Related Manuals for SATO SK-270WP
Summary of Contents for SATO SK-270WP
- Page 1 Instruction Manual Waterproof Digital Thermometer Model SK-270WP No. 8078-00 with a hole for wall-mount type No. 8078-20 without a hole for wall-mount type S.01E...
- Page 3 - Read this manual thoroughly before using the thermometer. Keep the manual in a safe place for future references whenever necessary. Warning The SK-270WP thermometer is not explosion-proof. Never use it in an atmosphere containing flammable gases. Beware of explosion! There is a risk of explosion.
- Page 4 ** For repair or calibration, contact us or the dealer from which the unit was purchased. 2. Overview The SK-270WP is waterproof digital thermometer to which a dedicated thermistor sensor probe can be connected. Optional probes can be interchangeably connected with main unit.
- Page 5 4. Features - Various display function Maximum (MAX) and minimum (MIN) temperature can be displayed and measured value can be held (HOLD). - HACCP function Heating temperature and countdown of heating time settings are possible. When the setting time elapses, buzzer sounds and LED lights. - Waterproof function When connecting the main unit and the probe, it conforms to “Protection level IP67 in JIS C 0920”...
- Page 6 5. Names of Section ■ Front view ■ Rear view (No. 8078-22 does not have the hole for wall-mount) Hole for wall-mount Connecter for probe SK-270WP Display section Key operation section Lid of battery compartment Protection rubber Hook for neck strap 5-1.
- Page 7 5-2. Key operation section ③ ② ① ⑤ ④ ① POWER key - Press this key to turn the main unit on. Press the key again to turn it off. ② MODE key - Use this key to ensure the setting value. In the HACCP mode, press this key to select mode. ③...
- Page 8 Cautions ⚫ Firmly attach the battery lid putting the rubber packing in the groove and secure the screw. Otherwise, waterproofness will not be guaranteed. ⚫ The replacement batteries must be new and of the same type. Mixed use of different types or new and old batteries could cause an explosion or leakage.
- Page 9 (3) To disconnect the probe, turn the nut counterclockwise to remove it. Then pull the probe connector straight out. Important: To protect the temperature probe, make sure that the unit is turned off before installing or removing the probe. Cautions ⚫...
- Page 10 Cautions - Be careful not to burn yourself when measuring high temperature. - If you need to measure both objects having a large difference (high and low temperatures), do not continuously carry on both measurements. Return the temperature of the temperature sensor (probe) to the normal temperature once and then start next measurement.
- Page 11 ① Temperature measurement mode: measures temperature ② Setting mode: performs in HACCP function, the temperature value setting countdown time setting and buzzer setting, ③ Max/Min. display mode: Max. and Min. values are indicated after the power is ON. ④ HACCP mode: puts the Timer in action following the temperature and time to be set in the setting mode.
- Page 12 7-5. HACCP function This function notifies you when the temperature and the heating time set for the object being measured are reached, by sounding the buzzer and/or turning on the LED. It is useful, for example, when controlling the heating time of food. Setting Temperature, time and buzzer ON/OFF that are controlled in the HACCP mode can be set.
- Page 13 ④ The initial value for temperature (°C) of HACCP3 is set to "100". If the change is necessary, set the temperature and time as desired. If HACCP3 is not to be used, press the MODE key three times. The unit enters the buzzer setting.
- Page 14 8. Warnings for low battery When the batteries are exhausted, mark will blink. Place the batteries with new ones. Otherwise, measured value may display incorrectly. 9. Error Message If an error occurs, one of the error codes below will be shown on the temperature display section. Error code Causes Remedy...
- Page 15 10. Specifications Cat. No. No. 8078-00 No. 8078-20 Model Waterproof Digital Thermometer SK-270WP 〇 × Hole for wall-mount Display range -50.0 to 300.0°C (Measuring range is different depending on the probes connected) Display Accuracy When operation ambient is 0 to 40°C ±...
- Page 16 3-4, Kanda-kajicho, Chiyoda-ku, Tokyo 101-0045 Japan URL: http://www.sksato.co.jp/english/...
Need help?
Do you have a question about the SK-270WP and is the answer not in the manual?
Questions and answers