1 Safety Precautions 1.1. General Guidelines 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical...
2 Warning 2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
A replacement fuse cover can be purchased from your local Panasonic Dealer. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
“Disassembly and Assembly Instructions.") NOTE: This Lithium battery is a critical component. (Type No.: CGR-F/202AW Manufactured by Panasonic.) (Not supplied) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
However, the AC Adaptor replacement part number is DE-974HC which should be used when ordering. 2. VSK0561 is indicated on AC Adaptor used in the following models: VDR-D220E, VDR-D220EB, VDR-D220EE, VDR-D220EF, VDR-D220EG, VDR-D220EP, VDR-D220GC, VDR-D220GCS, VDR-D220GN, VDR-D220SG, and VDR-D230EE-K. However, the AC Adaptor replacement part number is DE-974GB which should be used when ordering.
5 Service Mode 5.1. Error Display "PUSH THE RESET SWITCH" is displayed automatically on the EVF or the LCD Monitor when an undesirable condition has occurred. Fig. 1 Note: When "PUSH THE RESET SWITCH" is displayed repeatedly, service is required. Check the Error Code which is listed in the Service Menu.
Page 10
Note: Only perform items 1, 3, and 4 in the Service Menu. To select the Item 1. Set to Service Menu. 2. Press [JOYSTICK CONTROL UP/DOWN] to select item [1], [3], or [4]. 3. Press [JOYSTICK CONTROL RIGHT] to display [YES/NO] screen. 4.
6.2. Service Position Caution Laser light striking the eye may cause your eyesight to be lost: For safety, be sure to remove any power supply (AC adaptor/charger, battery, etc.) from the DVD video camera/recorder before starting work. <CSA requirement> CAUTION: VISIBLE LASER RADIATION DO NOT STARE INTO THE BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS CLASS 2M Optical pickup...
6.3. Removal/Installation of F.P.C. From Non ZIF (Zero Insertion Force) Connector Removal/Installation of F.P.C. from the Non ZIF (Zero Insertion Force) connector: 1. The Non ZIF connectors and the ZIF connectors are used on the unit. And there are 2 types (Type A, Type B) of Non ZIF connectors.
6.4. Method for Ejecting the DVD 6.5. EEPROM Data Tray Manually CAUTION: Be sure to save the EEPROM data using PC-EVR Caution Adjustment Program before service and adjustment in Laser light striking the eye may cause your eyesight order to make sure to avoid an accidental data loss, etc. to be lost: For safety, be sure to remove any power supply (AC adaptor/charger, battery, etc.) from the using PC-EVR Adjustment Program by first.
6.6. Special Note All integrated circuits and many other semiconductor devices are electrostatically sensitive and therefore require the special handlings techniques described under "ELECTROSTATICALLY SENSITIVE (ES) DEVICES" section of this service manual.
7 Disassembly and Assembly Instructions 7.1. Cabinet Section 7.1.1. DISASSEMBLY FLOWCHART Caution Laser light striking the eye may cause your eyesight to be lost: For safety, be sure to remove any power supply (AC adaptor/charger, battery, etc.) from the This flow chart indicates the disassembly steps of the DVD video camera/recorder before starting work.
Page 18
7.1.2. Disassembly Method MAIN PARTS PORTION STEP Ref. Section NOTE PART REMOVE (518), (537), 2(519), 2(533), Front/Mic Ass'y FP6501, Hand Strap 2(518), 4(519), Side R & (537), FP81, LCD Ass'y 2(L-1), (Shoe) (537), (16) Rear Case Unit (519), FP11 2(519), (537), Grip/EVF Ass'y FP91 Bottom Ass'y...
Page 19
Note: MAIN PARTS SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2. The parts indicated by the dotted line are for Ass'y only and are not supplied.
Page 20
FRONT/HOOD PORTION STEP Ref. Section PART REMOVE NOTE Front P.C.B. 3(537), FP6502 (For models with Light) 2(537), (54) LED Light F.P.C. (For models with Light) ----- LED Light Lens ----- Front/Hood Unit How to read chart shown above: A: Order of Procedure steps. When reassembling, perform steps(s) in reverse order.
Page 21
FRONT HOOD AND FRONT P.C.B. SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2.
Page 22
SIDE R OPERATION PORTION LCD PORTION STEP Ref. Section STEP Ref. Section NOTE PART REMOVE PART REMOVE NOTE Side R P.C.B. LCD Protector (533) 2(537), P6301 LCD Case A Unit 2(519), 8(L-1) LCD Case B Unit FP8101 How to read chart shown above: A: Order of Procedure steps.
Page 23
Note: SIDE R OPERATION AND LCD SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2.
Page 24
CCD & LENS PORTION STEP Ref. Section NOTE PART REMOVE CCD P.C.B. 2(536) ----- Filter Rubber Optical Filter ----- STEP Ref. Section NOTE PART REMOVE 2(538), Zoom Motor Unit Unsolder 2(538), Focus Motor Unit Unsolder How to read chart shown above: A: Order of Procedure steps.
Page 25
CCD AND LENS SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2. The parts indicated by the dotted line are for Ass'y only and are not supplied.
Page 26
GRIP COVER & EVF PORTION STEP Ref. Section NOTE PART REMOVE EVF Angle Unit 2(537), (L-1) ----- Grip Cover Unit STEP Ref. Section NOTE PART REMOVE (533) Shoe Angle FP8901 EVF Slide Base EVF Lock Plate (L-2) ----- EVF F.P.C. STEP Ref.
Page 27
Note: GRIP COVER AND EVF SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2. The parts indicated by the dotted line are for Ass'y only and are not supplied.
Page 28
Notes in chart 3. Removal of Rear Case Unit 1. Removal of Top Cover Unit 1) Open the LCD and Jack Cover to remove the 6 Screws 1) Remove the Screw (537) and remove the Disc Eject Cover. (518, 519, 533, 537). 2) Pull and slide carefully the Top Cover Unit.
Page 29
5. Removal of Bottom Ass'y 7. Removal of Main P.C.B. 1) Remove the 3 Screws (519). 1) Remove the 3 Screws (519). 2) Remove the Bottom Ass'y to disconnect Connector 2) Disconnect the Zoom Switch F.P.C. from Connector B51 (B to B Connector). FP61.
Page 30
8. DVD Drive Frame Unit Caution Removal of DVD Drive Frame Unit & Disc Cover Lock Unit Caution 1) Remove the 2 Screws (540) and remove the Earth Laser light striking the eye may cause your eyesight Plate. to be lost: For safety, be sure to remove any power 2) Remove the 4 Screws (537) and remove the Heat Sink supply (AC adaptor/charger, battery, etc.) from the Ass'y.
Page 31
9. Installation of Front P.C.B. 10. Removal of Side R P.C.B. 1) Install the Front P.C.B. with the 3 bosses, and tighten 1) Remove the 2 Screws (537). the 3 Screws (537). 2) Disconnect connector lead from Connectors P6301. 2) (For models with Light) Connect the F.P.C.
Page 32
11. Removal of LCD Case B Unit, LCD Case A Unit 12. Installation of LCD Backlight P.C.B., LCD Panel Ass'y, Take care not to damage the F.P.C. LCD Shield Case and LCD Case B 1) Remove the Screw (533). Use extreme care regarding LEDs when handling the LCD 2) Open the LCD and push to remove the LCD Protector.
Page 33
13. Installation of LCD Panel, Reflect Sheet, Lead Light Reflect Sheet Panel, Diffusion Sheet, BEF Sheet, BEF Sheet A and Panel Holder Unit a. When replacing the LCD Panel, the Diffusion Sheet, the BEF Sheet and the BEF Sheet A, make sure to remove the Protection Sheets.
Page 34
14. Removal of CCD P.C.B., Filter Rubber and Optical Filter 16. Installation of Grip Cover Unit CAUTION: 1) Install the Grip Cover Unit with the 3 pins. 1) When removing the CCD P.C.B., take care that the 2) Tighten the 2 Screws (537). Optical Filter does not fall out.
Page 35
17. Installation of EVF F.P.C., EVF Lock Plate, EVF Slide 18. Removal of Eye Cap Base and Shoe Angle Remove the Eye Cap after removing the 2 Screws (533). Take care not to damage the F.P.C. and the Switch. 1) Insert the EVF F.P.C. into the slot and secure it with the 19.
8 Measurements and Adjustments 8.1. Electrical Adjustment 8.1.1. Initial Guideline The table below shows which adjustments are necessary according to the unit parts and individual parts to be replaced. Make sure to perform these adjustments shown below as necessary.
Page 37
8.1.2. Installation of USB-SERIAL driver 6. When EEPROM data has been saved, the menu will appear. Execute the "Setup.exe" file in "ComMass" folder by double To perform each adjustment, display the adjustment menu clicking to install the USB-SERIAL driver. by selecting from "Camera Adjust" or "Video Adjust" and 8.1.3.
9 Maintenance 9.1. Cleaning Lens, Viewfinder and LCD Panel Do not touch the surface of the lens, Viewfinder and LCD Panel with your hand. When cleaning the lens, use air-blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and gently wipe the surface. Note: Lens cleaning paper and lens cleaner are available at camera shops, etc.
10 Troubleshooting VIDEO No picture on both EVF and LCD in Camera Mode Check CCD Unit. Check Connection of CCD FPC (FP31). Re-Insert CCD FPC. Check the waveform of Pin 3, 4, 5, 6, 10, 12, and 13 of FP31 on Main P.C.B. Pin 3 (V1) Pin 4 (V2) Pin 5 (V3)
Page 41
No picture on EVF but LCD is normal Check Connection of EVF FPC (FP91). Re-Insert EVF FPC. Check the OPEN/CLOSE Switch on Side R Shaft Replace Side R Shaft Unit. Unit. Replace Main P.C.B. Check the voltage of Pin 6, 8, 10 and 18 of FP91 on Main P.C.B.
Page 42
No picture on Video Output Jack Check Connection of B51 on Main P.C.B. Re-Insert Connector B51. Check the voltage of Pin 13 of B51 on Main P.C.B. Replace Main P.C.B. Pin 13 (VIDEO): 0.1V Repair Bottom P.C.B.
Page 43
AUDIO No Audio in Camera Mode Check Connection of B51 on Main P.C.B. Re-Insert Connector B51. Check Pin 32 and 34 of B51 (AUDIO_L/R) Pin 32 (AUDIO_R): 0.1V Pin 34 (AUDIO_L): 0.1V Repair Bottom P.C.B. Check Pin 2 and 4 of FP6501 (A_M_OUT_L/R). Repair Front P.C.B.
Page 44
POWER No power Does unit turn on the power with SD Card mode or Check DVD Drive Unit. forced power on function ? <How to turn on with forced power on function> Push and hold the MENU button and JOYSTICK CONTROL RIGHT then Turne on the power with POWER SW.
Page 45
SYSCON Mechanism & Lens Motor lock code is displayed in Service Menu (Refer to "Service Menu.") Zoom Motor Lock (Zoom does not work) Replace Side L Unit. Check Zoom Switch. Re-Insert Lens FPC. Check Connection of Lens FPC (FP71) on Main P.C.B.
Page 46
Focus Motor Lock (Focus does not work) Check Connection of Lens FPC (FP71) on Main Re-Insert Lens FPC. P.C.B. Check waveform of Pin 9 and 10 of FP71 on Main P.C.B. Main P.C.B. is suspicious as Pin 9 (F-ENC): Is waveform repeat "High" and "Low" when power ON ? a cause of Focus Motor Lock.
Page 47
Operation Key does not work Check voltage of Pin 24 of FP61 on Main P.C.B. Replace Main P.C.B. Pin 24 (MODE_VDD): 2.8V Replace Side L Operation Unit. Check Key operation. Check voltage of FP61 as following voltage chart. Replace Main P.C.B. Operation Key Pin No.
Page 48
DVD DRIVE UNIT How to confirm which there is malfunction in Main P.C.B. or DVD Drive Unit. Does a power turn on with Disc REC or PLAY When install normal Disc, any error message mode ? is display ? Replace Main P.C.B. Does unit turn on the power with SD Card mode or forced power on function ? <How to turn on with forced power on function>...
12 Block Diagrams OVERALL BLOCK DIAGRAM REAR UNIT MAIN P.C.B. IC1001, ETC SIDE L/OPERATION UNIT IC6004 IC6001 BATTERY FP11 EEPROM SERIAL DATA/CLOCK TERMINAL +3.3V EEPROM FP61 UNREG AUTO FOCUS SW POWER CROSS KEY DC JACK IC6002 SUPPLY +1.8V MANUAL FOCUS SW MODE DIAL KEY TIMER SERIAL DATA/CLOCK +1.2V...
13 Schematic Diagrams 13.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT NOTES 1. Important safety notice 3. Parts marked "PT" are not used in any models included in this service model. Components identified by the sign have special characteristics important for safety. When replacing any C6011 C6011 R6097...
13.2. FRONT SCHEMATIC DIAGRAM FRONT SCHEMATIC DIAGRAM NOTE: NOTE: NOTE: For placing a purchase order of the parts, PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list. REFER TO BEGINNING OF SCHEMATIC SECTION.
13.3. BOTTOM SCHEMATIC DIAGRAM BOTTOM SCHEMATIC DIAGRAM NOTE: NOTE: IMPORTANT SAFETY NOTICE: NOTE: For placing a purchase order of the parts, COMPONENTS IDENTIFIED BY THE SIGN HAVE PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list.
13.4. LCD BACKLIGHT SCHEMATIC DIAGRAM LCD BACKLIGHT SCHEMATIC DIAGRAM NOTE: NOTE: NOTE: NOTE: For placing a purchase order of the parts, ALL INDIVIDUAL PARTS EXCEPT D8101, D8103, D8105, AND D8107 PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list.
13.5. SIDE R / EVF FPC / EVF BACKLIGHT SCHEMATIC DIAGRAMS NOTE: NOTE: NOTE: For placing a purchase order of the parts, PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list. REFER TO BEGINNING OF SCHEMATIC SECTION.
13.6. CCD / REAR CASE / LCD SW SCHEMATIC DIAGRAMS NOTE: NOTE: NOTE: For placing a purchase order of the parts, PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list. REFER TO BEGINNING OF SCHEMATIC SECTION.
13.7. SIDE L/OPERATION / DISK COVER LOCK SCHEMATIC DIAGRAMS NOTE: NOTE: NOTE: For placing a purchase order of the parts, PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list. REFER TO BEGINNING OF SCHEMATIC SECTION.
13.8. INTERCONNECTION SCHEMATIC DIAGRAM INTERCONNECTION SCHEMATIC DIAGRAM NOTE: NOTE: NOTE: For placing a purchase order of the parts, PARTS MARKED "PT" ARE NOT USED. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, be sure to use the part number listed in the parts list. REFER TO BEGINNING OF SCHEMATIC SECTION.
14 Printed Circuit Board 14.1. FRONT P.C.B. FRONT P.C.B. LSEP8375A1 VDR-D220EG/EF/E/EP/EB/GC/GCS NOTE: NOTE: CIRCUIT BOARD LAYOUT SHOWS COMPONENTS INSTALLED FOR VARIOUS MODELS. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, FOR PROPER PARTS CONTENT FOR THE MODEL YOU ARE SERVICING, REFER TO BEGINNING OF SCHEMATIC SECTION.
14.2. BOTTOM P.C.B. BOTTOM P.C.B. LSEP8376A1 IMPORTANT SAFETY NOTICE: NOTE: COMPONENTS IDENTIFIED BY THE SIGN HAVE FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, (COMPONENT SIDE) SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. REFER TO BEGINNING OF SCHEMATIC SECTION. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS.
14.3. LCD BACKLIGHT P.C.B. LCD BACKLIGHT P.C.B. LSEP8367B1 NOTE: NOTE: NOTE: CIRCUIT BOARD LAYOUT SHOWS COMPONENTS INSTALLED FOR VARIOUS MODELS. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, ALL INDIVIDUAL PARTS EXCEPT D8102, D8104, D8107, D8109 AND D8111 FOR PROPER PARTS CONTENT FOR THE MODEL YOU ARE SERVICING, REFER TO BEGINNING OF SCHEMATIC SECTION.
14.4. SIDE R P.C.B. SIDE R P.C.B. LSEP8377A1 NOTE: NOTE: NOTE: MULTILAYER P.C.B. CIRCUIT BOARD LAYOUT SHOWS COMPONENTS INSTALLED FOR VARIOUS MODELS. FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES, FOR PROPER PARTS CONTENT FOR THE MODEL YOU ARE SERVICING, REFER TO BEGINNING OF SCHEMATIC SECTION.
15 Exploded View 15.1. MAIN PARTS SECTION Note: MAIN PARTS SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2.
15.2. FRONT CASE, MAIN P.C.B. AND JACK P.C.B. SECTION FRONT HOOD AND FRONT P.C.B. SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list.
15.3. SIDE CASE R AND LCD SECTION Note: SIDE R OPERATION AND LCD SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2.
15.4. CCD AND LENS SECTION CCD AND LENS SECTION Note: 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2.
15.5. REAR CASE AND EVF SECTION Note: GRIP COVER AND EVF SECTION 1. Parts with no Ref. No. in "EXPLODED VIEW" are not supplied. And some Ref. No. will be skipped. Be sure to make your orders of replacement parts according to the parts list. 2.
15.6. PACKING PARTS AND ACCESSORIES SECTION PACKING PARTS AND ACCESSORIES SECTION IMPORTANT SAFTY NOTICE: COMPONENTS IDENTIFIED BY THE SIGN HAVE SPECIAL CHARACTERISTICS IMPORTANT FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SPECIFIED PARTS. not supplied (VDR-D228GK) (VDR-D220EB/GC/GCS/SG) (VDR-D220GN) (VDR-D220EG/EF/E/ not supplied...
1. Parts with mark "SPC" in the Remarks column are supplied from Spare Parts Center of Panasonic AVC 2. IMPORTANT SAFETY NOTICE Company. Components identified by the sign have special 2.
Page 72
Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks LSYK1944 GRIP COVER UNIT 220EG/E DE-974GC AC ADAPTOR F/E/EP/ 220EG/E EB/GC/G F/E/EP/ CS/SG/E EB/GC/G E/GN,22 CS/SG/E E/GN,23 LSYK1994 GRIP COVER UNIT 230EE DE-974HC AC ADAPTOR LSYK1954 SIDE R/SHAFT UNIT 220EG/E...
Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks LSEP8374Q1 MAIN P.C.B. LSEP8374R1 MAIN P.C.B. E.S.D. 220GC/G CS/SG/E 230EE E/GN,22 LSEP8375A1 FRONT P.C.B. 220EG/E LSEP8374R1 MAIN P.C.B. F/E/EP/ 230EE EB/GC/G CS/SG/E LSEP8375A1 FRONT P.C.B. E/GN,22 220EG/E F/E/EP/...
Page 74
RESISTORS MISCELLANEOUS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R4802 ERJ3GEYJ472V MGF CHIP 1/16W 4.7K LSSC0928 GROUNDING PLATE,STEEL R4803 ERJ3GEYJ223V MGF CHIP 1/16W 22K LSMG0136 MIC DAMPER R4804 ERJ3GEYJ333V MGF CHIP 1/16W 33K LSEK0695 MIC DEVICE UNIT R4805...
Page 75
BATTERY FPC CONNECTORS Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks BT7001 ML-621S/F9DE BATTERY FP8101 K1MN22BA0197 CONNECTOR 22P FP8102 K1MN24BA0196 CONNECTOR 24P MISCELLANEOUS Ref. Part No. Part Name & Description Remarks 16.2.5. SIDE R P.C.B. U7001 K1NA09E00084 SD UNIT...