Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for unicraft ESW 900
Summary of Contents for unicraft ESW 900
- Page 1 Operating Instructions Electric Wire Rope Hoist ESW 900 ESW 900...
-
Page 2: Table Of Contents
13.2 Spare parts drawing ........16 itly permitted. Contraventions are liable to compensa- 13.3 Electrical wiring diagram ........ 17 tion. 14 EC Declaration of Conformity ......18 Subject to technical modifications and error. 15 Maintenance plan ..........19 ESW 900 | Version 2.04... -
Page 3: Introduction
WARNING! This combination of symbol and signal words indi- cates a potentially dangerous situation which may lead to death or severe injury if not avoided. ESW 900 | Version 2.04... -
Page 4: Obligations Of The Operating Company
- The operator must have all safety devices protection of the user, the staff or for third parties. checked regularly for their good working order and their integrity. ESW 900 | Version 2.04... -
Page 5: Requirements To Staff
Certain works may only be performed by specialist per- sonnel of the manufacturer. Other personnel is not au- thorized to perform these works. Please contact our cus- tomer service for the execution of all arising work. ESW 900 | Version 2.04... -
Page 6: General Safety Regulations
It is the responsibility of the operator to insist that oper- ating personnel must wear protective clothing wherever All persons working with the wire rope hoist must be necessary. aware of these residual risks and follow the instructions ESW 900 | Version 2.04... -
Page 7: Technical Data
This causes different re- sidual risks and hazard potentials each operator must be aware of. Technical data ESW 900 Fig. 1: Electric wire rope hoist type plate ESW 900 Maximum load [kg] Transport, packaging, storage cable length [m] cable thickness [mm] 5.1 Transport... -
Page 8: Description Of The Device
Injuries to hands and fingers may result from - Only loads which do not exceed the load-bearing improper use of the electric wire rope hoist. capacity may be suspended. - Never grasp the cable while the equipment is in op- eration. ESW 900 | Version 2.04... - Page 9 Abb. 4: correct winding of the cable Risk of crushing! Injuries to hands and fingers may result from improper use of the electric wire rope hoist. - Never grasp the cable while the equipment is in op- eration. ESW 900 | Version 2.04...
-
Page 10: Operating Conditions
- The means of attachment (eyelet, cable or similar) must sit loosely in the base of the hook. - The point of the hook must not bear the load. - Close the safety catch. ESW 900 | Version 2.04... -
Page 11: Care, Maintenance And Repair
Collect the cleaning rags or the cleaning wool in one suitable, closed container to ensure that they are disposed of environmentally friendly. - Do not throw them into the normal household waste. ESW 900 | Version 2.04... - Page 12 ESW 900 | Version 2.04...
- Page 13 10%. ATTENTION! Fig. 7: Dimension of the hook - part 2 Only genuine replacement parts from the manufac- turer of the wire rope hoist should be used. ESW 900 | Version 2.04...
-
Page 14: Testing The Wire Rope Hoist
Motor is wet. Humidity is too high or water ingress. Drain the water. Dry the device. After that start the motor and let it operate for a little while. Repeat this proce- dure a few times. ESW 900 | Version 2.04... -
Page 15: Spare Parts
Load hooks for the electric wire rope hoist must be or- dered. DANGER! Danger of injury by the use of wrong spare - Type of device: Electric wire rope hoist ESW 900 parts! - Item number:6190900 Dangers may result for the user and damages as - Position No.: 18... -
Page 16: Spare Parts Drawing
In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 10: Spare parts drawing ESW 900 | Version 2.04... -
Page 17: Electrical Wiring Diagram
Spare parts 13.3 Electrical wiring diagram ESW 900 Fig. 11: wiring diagram ESW 900 ESW 900 | Version 2.04... -
Page 18: Ec Declaration Of Conformity
DIN EN ISO 12100-1:2011 Safety of machines - General principles of design - Risk evaluation and risk reduction Technical services, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Person responsible for the documentation: Hallstadt, 18/04/2016 ______________________ Kilian Stürmer Manager ESW 900 | Version 2.04... -
Page 19: Maintenance Plan
Maintenance plan 15 Maintenance plan Maintenance plan ESW 900 40 h 200 h 200 h As nec- As nec- As nec- annu- essary essary essary ally Date operating Employee Signature hours ESW 900 | Version 2.04... - Page 20 www.unicraft.de...