Sealey LED036 Instruction Manual

thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give
you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
 WARNING! Disconnect lamp from mains power
before performing any maintenance.
 DO NOT shine lamp directly into your, other person's
or animal's eyes.
 DO NOT allow children to use the lamp.
 Maintain the lamp in good condition.
 DO NOT use the lamp if the lamp if damaged.
 When not in use store the light in a safe, dry,
childproof location.
 WARNING! Ensure Health and safety, local authority
and general workshop practice regulations are
adhered to when using this light.
 Wear eye protection. A full range of safety equipment
is available from your sealey dealer.
 Wear suitable clothing to avoid snagging.
 DO NOT wear jewellery and tie back long hair.
 Account for all tools being used and DO NOT leave
them in or near the engine.
1.2. ELECTRICAL SAFETY FOR USE OF
TRANSFORMER. USE ONLY THE SUPPLIED
TRANSFORMER PLUG FOR CONNECTING LAMP TO THE POWER
SUPPLY.
 WARNING! It is the user's responsibility to read, understand and
comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installa-
tion of appropriate safety devices. An rccB (residual current circuit
Breaker) should be incorporated in the main distribution board. We also
recommend that an rcD (residual current Device) is used with all
electrical products, particularly portable equipment which is plugged into
an electrical supply not protected by an rccB.
You must also read and understand the following
instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical
appliances, if used on business
premises, to be tested by a qualified electrician, using a Portable
Appliance tester (PAt), at least once a year.
 WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and sit-
uations that may occur. It must be understood that common sense and caution are factors which must be applied by the operator.
© Jack sealey Limited
InstructIon MAnuAL for:
UNDER BONNET CORDLESS 36 SMD
RECHARGEABLE LAMP LITHIUM-ION
MODEL NO : LED036
1.2.2. The Health & Safety at Work Act 1974 makes owners of electri-
cal appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical
safety,
contact a qualified electrician.
1.2.3. You must ensure that you:
 Inspect the transformer plug, cable and connector for
wear and damage to ensure items are safe before
connecting to the mains power supply. If worn or
damaged DO NOT use.
 Important: check that the voltage marked on the
transformer plug is the same as the power supply to
be used.
 uncoil the cable between transformer plug and lamp.
 DO NOT pull the transformer plug from the mains
socket by the lead.
 DO NOT use any other type of transformer with this
product.
 DO NOT try to take the transformer plug apart.
 DO NOT use the transformer plug to power any other
electrical item.
 DO NOT get the transformer plug wet, or use in
wet, damp conditions (for indoor use only).
 WARNING! NEVER substitute a standard 13amp
3 pin plug, or any other type of plug, for the
transformer plug.
this transformer plug reduces and rectifies the mains
voltage (230 volts Ac) to 12 volts DC.
Original Language Version
Fig.2
Fig.1
LED036 Issue: 1 - 13/02/13