Engine Running
Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre.
Page 127: Shifting Out Of Park (P)
Shifting Out of Park (P) Your vehicle has an automatic transaxle shift lock control system which locks the shift lever in PARK (P) when the ignition is in the OFF position. In addition, you must fully apply your regular brakes before you can shift from PARK (P) when the ignition is in the RUN position.
Page 128: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • Your exhaust system sounds strange or different.
Page 129 CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. See the earlier Caution under Engine Exhaust on page 2-42 . Also, idling in a closed-in place can let deadly carbon monoxide (CO) into your vehicle even if the climate control fan is at the highest setting.
Page 130: Mirrors
Mirrors Manual Rearview Mirror To reduce glare from lights behind you, pull the lever toward you to the night position. To return the mirror to the day position, push the lever away from you. Outside Power Mirrors The control located on the driver’s door operates both outside rearview mirrors.
Page 131: Onstar System
Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right.
Page 132 ® OnStar Services One of the following plans is normally included for a speciﬁc duration with each vehicle equipped with ® OnStar . You can upgrade or extend your OnStar service plan to meet your needs. Safe and Sound Plan •...
Page 133: Homelink Transmitter
® HomeLink Transmitter HomeLink, a combined universal transmitter and receiver, provides a way to replace up to three hand held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional HomeLink information can be found on the internet at www.homelink.com or by calling 1 800 355 3515.
Page 134 Programming the HomeLink Transmitter ® Do not use the HomeLink Transmitter with any garage door opener that does not have the “stop and reverse” feature. This includes any garage door opener model manufactured before April 1, 1982. If you have a newer garage door opener with rolling codes, please be sure to follow steps 6 through 8 to complete the ®...
Page 135 Some entry gates and garage door openers may require you to substitute Step 3 with the procedure noted in “Gate Operator and Canadian Programming” later in this section. 4. The indicator light will ﬂash slowly at ﬁrst and then ® rapidly after HomeLink successfully receives the frequency signal from the hand-held transmitter.
Page 136: Gate Operator And Canadian Programming
Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for ® HomeLink to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to “time out”...
Page 137: Storage Areas
Reprogramming a Single HomeLink Button To program a device to HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink Do not release the button. 2. The indicator light will begin to ﬂash after 20 seconds. While still holding the HomeLink button, proceed with Step 2 under “Programming ®...
Page 138: Cupholder(S)
Cupholder(s) There are cupholders located below the center instrument panel switchbank. The cupholders have a removable liner for larger size cups and for cleaning the cupholders. To use the cupholders, simply pull out the tray. Keep the tray stowed in when not in use. Your vehicle also has cupholders on the bottom inboard side of the second row driver’s side captain’s chairs and the seatbacks have cupholders that can be...
Page 139: Overhead Console
Overhead Console If your vehicle is equipped with an overhead console, the console will contain the following: • Reading Lamps. See “Front Reading Lamps” and “Rear Reading Lamps” under Interior Lamps on page 3-18 . • Overhead Console Switchbank. See Overhead Console Switchbank on page 3-24 .
Page 140: Front Seat Storage Net
Front Seat Storage Net There may be a storage net that stretches between the front seats. Pull the hooks towards the passenger’s seat and insert them into the holes. To store the net, lift the hooks up and out of the holes. The net does not detach from the driver’s seat.
Page 141 If you have the luggage carrier, you can load things on top of your vehicle. Notice: Loading cargo on the luggage carrier that weighs more than 150 lbs. (68 kg) or hangs over the rear or sides of the vehicle may damage your vehicle.
Page 142: Rear Storage Area
Rear Storage Area Your vehicle has a storage compartment and may have a cupholder on the driver’s side of the vehicle, next to the third row seat(s). Convenience Net Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over.
Page 143 2. Attach the lower hooks to the metal rings on the ﬂoor. 3. Once you’ve loaded items into the net, stretch the higher side of the net up and over the top of the load to hold it ﬁrmly in place. The convenience net has a maximum capacity of 100 lbs.
Page 144: Convenience Center
Convenience Center CAUTION: If any removable convenience item is not secured properly, it can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to secure any such item properly. Your vehicle may have a convenience center. It comes with the stowable seat.
Page 145 4. Put the tray sill, located on the back of the convenience center, in the upright position. 5. Slide the convenience center in and align it so that the forks, located on the bottom rear of the convenience center, slide into the seat anchors. 6.
Page 146: Vehicle Personalization
Vehicle Personalization Your vehicle’s locks and lighting systems can be programmed with several different features. The features you can program depend on the options that came with your vehicle. The following chart shows the features that can be programmed. To determine which features your vehicle is equipped with, follow the steps listed for entering the programming mode.
Page 147: Entering Programming Mode
Entering Programming Mode To program features, your vehicle must be in the programming mode. Follow these steps: 1. The content theft-deterrent system must be disarmed. See Content Theft-Deterrent on page 2-26 . 2. Remove the BCM PRGRM fuse from the instrument panel fuse block, located to the right of the glove box.
Page 148: Automatic Door Locks
Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Follow the instructions for “Entering Programming Mode” earlier in this section. 2.
Page 149: Last Door Locking And Lockout Deterrent
Your vehicle was originally programmed to Mode 3. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Follow the instructions for Entering Programming Mode on page 2-61 . 2.
Page 150: Remote Driver Unlock Control
Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Follow the instructions for Entering Programming Mode on page 2-61 . 2.
Page 151: Remote Lock And Unlock Conﬁrmation
4. Press UNLOCK to change the current mode. 5. Press UNLOCK until you hear the number of chimes corresponding to the mode selection you want. The mode you selected is now set. You can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 152: Content Theft-Deterrent System
Your vehicle was originally programmed to Mode 4. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Follow the instructions for Entering Programming Mode on page 2-61 . 2.
Page 153: Arming And Disarming The Content
3. Count the number of chimes you hear. The number of chimes indicates the vehicle’s current programmed mode. If you do not wish to change the current mode, you can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 154 Mode 2: Remote Keyless Entry Transmitter Arm/Disarm Only • The system will arm when you lock the doors with your remote keyless entry transmitter. The key must be removed from the ignition when you lock the doors or the content theft-deterrent system will not arm.
Page 155: Exiting Programming Mode
3. Press the button with the horn symbol on the remote keyless entry transmitter. 4. Count the number of chimes you hear. The number of chimes indicates the vehicle’s current programmed mode. If you do not wish to change the current mode, you can either exit the programming mode by following the instructions later in this section or program the next feature available on your vehicle.
Page 156: Memory Seat
Memory Seat If your vehicle has this feature, the controls are located to the left of the steering column and are used to program and recall the driver’s seat settings. Adjust the driver’s seat to the position you would like for driving.
Page 157: Instrument Panel
Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-7 Horn ...3-7 Tilt Wheel ...3-7 Turn Signal/Multifunction Lever ...3-8 Exterior Lamps ...3-16 Interior Lamps ...3-18 Switchbanks ...3-23 Instrument Panel Switchbank ...3-23 Overhead Console Switchbank ...3-24 Ultrasonic Rear Parking Assist (URPA) ...3-24 Accessory Power Outlets ...3-27 Climate Controls ...3-28 Climate Control System ...3-28...
Page 158 Section 3 Driver Information Center (DIC) ...3-60 Audio System(s) ...3-63 Setting the Time ...3-63 Radio with Cassette and CD ...3-64 Radio with Six-Disc CD ...3-74 Entertainment System ...3-85 Rear Seat Audio (RSA) (Without Entertainment System) ...3-92 Rear Seat Audio (RSA) (With Entertainment System) ...3-94 Instrument Panel Theft-Deterrent Feature ...3-96...
Page 159 NOTES...
Page 160: Instrument Panel Overview
Instrument Panel Overview...
Page 161 A. Side Outlets. See Outlet Adjustment on page 3-34 . B. Front Outlets. See Outlet Adjustment on page 3-34 . C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-8 . D. Hazard Warning Flasher Switch. See Hazard Warning Flashers on page 3-6 . E.
Page 162: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. Your hazard warning ﬂashers button is located on top of the steering column.
Page 163: Other Warning Devices
Other Warning Devices If you carry reﬂective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn You can sound the horn by pressing the horn symbols on your steering wheel. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive.
Page 164: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals • Headlamp High/Low-Beam Changer • Flash-to-Pass • Windshield Wipers • Windshield Washer • Cruise Control Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions.
Page 165 If a bulb is burned out, replace it to help avoid an accident. If the arrows do not go on at all when you signal a turn, check for burned-out bulbs and check the fuse. See Bulb Replacement on page 5-50 and Fuses and Circuit Breakers on page 5-101 .
Page 166: Windshield Wipers
Windshield Wipers WIPER: Turn this band to operate the windshield wipers. MIST: Turn the band to MIST for a single wiping cycle. Hold it there until the wipers start. Then let go. The wipers will stop after one wipe. If you want more wipes, hold the band on mist longer.
Page 167 CAUTION: In freezing weather, do not use your washer until the windshield is warmed. Otherwise the washer ﬂuid can form ice on the windshield, blocking your vision. Rear Window Washer/Wiper If your vehicle has a rear window wiper, the switch is located in the instrument panel switchbank.
Page 168: Cruise Control
Cruise Control Your vehicle may have cruise control. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).
Page 169 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 170 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, shuts off the cruise control. But you do not need to reset it. Once you are going about 25 mph (40 km/h) or more, you can move the cruise control switch from ON to resume/accelerate (R/A) brieﬂy.
Page 171 Passing Another Vehicle While Using Cruise Control To pass another vehicle while using cruise control, use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the...
Page 172: Exterior Lamps
Exterior Lamps The control to the left of the steering column operates the exterior lamps. 3-16 (Off/Auto): Turning the control to this setting will activate the automatic headlamp control when it is dark enough outside and turn off all of the lamps and lights during the day, except the Daytime Running Lamps (DRL).
Page 173 Daytime Running Lamps/Automatic Headlamp System Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset.
Page 174: Fog Lamps
Fog Lamps Your vehicle may have fog lamps. If it does, the fog lamps switch is located in the instrument panel switchbank. Press the fog lamp symbol on the switch to turn on the lamps. The indicator light will be lit while the fog lamps are on. Press the top part of the switch to turn them off.
Page 175: Interior Lamps Override
Interior Lamps Override This switch is located in the overhead console switchbank. Press the bottom of the switch to keep the interior lamps off while any door is open, or the top of the switch to allow the interior lamps to come on while any door is open.
Page 176: Delayed Lighting
Delayed Lighting The delayed lighting feature will continue to illuminate the interior for 25 seconds after all doors have been closed, so that you can ﬁnd your ignition and buckle your safety belt at night. Delayed lighting will not occur while the ignition is in RUN or ACCESSORY.
Page 177 Front Reading Lamps There are two reading lamps in the overhead console. To turn either reading lamp on or off, press the lens of the lamp. These lamps will come on each time you open a door, unless you turn on the interior lamps override feature.
Page 178: Rear Reading Lamps
Rear Reading Lamps There may be two reading lamps in the third row headliner. To turn either reading lamp on or off, press the lens of the lamp. There is also a reading lamp in the second row, integrated with the dome lamp. To turn the second row reading lamp on or off, press the button next to the lamp lens.
Page 179: Switchbanks
Switchbanks There are two sets of switchbanks located in the front of the vehicle. The switches will vary with the options that are on your vehicle. Instrument Panel Switchbank The instrument panel switchbank is located in the instrument panel below the comfort controls. This switchbank may contain the following: •...
Page 180: Overhead Console Switchbank
Overhead Console Switchbank The overhead console switchbank is located in the overhead console. This switchbank may include the following: • Interior Lamps Override. See “Interior Lamps Override” under Interior Lamps on page 3-18 . • Power Sliding Door(s)/Override Switch(es). See Power Sliding Door (PSD) on page 2-17 . •...
Page 181: How The System Works
CAUTION: Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while parking. And, the system does not detect objects that are more than 5 feet (1.5 meters) behind the vehicle.
Page 182 If an object is detected at a REVERSE (R) speed of less than 3 mph (5 km/h), one of the following will occur: Description English amber light amber/amber lights 40 in. amber/amber/red lights 20 in. & continuous chime amber/amber/red lights ﬂashing & continuous chime A chime will sound the ﬁrst time an object is detected between 20 inches (0.5 m) and 5 feet (1.5 m) away.
Page 183: Accessory Power Outlets
Accessory Power Outlets With accessory power outlets you can plug in electrical equipment such as a cellular telephone or CB radio. The front accessory power outlet is located below the cupholder drawer. Pull the cover down to use the accessory power outlet. When not in use, keep the cover on.
Page 184: Climate Controls
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 185: Defogging And Defrosting
(Recirculation): This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off. When the button is pressed, an indicator light will come on.
Page 186: Rear Window Defogger
Turn the right knob to select the defog or defrost mode. (Defog): This mode directs air to the windshield and the ﬂoor outlets. When you select this mode, the system turns off recirculation and runs the air-conditioning compressor unless the outside temperature is at or below freezing.
Page 187: Dual Climate Control System
Dual Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside of your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 188 (Recirculation): This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off. When the button is pressed, an indicator light will come on.
Page 189 Defogging and Defrosting Fog on the inside of windows is a result of high humidity, or moisture, condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield.
Page 190: Outlet Adjustment
Outlet Adjustment Use the knob located in the center of the outlet, to change the direction of the air ﬂow. Operation Tips • Clear away any ice, snow or leaves from the air inlets on the hood that may block the ﬂow of air into your vehicle.
Page 191: Selecting The Fan Speed
These controls are overhead, on the control panel located behind the driver’s seat. A rear-seat passenger can use these controls to personally adjust the temperature and the fan speed for the rear-seating area. The fan knob located on the switchbank must be turned to R (Rear) to allow the rear-seat passengers to use the controls located on the control panel in the rear-seating area.
Page 192: Rear Climate Control System
Setting the Temperature If the driver is adjusting the temperature, do the following: To increase or decrease the temperature for the entire vehicle, use the temperature controls located on the main climate-control panel. If using the main climate-control panel, then the air-conditioning system must be on to direct cooled air to the rear of the vehicle.
Page 193 This knob is located below the main climate-control system on the instrument panel switchbank. Use this knob to adjust the fan speed for the rear-seat passengers, from the front-seating area. These controls are overhead, on the control panel located behind the front seats. A rear-seat passenger can use these controls to personally adjust the temperature and the fan speed for the rear-seating area.
Page 194 Selecting the Fan Speed If the driver is adjusting the fan speed, use the following control: (Fan): Turn the fan knob on the rear fan control located below the main climate-control system on the switchbank to numeral 1, 2, or 3 to increase or decrease airﬂow to the rear-seating area.
Page 195: Passenger Compartment Air Filter
For more information on how to use the main climate control system, see “Climate Control System” listed previously in this section. For information on ventilation, see “Outlet Adjustment” under “Climate Control System” listed previously in this section. Passenger Compartment Air Filter Passenger compartment air, both outside and recirculated air, is routed through a passenger compartment ﬁlter.
Page 196 2. Then push the tab, located on the left of the inner access panel, to the right. 3-40 3. The ﬁrst air ﬁlter will pull straight out. To remove the second, reach in and slide it toward the opening. Pull the second ﬁlter out. 4.
Page 197: Warning Lights, Gages And Indicators
Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 198: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Page 199: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). Your vehicle has a tamper-resistant odometer.
Page 200: Retro-Active Reset
Retro-Active Reset Each of the two trip odometers has a feature called retro-active reset. This feature can be used to set either or both trip odometer(s) to the number of miles (kilometers) driven since the ignition was last turned on. This can be used if you forget to reset your trip odometer at the beginning of a trip.
Page 201: Air Bag Readiness Light
Air Bag Readiness Light There is an air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the air bag sensor, the air bag modules, the wiring and the diagnostic module.
Page 202: Brake System Warning Light
Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If it stays on after your parking brake is fully released, it means you have a brake problem.
Page 203: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light Your vehicle may have this light. If it does, the anti-lock brake system warning light should come on for a few seconds when you turn the ignition key to RUN. If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off.
Page 204: Engine Coolant Temperature Gage
• If there’s a brake system problem that is speciﬁcally related to traction control, the traction control system will turn off and the warning light will come on. If your brakes begin to overheat, the traction control system will turn off and the warning light will come on until your brakes cool down.
Page 205: Malfunction Indicator Lamp
Malfunction Indicator Lamp Service Engine Soon Light in the United States or Check Engine Light in Canada United States Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 206: If The Light Is On Steady
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: •...
Page 207 Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-4 . Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration or stumbling on acceleration.
Page 208: Fuel Gage
Fuel Gage United States When the indicator nears empty, you still have a little fuel left, but you should get more soon. If your fuel is low, the warning message in the message center will come on. See Low Fuel Warning Message on page 3-59 .
Page 209: Message Center
Message Center The message center is located in the instrument panel cluster. It gives you important safety and maintenance facts. Service Traction System Warning Message United States If your vehicle has the traction control system and this message is displayed when you’re driving, there may be a problem with your traction control system.
Page 210: Traction Active Message
Traction Active Message United States If your vehicle has the traction control system, the TRACTION ACTIVE message will appear when the traction control system is limiting wheel spin. You may feel or hear the system working, but this is normal. Slippery road conditions may exist if this message appears, so adjust your driving accordingly.
Page 211: Charging System Indicator Message
Charging System Indicator Message The charging system battery symbol will come on in the message center when you turn on the ignition as a check to show you it is working. It will remain on as long as the engine is not running. It should go out once the engine is running.
Page 212: Maintenance Schedule
When the engine is running and this message appears, the engine oil level may be too low. There may also be another problem causing low oil pressure. CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre.
Page 213: Power Sliding Door Warning Message
Power Sliding Door Warning Message United States This message will come on if the power sliding door is not completely closed and the ignition is turned to RUN or START. If you shift the transaxle out of PARK (P) while the power sliding door is open or in the process of closing, and the power sliding door is turned off, a buzzer will sound.
Page 214: Rear Hatch Ajar Warning Message
Rear Hatch Ajar Warning Message United States This message will come on when the ignition is turned to RUN or START and the rear hatch is open. 3-58 PASS-Key Canada United States If you are ever driving and this message comes on and stays on, you will be able to restart your engine if you turn it off.
Page 215: All-Wheel Drive Disable Warning Message
All-Wheel Drive Disable Warning Message United States Your vehicle may have this message. If it does, it will come on when there is a spare tire on the vehicle, or when the anti-lock brake system warning light comes on, or when the rear differential ﬂuid is overheating. This message will go out when the differential ﬂuid cools.
Page 216: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle may have a DIC. If it does, the DIC will show information about the vehicle and the surroundings. E/M (English/Metric Button): You can change the display to a metric or English reading at any time by pressing E/M.
Page 217 Setting the Variance Turn the ignition on and cycle the DIC to the compass/ temperature mode. Press both the E/M and MODE buttons simultaneously for about ﬁve seconds. The last entered variance zone number will be displayed. Press the E/M button until the proper variance number, as shown on the map, is showing.
Page 218: Error Displays
Error Displays • An error of the vehicle’s speed sensor or fuel sender will cause -E- to be displayed. • In the absence of vehicle communications, a dash “- -” is displayed. If one of these error messages appear, see your dealer. Trip Computer There are ﬁve trip computer displays available by pushing the MODE button.
Page 219: Audio System(S)
Audio System(s) Notice: Before you add any sound equipment to your vehicle – like a tape player, CB radio, mobile telephone or two-way radio – be sure you can add what you want. If you can, it’s very important to do it properly.
Page 220: Radio With Cassette And Cd
Radio with Cassette and CD Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease volume. AUTO VOL (Automatic Volume): With automatic volume, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 221: Finding A Station
Finding a Station BAND: Press this button to switch between FM1, FM2, or AM. The display will show your selection. TUNE: Turn this knob to select radio stations. SEEK : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 222 Setting the Tone (Bass/Treble) AUDIO: Push and release the AUDIO knob until BASS or TREB appears on the display. Turn the knob to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, you may want to decrease the treble.
Page 223 Radio Data System (RDS) Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, your radio can do the following: • Seek to stations broadcasting the selected type of programming •...
Page 224: Rds Messages
BAND (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the same program type. To turn alternate frequency on, press and hold BAND for two seconds. AF ON will appear on the display. The radio may switch to stronger stations. To turn alternate frequency off, press and hold BAND again for two seconds.
Page 225: Playing A Cassette Tape
If TRAF is on the display you can press the TRAF button to turn of the traffic announcements. Your radio will play the traffic announcement if the volume is low. Your radio will interrupt the play of a CD if the last tuned station broadcasts traffic announcements.
Page 226 SEEK and a negative number will appear on the display while the cassette player is in the previous mode. Pressing this pushbutton multiple times or holding it will increase the number of selections to be searched back, up to -9. 2 NEXT: Your tape must have at least three seconds of silence between each selection for next to work.
Page 227: Cassette Tape Messages
Cassette Tape Messages CHK TAPE (Check Tape): If this message appears on the display, the tape will not play because of one of the following errors: • The tape is tight and the player cannot turn the tape hubs. Remove the tape. Hold the tape with the open end down and try to turn the right hub counterclockwise with a pencil.
Page 228 If you turn off the ignition or radio with a CD in the player it will stay in the player. When you turn on the ignition or radio, the CD will start to play where it stopped, if it was the last selected audio source. As each new track starts to play, the track number will appear on the display.
Page 229 SEEK : The right arrow is the same as the NEXT pushbutton, and the left arrow is the same as the PREV pushbutton. If you hold either arrow or press it more than once, the player will continue moving backward or forward through the CD. DISPL (Display): Press this knob to see how long the current track has been playing.
Page 230: Radio With Six-Disc Cd
Radio with Six-Disc CD Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOLUME: Turn this knob to increase or to decrease volume. 3-74 AUTO VOL (Automatic Volume): Your system has a feature called automatic volume. With this feature, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 231 Finding a Station BAND: Press this button to switch between FM1, FM2, or AM. The display will show your selection. TUNE: Turn this knob to select radio stations. SEEK : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 232 Setting the Tone (Bass/Treble) AUDIO: Push the AUDIO knob until BASS, MID, or TREB appears on the display. Turn the knob to increase or to decrease. If a station is weak or noisy, you may want to decrease the treble. To adjust bass, midrange, or treble to the middle position, select BASS, MID, or TREB and push and hold the AUDIO knob.
Page 233 Radio Data System (RDS) Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, your radio can do the following: • Seek to stations broadcasting the selected type of programming •...
Page 234: Setting Preset Ptys (Rds Only)
To use the PTY interrupt feature, press and hold the P-TYPE button until you hear a beep on the PTY you want to interrupt with. When selected, an asterisk will appear beside that PTY on the display. You may select multiple interrupts if desired.
Page 235 RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is muted or a CD is playing. If a CD is playing, play will stop during the announcement.
Page 236: Radio Messages
Radio Messages CAL ERR (Calibration Error): Your audio system has been calibrated for your vehicle from the factory. If CAL ERR appears on the display it means that your radio has not been conﬁgured properly for your vehicle and it must be returned to the dealer for service. LOCKED: This message is displayed when the ®...
Page 237: Playing A Speciﬁc Loaded Cd
The CD will begin to play automatically. As each new track starts to play, the track number will appear on the display. To insert multiple CDs, do the following: 1. Turn the ignition on. 2. Press and hold the LOAD side of the LOAD CD button for two seconds.
Page 238 REMOVE CD will be displayed. You can now remove the CD. If the CD is not removed, after 25 seconds, the CD will be automatically pulled back into the receiver. If you try to push the CD back into the receiver, before the 25 second time period is complete, the receiver will sense an error and will try to eject the CD several times before stopping.
Page 239: Using Song List Mode
SEEK : Press the left arrow to go to the start of the current track, if more than ten seconds have passed. Press the right arrow to go to the next track. If you hold an arrow or press it more than once, the player will continue moving backward or forward through the CD.
Page 240 4. Press and hold the SONG LIST button to save the track into memory. When SONG LIST is pressed a beep will be heard immediately. After two seconds of continuously pressing SONG LIST, two beeps will sound to conﬁrm that the track has been saved. 5.
Page 241: Entertainment System
CD Messages CHECK CD: If this message appears on the radio display, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 242 Headphones The entertainment system includes dual channel, wireless headphones. The headphones have an ON/OFF switch, a channel A/B switch and a volume control. To use the headphones, turn the switch located on the left side to ON. An indicator light located on the right side will illuminate.
Page 243: Audio Speakers
Battery Replacement To change the batteries, do the following: 1. Slide open the battery door located on the left side of the headphones. 2. Replace the two AAA batteries in the compartment. Make sure that they are installed correctly. 3. Slide the battery door shut. If the headphones are to be stored for a long period of time, remove the batteries and keep them in a cool, dry place.
Page 244: Video Screen
Video Screen The video screen is located in the overhead console. 3-88 To use the video screen, do the following: 1. Push forward on the release button and the screen will fold down. 2. Pull the screen toward you and adjust its position as desired.
Page 245: Dvd Player
DVD Player The DVD player is located in the front ﬂoor console. The DVD player can be controlled by the buttons on the DVD player and by the buttons on the remote control. See “Remote Control” later in this section for more information.
Page 246: Remote Control
Some DVDs will not allow you to fast forward or skip the copyright information or previews. Some DVDs will begin playing the movie automatically after the previews have ﬁnished (although there may be a delay of up to 30 seconds). If the DVD does not begin playing the movie automatically, press the play/pause button on the face of the DVD player or the remote control.
Page 247: Remote Control Buttons
Remote Control Buttons Volume : Press the up or the down arrow to increase or to decrease volume. (Play/Pause): Press this button to play a disc. Press this button while a disc is playing to pause. Press it again to continue playing. If you press and hold this button for three seconds or more, the DVD player will turn off.
Page 248: Rear Seat Audio (Rsa) (Without Entertainment System)
Battery Replacement To change the batteries, do the following: 1. Remove the screw and open the battery door located on the back of the remote control. 2. Replace the two AAA batteries in the compartment. Make sure that they are installed correctly. 3.
Page 249: Rear Seat Radio Controls
Rear Seat Radio Controls The following functions are controlled by the RSA system buttons: PWR (Power): Press this button to turn RSA on or off. VOL (Volume): Press this knob lightly so it extends. Turn the knob to increase or to decrease volume. Push the knob back into its stored position when you are not using it.
Page 250: (With Entertainment System)
P.SET PROG (Preset Program): The front passengers must be listening to something different for each of these functions to work: • Press this button to scan through the preset radio stations set on the pushbuttons on the main radio. The radio will go to a preset station stored on your pushbuttons, play for a few seconds, then go on to the next preset station.
Page 251 Rear Seat Radio Controls The following functions are controlled by the RSA system buttons: RSA PWR (Power): Press this button to turn RSA on or off. The headphone symbol will appear on the display above the video screen when the system is on. BAND: Press this button to switch between FM1, FM2, or AM when the headphones are on channel B.
Page 252: Theft-Deterrent Feature
P.SET SCAN (Preset Scan): The front passengers must be listening to something different for each of these functions to work: • Press and hold this button to scan through the preset radio stations set on the pushbuttons on the main radio. The radio will go to a preset station stored on your pushbuttons, play for a few seconds, then go on to the next preset station.
Page 253: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, you can control certain radio functions using the buttons on your steering wheel. SEEK : Press the up or the down arrow to go to the next or to the previous station. When playing a cassette tape or CD, press the up arrow to hear the next selection.
Page 254: Dvd Distortion
DVD Distortion You may experience video distortion when operating cellular phones, scanners, CB radios, Global Position Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It may be necessary to turn off the DVD player when operating one of these devices in or near the vehicle. ®...
Page 255: Care Of Your Cds And Dvds
The broken tape detection feature of your cassette tape player may identify the cleaning cassette as a damaged tape, in error. To prevent the cleaning cassette from being ejected, use the following steps: 1. Turn the ignition on. 2. Turn the radio off. 3.
Page 256: Care Of Your Cd And Dvd Player
Care of Your CD and DVD Player The use of CD lens cleaner discs is not advised, due to the risk of contaminating the lens of the CD optics with lubricants internal to the CD mechanism. Cleaning Your DVD Player When cleaning the outside DVD cabinet face and buttons, use only a clean cloth dampened with clean water.
Page 257 Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-2 Control of a Vehicle ...4-5 Braking ...4-6 Traction Control System (TCS) ...4-8 All-Wheel Drive (AWD) System ...4-10 Steering ...4-10 Off-Road Recovery ...4-12 Passing ...4-13 Loss of Control ...4-14 Driving at Night ...4-15 Driving in Rain and on Wet Roads ...4-17...
Page 258: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-22 . Defensive driving really means “be ready for anything.”...
Page 259 Many adults — by some estimates, nearly half the adult population — choose never to drink alcohol, so they never drive after drinking. For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological and developmental reasons for these laws.
Page 260 There is a gender difference, too. Women generally have a lower relative percentage of body water than men. Since alcohol is carried in body water, this means that a woman generally will reach a higher BAC level than a man of her same body weight will when each has the same number of drinks.
Page 261: Control Of A Vehicle
There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord or heart. This means that when anyone who has been drinking —...
Page 262: Braking
Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about 3/4 of a second. But that is only an average.
Page 263 When you start your engine, or when you begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on, and you may even notice that your brake pedal moves or pulses a little.
Page 264: Traction Control System (Tcs)
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 265 If your vehicle is in cruise control when the traction control system begins to limit wheel spin, the cruise control will automatically disengage. When road conditions allow you to safely use it again, you may reengage the cruise control. See “Cruise Control” under Turn Signal/Multifunction Lever on page 3-8 .
Page 266: Power Steering
All-Wheel Drive (AWD) System If your vehicle has all-wheel drive (AWD), the AWD system operates automatically without any action required by the driver. If the front drive wheels begin to slip, the rear wheels will automatically begin to drive the vehicle as required. There may be a slight engagement noise during hard use but this is normal.
Page 267: Steering In Emergencies
The same thing can happen if you are steering through a sharp curve and you suddenly accelerate. Those two control systems — steering and acceleration — can overwhelm those places where the tires meet the road and make you lose control. See Traction Control System (TCS) on page 4-8 .
Page 268: Off-Road Recovery
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Page 269: Passing
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traffic for several seconds.
Page 270: Loss Of Control
• Check your mirrors, glance over your shoulder, and start your left lane change signal before moving out of the right lane to pass. When you are far enough ahead of the passed vehicle to see its front in your inside mirror, activate your right lane change signal and move back into the right lane.
Page 271: Driving At Night
Of course, traction is reduced when water, snow, ice, gravel or other material is on the road. For safety, you will want to slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
Page 272 Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you can not see as well, you may need to slow down and keep more space between you and other vehicles.
Page 273: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can not stop, accelerate or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 274 Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can not, try to slow down before you hit them. 4-18 CAUTION: Wet brakes can cause accidents.
Page 275: Driving Through Deep Standing Water
Hydroplaning usually happens at higher speeds. There just is not a hard and fast rule about hydroplaning. The best advice is to slow down when it is raining. Driving Through Deep Standing Water Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine.
Page 276: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. 4-20 Here are ways to increase your safety in city driving: •...
Page 277: Freeway Driving
Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or superhighways) are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 278: Before Leaving On A Long Trip
Before changing lanes, check your mirrors. Then use your turn signal. Just before you leave the lane, glance quickly over your shoulder to make sure there is not another vehicle in your “blind” spot. Once you are moving on the freeway, make certain you allow a reasonable following distance.
Page 279: Highway Hypnosis
• Fuel, Engine Oil, Other Fluids: Have you checked all levels? • Lamps: Are they all working? Are the lenses clean? • Tires: They are vitally important to a safe, trouble-free trip. Is the tread good enough for long-distance driving? Are the tires all inﬂated to the recommended pressure? •...
Page 280: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in ﬂat or rolling terrain. 4-24 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable.
Page 281 CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Page 282: Winter Driving
Winter Driving 4-26 Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth and a couple of reﬂective warning triangles.
Page 283: Driving On Snow Or Ice
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You will have a lot less traction or “grip”...
Page 284: If You Are Caught In A Blizzard
Unless you have the anti-lock braking system, you will want to brake very gently, too. (If you do have anti-lock, see Braking on page 4-6 . This system improves your vehicle’s stability when you make a hard stop on a slippery road.) Whether you have the anti-lock braking system or not, you will want to begin stopping sooner than you would on dry pavement.
Page 285 • Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, ﬂoor mats — anything you can wrap around yourself or tuck under your clothing to keep warm. You can run the engine to keep warm, but be careful.
Page 286: If You Are Stuck: In Sand, Mud
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 287: Towing
By slowly spinning your wheels in the forward and reverse directions, you will cause a rocking motion that may free your vehicle. If that does not get you out after a few tries, you may need to be towed out. If you do need to be towed out, see Towing Your Vehicle on page 4-31 .
Page 288: Dinghy Towing
Dinghy Towing Your vehicle was not designed to be towed with all of its wheels on the ground. If you have a two-wheel-drive vehicle, it can be towed with two of its wheels on the ground. See “Dolly Towing” following. If you have an all-wheel-drive vehicle, it cannot be towed with any of its wheels on the ground.
Page 289: Loading Your Vehicle
Loading Your Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 290 The Tire and Loading Information label also tells you the size and recommended inﬂation pressure for the original equipment tires on your vehicle. For more information on tires and inﬂation, see Tires on page 5-58 and Inﬂation - Tire Pressure on page 5-67 . If your vehicle does not have the Tire and Loading Information label, the Certiﬁcation/Tire label shows the tire size and recommended inﬂation pressures...
Page 291 Example 1 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 1 Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs. (317 kg) Example 2 Loading Your Vehicle Description Vehicle Capacity Weight...
Page 292 Example 3 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight 4-36 Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 293 The label shows the size of your original tires and the inﬂation pressures needed to obtain the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR).
Page 294: Towing A Trailer
Automatic Level Control On vehicles equipped with automatic level control, the rear of the vehicle is automatically kept level as you load or unload your vehicle. However, you should still not exceed the GVWR or the GAWR. See Loading Your Vehicle on page 4-33 . You may hear the compressor operating when you load or unload your vehicle, and periodically as the system self-adjusts.
Page 295: If You Do Decide To Pull A Trailer
Your vehicle can tow a trailer. To identify what the vehicle trailering capacity is for your vehicle, you should read the information in “Weight of the Trailer” that appears later in this section. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, acceleration, braking, durability, and fuel economy.
Page 296: Weight Of The Trailer
4-40 You can ask your dealer for our trailering information or advice, or you can write us at: Oldsmobile Customer Assistance P.O. Box 33171 Detroit, MI 48232-5171 In Canada, write to:...
Page 297: Total Weight On Your Vehicle's Tires
If you are using a weight-carrying or a weight-distributing hitch, the trailer tongue weight (A) should be 10 percent to 15 percent of the total loaded trailer weight (B). Do not exceed the maximum allowable tongue weight for your vehicle. After you have loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper.
Page 298: Safety Chains
Hitches It is important to have the correct hitch equipment. Crosswinds, large trucks going by and rough roads are a few reasons why you will need the right hitch. Here are some rules to follow: • The bumpers on your vehicle are not intended for hitches.
Page 299: Driving With A Trailer
Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You can not see or smell CO. It can cause unconsciousness or death. See Engine Exhaust on page 2-42 .
Page 300: Following Distance
Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You will need more passing distance up ahead when you are towing a trailer.
Page 301: Driving On Grades
Driving On Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you do not shift down, you might have to use your brakes so much that they would get hot and no longer work well. If you are towing a trailer that weighs more than 1,000 lbs.
Page 302: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • Start your engine. • Shift into a gear. • Release the parking brake. 2. Let up on the brake pedal. 3.
Page 303 Section 5 Service ...5-3 Doing Your Own Service Work ...5-3 Adding Equipment to the Outside of Your Vehicle ...5-4 Fuel ...5-4 Gasoline Octane ...5-4 Gasoline Speciﬁcations ...5-5 California Fuel ...5-5 Additives ...5-6 Fuels in Foreign Countries ...5-6 Filling Your Tank ...5-7 Filling a Portable Fuel Container ...5-9 Checking Things Under the Hood ...5-10 Hood Release ...5-10...
Page 304 Section 5 Appearance Care ...5-92 Cleaning the Inside of Your Vehicle ...5-92 Care of Safety Belts ...5-95 Weatherstrips ...5-95 Cleaning the Outside of Your Vehicle ...5-95 Sheet Metal Damage ...5-98 Finish Damage ...5-98 Underbody Maintenance ...5-98 Chemical Paint Spotting ...5-98 Vehicle Care/Appearance Materials ...5-99 Service and Appearance Care Vehicle Identiﬁcation ...5-100...
Page 305: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 306: Adding Equipment To The Outside
CAUTION: (Continued) • Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt. Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it.
Page 307: Gasoline Speciﬁcations
Gasoline Speciﬁcations It is recommended that gasoline meet speciﬁcations which were developed by automobile manufacturers around the world and contained in the World-Wide Fuel Charter which is available from the Alliance of Automobile Manufacturers at www.autoalliance.org. Gasoline meeting these speciﬁcations could provide improved driveability and emission control system performance compared to other gasoline.
Page 308: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. You should not have to add anything to your fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S.
Page 309: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 310 While refueling, let the fuel cap hang by the tether as shown. CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather.
Page 311: Filling A Portable Fuel Container
CAUTION: If a ﬁre starts while you are refueling, do not remove the nozzle. Shut off the ﬂow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately. The malfunction indicator lamp (SERVICE ENGINE SOON or CHECK ENGINE light) will come on if the fuel cap is not properly installed.
Page 312: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. CAUTION: Things that burn can get on hot engine parts and start a ﬁre.
Page 313 3. Lift the hood. 4. Pull forward on the hood prop to release it from its storage clip. The hood prop may be hot due to increased engine temperatures under the hood, so be careful when handling it. Use your hood prop sleeve when handling the hood prop.
Page 314: Engine Compartment Overview
Engine Compartment Overview When you lift the hood, you’ll see these items: 5-12...
Page 315: Engine Oil
A. Underhood Fuse Block. See Fuses and Circuit Breakers on page 5-101 . B. Remote Positive (+) Terminal. See Jump Starting on page 5-42 . C. Windshield Washer Fluid Reservoir. See Windshield Washer Fluid on page 5-37 . D. Radiator Pressure Cap. See Radiator Pressure Cap on page 5-25 .
Page 316: When To Add Engine Oil
When to Add Engine Oil If the oil is at or below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 317 • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, if it is going to be 0°F (–18°C) or above and SAE 5W-30 is not available, you may use SAE 10W-30. These numbers on an oil container show its viscosity, or thickness.
Page 318: When To Change Engine Oil
Notice: Use only engine oil identiﬁed as meeting GM Standard GM6094M and showing the American Petroleum Institute Certiﬁed For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty. ® GM Goodwrench oil meets all the requirements for your vehicle.
Page 319: What To Do With Used Oil
How to Reset the Change Engine Oil Message The GM Oil Life System calculates when to change your engine oil and ﬁlter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE ENGINE OIL message being turned on, reset the system.
Page 320: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at every oil change and replace it at the ﬁrst oil change after 25,000 miles (40 000 km).
Page 321: Automatic Transaxle Fluid
6. Latch the hooks to secure the panel in place. If the panel moves easily, check that the tabs are seated correctly in the slots. 7. Put the duct back on and reinstall the clamps. CAUTION: Operating the engine with the air cleaner/ﬁlter off can cause you or others to be burned.
Page 322: How To Check Automatic Transaxle Fluid
How to Check Automatic Transaxle Fluid Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little ﬂuid can damage the transaxle.
Page 323 Then, without shutting off the engine, follow these steps: The dipstick is located toward the back of the engine compartment, next to the brake master cylinder reservoir. The dipstick has a bright, red loop design for easy identiﬁcation. See Engine Compartment Overview on page 5-12 for more information on location.
Page 324: Engine Coolant
How to Add Fluid Automatic Transaxle Fluid Refer to the Maintenance Schedule to determine what kind of transaxle ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12 . If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level into the cross-hatched area on the dipstick.
Page 325: What Engine Coolant To Use
What Engine Coolant to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which will not damage aluminum parts. If you use this coolant mixture, you do not need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 326: Checking Coolant
Checking Coolant The coolant recovery tank is located on the driver’s side of the vehicle, above the engine air cleaner/ﬁlter. See Engine Compartment Overview on page 5-12 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the FULL COLD mark, or a little higher.
Page 327: Radiator Pressure Cap
CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Occasionally check the coolant level in the radiator. For information on how to add coolant to the radiator, see Cooling System on page 5-28 .
Page 328: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming CAUTION: (Continued) 5-26 CAUTION: (Continued) from it.
Page 329: If No Steam Is Coming From Your Engine
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: • Climb a long hill on a hot day •...
Page 330: Cooling System
Cooling System When you decide it is safe to lift the hood, here is what you will see: A. Radiator Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank 5-28 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
Page 331 CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned.
Page 332 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at or above the FULL COLD mark, add a 50/50 mixture of clean, drinkable water and ® DEX-COOL engine coolant at the coolant recovery tank.
Page 333: How To Add Coolant To The Radiator
When the coolant in the coolant recovery tank is at or above the FULL COLD mark, start your vehicle. If the overheat warning continues, there’s one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it.
Page 334 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise until it ﬁrst stops. Do not press down while turning the pressure cap.
Page 335 Housing 3. After the engine cools, open the coolant air bleed valves. There are two bleed valves. One is located on the thermostat housing. The other is located on the thermostat bypass tube. Bypass Tube 4. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the ﬁller neck.
Page 336 5-34 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. 7. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL through the ﬁller neck until the level reaches the base of the ﬁller neck.
Page 337 8. Then replace the pressure cap. At any time during 9. Then ﬁll the coolant recovery tank to the this procedure if coolant begins to ﬂow out of the ﬁller FULL COLD mark. neck, reinstall the pressure cap. Be sure the arrows 10.
Page 338: Power Steering Fluid
Power Steering Fluid When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem.
Page 339: Windshield Washer Fluid
Windshield Washer Fluid What Washer Fluid to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 340: Brakes
Brakes Brake Fluid Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal 5-38 brake lining wear.
Page 341: What To Add
When your brake ﬂuid falls to a low level, your brake warning light will come on. See Brake System Warning Light on page 3-46 . What to Add When you do need brake ﬂuid, use only DOT-3 brake ﬂuid. Use new brake ﬂuid from a sealed container only. See Recommended Fluids and Lubricants on page 6-12 .
Page 342: Brake Wear
Brake Wear Your vehicle has front disc brakes and may have rear drum brakes or rear disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal ﬁrmly).
Page 343: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system —...
Page 344: Jump Starting
Vehicle Storage If you are not going to drive your vehicle for 25 days or more, remove the black, negative ( ) cable from the battery. This will help keep your battery from running down. CAUTION: Batteries have acid that can burn you and gas that can explode.
Page 345 Notice: Ignoring these steps could result in costly damage to your vehicle that would not be covered by your warranty. Trying to start your vehicle by pushing or pulling it will not work, and it could damage your vehicle. 1. Check the other vehicle. It must have a 12-volt battery with a negative ground system.
Page 346 The terminal is located under a tethered cap at the front of the underhood fuse block. See Engine Compartment Overview on page 5-12 for more information on location. Squeeze the tabs and pull up on the cap to access the remote positive (+) terminal. You should always use the remote positive (+) terminal instead of the positive (+) terminal on your battery.
Page 347 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 348 8. Now connect the black negative ( ) cable to the negative ( ) terminal of the good battery. Use a remote negative ( ) terminal if the vehicle has one. Do not let the other end touch anything until the next step.
Page 349 Notice: If the jumper cables are removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 350: All-Wheel Drive
All-Wheel Drive If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. However, they have two additional systems that need lubrication. Transfer Case (Power Transfer Unit) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
Page 351: Carrier Assembly-Differential
Carrier Assembly-Differential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Scheduled Maintenance on page 6-4 . How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 352: Bulb Replacement
Bulb Replacement For the type of bulbs, see Replacement Bulbs on page 5-56 . For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 353 7. Install the new bulb through the black retainer ring and into the electrical connector. Tighten the black retainer ring in place. Push the bulb ﬁrmly enough so that the blue tabs hook over the tab on the bulb. 8. Carefully put the bulb assembly back into the lamp housing.
Page 354: Front Turn Signal, Sidemarker And Parking Lamps
9. Align the pins on the bottom of the headlamp assembly with the holes in the lamp support bracket. 10. To reinstall the front turn signal/parking lamp assembly. See Front Turn Signal, Sidemarker and Parking Lamps on page 5-52 next. 5-52 Front Turn Signal, Sidemarker and Parking Lamps...
Page 355 Front Turn Signal/Parking Lamp Front Sidemarker Lamp 4. Unscrew the bulb socket from the lamp assembly by pressing the tab while turning it counterclockwise. 5. Replace the bulb by pulling the old one out and gently pushing the new one into the lamp socket. 6.
Page 356: Taillamps, Turn Signal, Stoplamps And Back-Up Lamps
7. To reinstall the lamp assembly, line up and insert the tabs on the back of the assembly in the slots in the fender. Engage the lower clip on the back of the lamp assembly into the fender, keeping the upper tab on the front turn signal/parking lamp assembly inboard of the headlamp bracket tab.
Page 357 4. Remove the bulb holder by pressing the four retaining tabs and pulling the holder away from the assembly. A. Taillamp Bulb B. Back-Up Lamp Bulb C. Turn Signal Lamp Bulb D. Stop/Taillamp Bulb 5. Replace the bulb by pulling the old bulb out and gently pushing the new bulb into the bulb holder socket.
Page 358: Replacement Bulbs
Replacement Bulbs For any bulb not listed here contact your dealer. Lamp Back-up Lamps (3rd from Top) Front Sidemarker Lamps Front Turn Signal/Parking Lamps Headlamps Stop/Taillamps (Top) Taillamps (Bottom) Turn Signal Lamps (2nd from Top) 5-56 Windshield Wiper Blade Replacement Bulb Number Windshield wiper blades should be inspected at least twice a year for wear or cracking.
Page 359 To remove the windshield wiper blade(s): 1. Turn the wipers on to the lowest intermittent setting. 2. Turn the ignition to OFF while the wipers are at the outer position of the wipe pattern. 3. Pull the windshield wiper arm away from the windshield or backglass.
Page 360: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Page 361 (A) Tire Size Code: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size Code” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 362 (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance. For more information, see Uniform Tire Quality Grading on page 5-71 . (G) Maximum Cold Inﬂation Load Limit: Maximum load that can be carried and the maximum pressure needed to support that load.
Page 363 (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 364 (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 365: Tire Size
(F) Tire Size: A combination of letters and numbers deﬁne a tire’s width, height, aspect ratio, construction type and service description. The letter “T” as the ﬁrst character in the tire size means the tire is for temporary use only. (G) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a...
Page 366: Tire Terminology And Deﬁnitions
Light Truck (LT-Metric) Tire (A) Light Truck (LT-Metric) Tire: The United States version of a metric tire sizing system. The letter “LT” as the ﬁrst two characters in the tire size means a light truck tire engineered to standards set by the U. S. Tire and Rim Association.
Page 367 Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.
Page 368 Maximum Loaded Vehicle Weight: The sum of curb weight; accessory weight; vehicle capacity weight; and production options weight. Normal Occupant Weight: The number of occupants a vehicle is designed to seat multiplied by 150 pounds (68 kg). See Loading Your Vehicle on page 4-33 . Occupant Distribution: Designated seating positions.
Page 369: Inﬂation - Tire Pressure
Vehicle Capacity Weight: The number of designated seating positions multiplied by 150 lbs. (68 kg) plus the rated cargo load. See Loading Your Vehicle on page 4-33 . Vehicle Maximum Load on the Tire: Load on an individual tire due to curb weight, accessory weight, occupant weight and cargo weight.
Page 370: When To Check
When to Check Check your tires once a month or more. Also, check the tire pressure of the compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gage to check tire pressure.
Page 371 When rotating your tires, always use the correct rotation pattern shown here. Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Certiﬁcation/Tire label or the Tire and Loading Information label.
Page 372: When It Is Time For New Tires
When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: •...
Page 373: Uniform Tire Quality Grading
CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes may also cause damage to your vehicle.
Page 374 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 375: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance The wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Scheduled wheel alignment and wheel balancing are not needed. However, if you notice unusual tire wear or your vehicle pulling one way or the other, the alignment may need to be reset.
Page 376: Tire Chains
Used Replacement Wheels CAUTION: Putting a used wheel on your vehicle is dangerous. You can’t know how it’s been used or how far it’s been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Page 377 CAUTION: Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate any object only to its recommended pressure. To use your accessory inﬂator system, do the following: 1.
Page 378: If A Tire Goes Flat
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side.
Page 379 CAUTION: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people. You and they could be badly injured or even killed. Find a level place to change your tire. To help prevent the vehicle from moving: 1.
Page 380: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The tools you will need are located in the storage compartment at the rear of the vehicle, on the passenger’s side. To remove the tools, do the following: 1. Remove the side convenience net. 2.
Page 381 The tools you will be using include the jack (A), extension (B) and folding wrench (C). The compact spare tire is located under the rear of the vehicle. See “Compact Spare Tire” later in this section for more information about the compact spare. To remove the compact spare tire, do the following: A.
Page 382 3. To remove the compact spare tire from the cable, tilt the retainer at the end of the cable so it can be pulled up through the wheel opening. 4. If your vehicle is an AWD vehicle, after removing the compact spare tire, turn the wrench clockwise to raise the cable back up.
Page 383: Secondary Latch System
Secondary Latch System Your vehicle may have an underbody mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop a tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down.
Page 384 1. Place the jack under the vehicle, ahead of the rear bumper. Position the center lift point of the jack under the center of the compact spare tire. 2. Turn the folding wrench clockwise to raise the jack until it lifts the secondary latch device under the wheel plate.
Page 385: Removing The Wheel Covers
Removing the Wheel Covers If the wheel has a center cap, use the handle of the folding wrench to pry it off. Then, with the other end of the folding wrench, loosen the nuts. If your vehicle has the plastic bolt-on wheel covers, loosen the bolts completely using the folding wrench, and remove the wheel cover.
Page 386 2. Near each wheel, there is a notch in the vehicle’s body. Position the jack and raise the jack head until it ﬁts ﬁrmly into the notch in the vehicle’s frame nearest the ﬂat tire. Notice: If you use a jack to raise the vehicle without positioning it correctly, you could damage your vehicle.
Page 387 3. Attach the folding wrench to the jack, and turn the wrench clockwise to raise the jack head a few inches. 4. Raise the vehicle by turning the folding wrench clockwise in the jack. Raise the vehicle far enough off the ground so there is enough room for the compact spare tire to ﬁt under the wheel well.
Page 388 7. Install the compact spare tire and put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub. 8. Lower the vehicle by attaching the folding wheel wrench to the jack and turning the wrench counterclockwise.
Page 389: Storing A Flat Or Spare Tire And Tools
Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque speciﬁcation. See “Capacities and Speciﬁcations” in the index for the wheel nut torque speciﬁcation. 10.
Page 390: Storing The Spare Tire And Tools
Storing the Spare Tire and Tools 1. Lay the tire near the rear of the vehicle with the valve stem down. 2. If the vehicle has aluminum wheels, remove the small center cap by tapping the back of the cap with the extension of the shaft.
Page 391 To put the cover back on, line up the tabs on the right of the cover with the slots in the cover opening. Push the cover in place and push down the tab so that it rests in the groove. This secures the cover in place. A.
Page 392 A. Cable C. Door B. Liftgate Hinges Striker 4. Pull the cable through the door striker and the center of the wheel. 5-90 5. Hook the cable onto the outside portion of the liftgate hinges. 6. Pull on the cable to make sure it is secure. 7.
Page 393: Compact Spare Tire
Compact Spare Tire Although the compact spare tire was fully inﬂated when your vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inﬂated.
Page 394: Appearance Care
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into ﬂames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. When you use anything from a container to clean your vehicle, be sure to follow the manufacturer’s warnings and instructions.
Page 395: Special Fabric Cleaning Problems
• Carefully scrape off any excess stain. • Use a clean cloth or sponge, and change to a clean area often. A soft brush may be used if stains are stubborn. • If a ring forms on fabric after spot cleaning, clean the entire area immediately or it will set.
Page 396: Cleaning Vinyl
Cleaning Vinyl Use warm water and a clean cloth. • Rub with a clean, damp cloth to remove dirt. You may have to do this more than once. • Things like tar, asphalt and shoe polish will stain if you do not get them off quickly. Use a clean cloth and vinyl cleaner.
Page 397: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Page 398: Your Vehicle
Before you enter an automatic car wash, if your vehicle is equipped with the optional power sliding door, be sure to have the switch for the power sliding door override feature enabled. See Power Sliding Door (PSD) on page 2-17 . High pressure car washes may cause water to enter your vehicle.
Page 399: Cleaning Aluminum Wheels
Cleaning Windshield, Backglass and Wiper Blades If the windshield is not clear after using the windshield washer, or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full-strength glass cleaning liquid.
Page 400: Cleaning Tires
Cleaning Tires To clean your tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Page 401: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Removes tar, road oil Oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel.
Page 402: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 403: Headlamp Wiring
Headlamp Wiring The headlamp wiring is protected by an internal circuit breaker in the instrument panel fuse panel. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp wiring checked right away.
Page 404: Instrument Panel Fuse Block
Instrument Panel Fuse Block The instrument panel fuse block is located to the right of the glove box on the end of the instrument panel. Pull the door open to access the instrument panel fuse block. 5-102 Fuse Usage Steering Wheel Radio Control BACKLIGHT Switches (Illumination) PCM/PASS...
Page 405 Fuse Usage ® PASS KEY PASS-Key III System PWR LOCK Power Door Locks HTD MIRROR Heated Mirrors RH T/LP Not Used RR FOG LP Not Used CIGAR/DIC/ Cigarette Lighter, DIC, Front APO FRT Auxiliary Power Outlets, Data Link T/SIG Turn Signal Switch Interior Lamp and Multifunction PWR QTR Switch (Power Vent Switch),...
Page 406 Fuse BCM, Electronic Brake Control Indicator Lamp Driver Module, IGN 1 Instrument Panel Cluster, Rear Side Door Actuator Control Module, Rear Windows, Rear Parking Aid RR HVAC Rear HVAC-A/C Control TEMP CONT Rear Window Wiper Motor, RR WPR/ Rear Window Wiper/Washer and WSHR Multifunction Switch (Rear Window Wiper/Washer Switch)
Page 407: Underhood Fuse Block
Underhood Fuse Block This fuse block is located in the engine compartment, in front of the windshield washer ﬂuid reservoir. See Engine Compartment Overview on page 5-12 for more information on location. The fuses marked spare are available if a replacement fuse is needed.
Page 408 Fuse Ignition Switch to Fuses (Instrument Panel): ABS/TCS Ignition, Cruise, DRL, Electronic PRNDL, Ignition 1, AWD, PSD, Air Bag, Turn Signal and Powertrain Control Module [IGN MAIN Relay (Underhood Fuse Block: A/C Clutch, Electronic Ignition, Ignition 1-U/H, INJ, TCC)] Coolant Fans Fuses (Instrument Panel): ABS Module Battery, Cigarette Lighter, Courtesy Lamps, Front Power...
Page 409 Fuse Usage Automatic Transaxle (Torque Converter Clutch Solenoids) Stoplamp Switch to Powertrain Control Module Fuel Pump Relay Powertrain Control Module Not Used Fog Lamp Relay Horn Relay Daytime Running Lamps (DRL) Control Module, Headlamps and Instrument Panel Dimmer Switch Theft-Deterrent Relay to Headlamps Not Used Mini Fuse Puller §...
Page 410: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric measurements. Please refer to Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant Systems Front A/C Front and Rear A/C Automatic Transaxle Pan Removal and Replacement Complete Overhaul AWD Automatic Transaxle...
Page 411: Engine Speciﬁcations
Engine Speciﬁcations Engine VIN Code Transaxle Spark Plug Gap Automatic 0.060 inches (1.52 mm) 5-109...
Page 412 NOTES 5-110...
Page 413 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using Your Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-9 At Each Fuel Fill ...6-9 At Least Once a Month ...6-9 At Least Once a Year ...6-10 Recommended Fluids and Lubricants ...6-12...
Page 414: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended ﬂuids and...
Page 415: Using Your Maintenance Schedule
Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 416: Scheduled Maintenance
If you want to get service information, see Service Publications Ordering Information on page 7-12 . Owner Checks and Services on page 6-9 tells you what should be checked, when to check it and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, ﬂuids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Normal Maintenance Replacement...
Page 417 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. Reset oil life system. See Engine Oil on page 5-13 . An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner ﬁlter.
Page 418: Additional Required Services
Additional Required Services Thefollowing services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components. Replace engine air cleaner ﬁlter.
Page 419: Maintenance Footnotes
Additional Required Services (cont’d) Service Engine cooling system service (or every 5 years, whichever occurs ﬁrst). An Emission Control Service. See footnote (i). Inspect engine accessory drive belt. An Emission Control Service. Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to...
Page 420 (c) Visually inspect hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, ﬁttings and clamps; replace with genuine GM parts as needed. To help ensure proper operation, a pressure test of the cooling system and pressure cap and cleaning the outside of the radiator and air conditioning condenser is recommended at least once a year.
Page 421: Owner Checks And Services
Owner Checks and Services These owner checks and services should be performed at the intervals speciﬁed to help ensure the safety, dependability and emission control performance of your vehicle. Your GM Goodwrench dealer can assist you with these checks and services. Be sure any necessary repairs are completed at once.
Page 422: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Page 423: Ignition Transaxle Lock Check
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition key to LOCK in each shift lever position. • The key should turn to LOCK only when the shift lever is in PARK (P). •...
Page 424: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines Engine Oil starburst symbol.
Page 425 Usage Fluid/Lubricant Carrier Assembly – Differential VERSATRAK™ Fluid (Rear Drive (GM Part No. U.S. 12378514, Module) in Canada 88901045). and Transfer Case (Power Transfer Unit) Hood Latch Assembly, Lubriplate Lubricant Aerosol Secondary (GM Part No. U.S. 12346293, Latch, Pivots, in Canada 992723) or lubricant Spring meeting requirements of NLGI #2, Anchor and...
Page 426: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Part Engine Air Cleaner/Filter Engine Oil Filter Passenger Compartment Air Filter Kit Spark Plugs Windshield Wiper Blades Length Type Wiper Blade (Backglass) Length Type 6-14 ® Part Number ACDelco 25099149 A1208C 25010792 52482929 12568387 41-101 24.0 inches (60.0 cm) Shepherd’s Hook 16.0 inches (40.6 cm) Shepherd’s Hook...
Page 427: Engine Drive Belt Routing
Engine Drive Belt Routing Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-9 can be added on the following record pages.
Page 428: Maintenance Record
Maintenance Record Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 429 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 430 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 431 Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Program for Persons with Disabilities ...7-6 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-8 Vehicle Data Collection and Event Data Records ...7-10 Customer Assistance and Information...
Page 432: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Oldsmobile. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 433 STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce any additional rights you may have.
Page 434: Online Owner Center
1-800-833-OLDS (6537). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Oldsmobile encourages customers to call the toll-free number for assistance. If a U.S. customer wishes to write to Oldsmobile, the letter should be addressed to Oldsmobile’s Customer Assistance Center.
Page 435: United States – Customer Assistance
United States – Customer Assistance Oldsmobile Customer Assistance Center P.O. Box 33171 Detroit, MI 48232-5171 1-800-442-6537 1-800-833-6537 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-442-OLDS (6537) Fax Number: 313-381-0022 From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) Fax Number: 313-381-0022 From U.S. Virgin Islands:...
Page 436: Gm Mobility Program For Persons With Disabilities
Roadside Assistance Program Security While You Travel 1-800-442-OLDS (6537) As the proud owner of a new Oldsmobile vehicle, you are automatically enrolled in the Oldsmobile Roadside Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road.
Page 437 Remember, we are only a phone call away. Oldsmobile Roadside Assistance: 1-800-442-OLDS (6537), text telephone (TTY) users, call 1-888-889-2438. Oldsmobile reserves the right to limit services or reimbursement to an owner or driver when, in Oldsmobile’s judgement, the claims become excessive in frequency or type of occurrence.
Page 438: Courtesy Transportation
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Oldsmobile helps minimize your inconvenience by providing several transportation options. Depending on the circumstances,...
Page 439: Additional Program Information
Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, reimbursement (ﬁve days maximum) may be available for the use of public transportation such as taxi or bus. In addition, should you arrange transportation through a friend or relative, reimbursement for reasonable fuel expenses (ﬁve day maximum) may be available.
Page 440: Vehicle Data Collection And Event Data Records
Vehicle Data Collection and Event Data Records Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in difficult driving situations.
Page 441: Reporting Safety Defects
In addition, once GM collects or receives data, GM may • use the data for GM research needs, • make it available for research where appropriate conﬁdentiality is to be maintained and need is shown, or • share summary data which is not tied to a speciﬁc vehicle with non-GM organizations for research purposes.
Page 442: Reporting Safety Defects To The Canadian Government
General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-442-6537, or write: Oldsmobile Customer Assistance Center P.O. Box 33171 Detroit, MI 48232-5171 7-12 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 443: Service Bulletins
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
Page 444 NOTES 7-14...
Page 445 Accessory Inﬂator ... 5-74 Accessory Power Outlets ... 3-27 Adding Washer Fluid ... 5-37 Additional Program Information ... 7-9 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-100 Adjusting the Captain’s Chairs (Second Row) ... 1-14 Adjusting the Speakers (Balance/Fade) ... 3-66, 3-76 Air Bag Readiness Light ...
Page 446 Audio System(s) (cont.) Theft-Deterrent Feature ... 3-96 Understanding Radio Reception ... 3-98 Automatic Door Locks ... 2-62 Automatic Level Control ... 4-38 Automatic Transaxle Fluid ... 5-19 Operation ... 2-34 Backing Up ... 4-44 Battery ... 5-41 Battery Replacement ... 2-8 Battery Run-Down Protection ...
Page 447 CD Messages ... 3-73, 3-85 Center Passenger Position, Safety Belts ... 1-37 Chains, Tires ... 5-74 Change Engine Oil Message ... 3-56 Charging System Indicator Message ... 3-55 Check Engine Light ... 3-49 Checking Coolant ... 5-24 Checking Engine Oil ... 5-13 Checking Things Under the Hood ...
Page 448 Content Theft-Deterrent System, Arming and Disarming ... 2-67 Control of a Vehicle ... 4-5 Convenience Center ... 2-58 Convenience Net ... 2-56 Coolant Engine Temperature Gage ... 3-48 Engine Temperature Warning Message ... 3-54 Heater, Engine ... 2-33 Cooling System ... 5-28 Cruise Control ...
Page 449 Door (cont.) Power Sliding Door ... 2-17 Power Sliding Warning Message ... 3-57 Programmable Automatic Door Locks ... 2-12 Driver Position, Safety Belt ... 1-28 Driver Information Center (DIC) ... 3-60 Driving At Night ... 4-15 City ... 4-20 Defensive ... 4-2 Drunken ...
Page 450 Engine Speciﬁcations ... 5-109 Entering Programming Mode ... 2-61 Entertainment System ... 3-85 Cleaning the Video Screen ... 3-100 Cleaning Your DVD Player ... 3-100 DVD Distortion ... 3-98 Entry Lighting ... 3-19 ® Erasing HomeLink Buttons ... 2-50 Event Data Records (EDR) ... 7-10 Exit Lighting ...
Page 451 Gage Engine Coolant Temperature ... 3-48 Fuel ... 3-52 Speedometer ... 3-43 Garage Door Opener ... 2-47 Gasoline Octane ... 5-4 Speciﬁcations ... 5-5 Gate Operator and Canadian Programming ... 2-50 Glove Box ... 2-51 GM Mobility Program for Persons with Disabilities ...
Page 452 If No Steam Is Coming From Your Engine ... 5-27 If Steam Is Coming From Your Engine ... 5-26 If the Light Is Flashing ... 3-50 If the Light Is On Steady ... 3-50 If You Are Caught in a Blizzard ... 4-28 If You Are Stuck in Sand, Mud, Ice or Snow ...
Page 453 Lockout Deterrent ... 2-63 Lockout Protection ... 2-13 Locks Automatic Door ... 2-62 Door ... 2-9 Last Door Closed Locking ... 2-12 Leaving Your Vehicle ... 2-13 Lockout Protection ... 2-13 Power Door ... 2-11 Programmable Automatic Door Locks ... 2-12 Loss of Control ...
Page 454 Mirrors Manual Rearview Mirror ... 2-44 Outside Convex Mirror ... 2-45 Outside Heated Mirrors ... 2-45 Outside Power Mirrors ... 2-44 MyGMLink.com ... 7-4 New Vehicle Break-In ... 2-30 Normal Maintenance Replacement Parts ... 6-14 Odometer ... 3-43 Off-Road Recovery ... 4-12 Engine ...
Page 455 ® PASS-Key III Security Message ... 3-58 Plan Ahead When Possible ... 7-8 Playing a Cassette Tape ... 3-69 Playing a CD ... 3-71, 3-80 Playing a Speciﬁc Loaded CD ... 3-81 Playing the Radio ... 3-64, 3-74 Power Accessory Outlets ... 3-27 Door Locks ...
Page 456 Rear Seat Passengers, Safety Belts ... 1-39 Rear Seat Radio Controls ... 3-93, 3-95 Rear Storage Area ... 2-56 Rear Window Defogger ... 3-30, 3-33 Rearview Mirrors ... 2-44 Reclining Seatbacks ... 1-6 Recommended Fluids and Lubricants ... 6-12 Recreational Vehicle Towing ... 4-31 Remote Alarm ...
Page 457 Safety Belt Pretensioners ... 1-45 Reminder Light ... 3-44 Safety Belts Care of ... 5-95 Center Passenger Position ... 1-37 Driver Position ... 1-28 How to Wear Safety Belts Properly ... 1-27 Questions and Answers About Safety Belts ... 1-27 Rear Safety Belt Comfort Guides for Children and Small Adults ...
Page 458 Service Engine Soon Light in the United States or Check Engine Light in Canada ... 3-49 Service Manuals ... 7-12 Setting Preset PTYs (RDS Only) ... 3-78 Setting Preset Stations ... 3-65, 3-75 Setting the Temperature ... 3-36, 3-38 Setting the Time ... 3-63 Setting the Tone (Bass/Treble) ...
Page 459 Taillamps Turn Signal, Stoplamps and Back-up Lamps ... 5-54 TCS Warning Light ... 3-47 Theft-Deterrent, Radio ... 3-96 Theft-Deterrent Systems ... 2-26 Content Theft-Deterrent ... 2-26 ® PASS-Key III ... 2-28 ® PASS-Key III Operation ... 2-28 Tilt Wheel ... 3-7 Tire Sidewall Labeling ...
Page 460 Transmission, Transaxle, Transfer Case Unit Repair Manual ... 7-12 Transportation Options ... 7-8 Trip Computer ... 3-62 Turn and Lane-Change Signals ... 3-8 Turn Signal/Multifunction Lever ... 3-8 Turn Signals When Towing a Trailer ... 4-44 Ultrasonic Rear Parking Assist (URPA) ... 3-24 Underhood Fuse Block ...
Page 461 Vehicle Personalization (cont.) Exiting Programming Mode ... 2-69 Last Door Locking and Lockout Deterrent ... 2-63 Memory Seat ... 2-70 Remote Driver Unlock Control ... 2-64 Remote Lock and Unlock Conﬁrmation ... 2-65 Vehicle Storage ... 5-42 Ventilation Adjustment ... 3-34 Video Screen ...
Page 462 When to Check Power Steering Fluid ... 5-36 When to Inspect the Engine Air Cleaner/Filter ... 5-18 When You Are Ready to Leave After Parking on a Hill ... 4-46 Where to Put the Restraint ... 1-55 Why Safety Belts Work ... 1-24 Windows ...

Oldsmobile 2004 Silhouette Owner's Manual

Table of Contents

Seats and Restraint Systems

Features and Controls

Section 2 Features and Controls

Storage Areas

Vehicle Personalization

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages and Indicators

Message Center

Maintenance Schedule

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Oldsmobile 2004 Silhouette

Summary of Contents for Oldsmobile 2004 Silhouette