Related Manuals for BBT 9000 Series
Summary of Contents for BBT 9000 Series
- Page 1 OWNER’S MANUAL Assembly & Operating Instructions GARDEN MULCHER / CHIPPER MODEL NO. BBT-CH-15 9000 Series Electric Start Garden Mulcher / Chipper...
-
Page 2: To The Owner
Customer Support Please do NOT return the Mulcher without first contacting the Customer Support Department at bbt@bbta.com.au. If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this Mulcher, please contact our Customer Support Department. -
Page 3: Table Of Contents
Changing or Tightening the Belt ..............14 Cleaning the Chipper/Shredder................ 15 Storing the Chipper/Shredder ................15 TROUBLESHOOTING ................16 WARRANTY & SERVICE ................17 SPECIFICATIONS ..................17 EXPLODED DIAGRAM & PARTS LIST..........18-19 YOU MAY ALSO LIKE ................20 BBT-CH-15 WWW.BBTA.COM.AU... -
Page 4: Important Safety Information
Equipment described within this manual may be optional. Some illustrations may not be applicable to your machine. WARNING! Your Responsibility—Restrict the use of this power machine to persons who have read, understood and will follow the warnings and instructions in this manual and on the machine. SAVE THESE INSTRUCTIONS! WWW.BBTA.COM.AU BBT-CH-15... -
Page 5: Key To Symbols
DO NOT operate this machine unless the chute deflector has been installed properly. DO NOT deposit branches larger than 85mm into the top chute. DO NOT force the branches into this machine; allow the machine to automatically feed through. BBT-CH-15 WWW.BBTA.COM.AU... -
Page 6: Safety Information
Allow machine to cool at least 5 minutes before storing. 8. NEVER attempt to make any adjustments while the engine (motor) is running (except where specifically recommended by the manufacturer). WWW.BBTA.COM.AU BBT-CH-15... -
Page 7: Safety Label Locations
Remove the front support pin and tube. Open the bottom section of the discharge chute fully. Line up the holes in the front support leg with those in the bottom discharge chute. Re-insert the front support tube and pin with the bolts to secure the support leg. Tighten. 7. Attach Hopper and discharge chute. BBT-CH-15 WWW.BBTA.COM.AU... -
Page 8: Operating Guidelines
Always wear hearing and eye protection while operating this machine or if you are within 25 metres of this machine. WWW.BBTA.COM.AU BBT-CH-15... -
Page 9: Operating Instructions
DO NOT attempt to shred or chip any material other than normal yard vegetation found (i.e., branches, leaves, twigs, etc.) IMPORTANT: For best performance, it is also important to keep the chipper blade sharp. BBT-CH-15 WWW.BBTA.COM.AU... -
Page 10: Assembly
DO NOT place hands or any other body parts within a radius of cutter wheel rotary. DO NOT touch the blades with your hands or any other body parts. 1. Inflatable Wheels 3. Bolt M8X20 5. Flat Washer 7. Bolt M8X25 2. Flat Washer 4. Nut 6. Shock Pad WWW.BBTA.COM.AU BBT-CH-15... - Page 11 Step 2: Connect the hinge of hopper (12) and discharge port (13) to the crusher room frame and affix with bolt (7). 8. Frame 10. Cutter Wheel 12. Hopper 14. Spring Washer 9. Motor 11. Belt Cover 13. Discharge Port BBT-CH-15 WWW.BBTA.COM.AU...
- Page 12 (16) by using knob (17) to fix it tightly. When fixing the Hand wheel (18) please ensure that the keyways on both the handle (18) and the Frame are aligned and connect properly. Using both Bolt (3) Washer (2) to attach the hand wheel in place (18). 15. Crusher Room 16. Handle 17. Knob 18. Hand Wheel WWW.BBTA.COM.AU BBT-CH-15...
-
Page 13: Maintenance And Storage
8. If the fuel tank has to be drained, do this outdoors. 9. Observe proper disposal laws and regulations for petrol, oil, etc. to protect the environment. Always stop engine, disconnect spark plug and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. BBT-CH-15 WWW.BBTA.COM.AU... -
Page 14: Removing And Sharpening The Blade
• Tighten the engine mounting bolts securely. • Re-install the belt and verify the tension. If the belt is still too loose, move the engine back another 3mm by repeating the above steps. • Reinstall guards and chute. WWW.BBTA.COM.AU BBT-CH-15... -
Page 15: Cleaning The Chipper/Shredder
Store unit in a clean, dry area. Do not store next to corrosive materials such as fertilizer. • NEVER store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc. BBT-CH-15 WWW.BBTA.COM.AU... -
Page 16: Troubleshooting
3. Low engine RPM. 3. Always run engine at full throttle. Rate of discharge slows 1. Low engine RPM. 1. Always run engine at full throttle. 2. Chipper blade dull. 2. Replace chipper blade or see your authorised service dealer. WWW.BBTA.COM.AU BBT-CH-15... -
Page 17: Warranty & Service
Parts purchases, consumable components and accessories such as chains, carry bags, batteries, hoses, grinding discs, covers, belts, cable, wheels and blades are not covered by standard warranty. Spare Parts Spare parts are available. Please see our website (www.bbta.com.au) or contact us at bbt@bbta.com.au for more details. BBT-CH-15... -
Page 18: Exploded Diagram & Parts List
SP-CH-15-034 Vice Belt Cover Board Components SP-CH-15-072 Tapping Screw SP-CH-15-035 Belt SP-CH-15-073 Screw Thread SP-CH-15-036 Hexagon Head Bolt SP-CH-15-074 Self-Lock Button SP-CH-15-037 Flat Washer SP-CH-15-075 Hitch Trailer SP-CH-15-038 Vice Belt Cover Board Fixed Plate SP-CH-15-076 Hexagon Head Bolt WWW.BBTA.COM.AU BBT-CH-15... - Page 19 EXPLODED DIAGRAM & PARTS LIST BBT-CH-15 WWW.BBTA.COM.AU...
-
Page 20: You May Also Like
YOU MAY ALSO LIKE Chainsaws Cultivators / Tillers Lawn Mowers Log Splitters COPYRIGHT © BIGGER BOYZ TOYZ AUSTRALIA PTY Unit 2/3 Delta Place Albion Park Rail NSW 2527 BBT-CH-15-MNL1902...