Page 1
V E Y O R S V E Y O R S Industrial Conveyor Specialists Installation, Maintenance & Parts Manual MODEL 110 & 111 V-BELT SLIDER BED CONVEYOR For Additional copies of this manual, please visit our website at www.titanconveyors.com...
Page 2
Page 14 ..............Model 111 Blow Apart Drawing (A) Seller warrants that the material in and the workmanship on the equipment manufactured by TITAN will be free from defects at time of shipment. If during the first year from the date of shipment, the Buyer establishes to the seller’s satisfaction that any part or parts manu- factured by TITAN were defective at the time of shipment, TITAN will, at its own expense, repair or replace (but not install) replacement parts.
Page 3
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
Page 4
Titan at 920-982-6600. I. RECEIVING Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any components are missing, contact Titan IMMEDIATELY with a description of the missing components along with the conveyor serial number(s).
Page 5
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
Page 6
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
Page 7
V E Y O R S V E Y O R S V E Y O R S Model 110 & 111 Belt Threading Model 110 Bottom Mount Drive Model 110 Center Drive & Take-up Model 111 Bottom Mount Drive Model 111 Center Drive &...
Page 8
V E Y O R S V E Y O R S V E Y O R S IN REF. TO LEFT HAND AND RIGHT HAND SIDES, WE AT TITAN INDUSTRIES CAUTION ALWAYS POSITION OURSELF STANDING AT THE INFEED, LOOKING AT THE...
Page 9
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...
Page 10
2. VENTILATION - During normal operation gear reducers build up heat and pressure that MUST be vented to protect the seals and gears. If not installed at Titan, a brass vent plug contained in a small plastic bag, will be put in a box or larger bag along with fasteners sent loose for use during field installation.
Page 11
V E Y O R S BEARINGS LUBRICATION - Bearings used on Titan Conveyors are normally pre-lubed for life. If customer requested, re-lube bearings are provided, the use of a #2 consistency lithium based grease is advised. Greasing Frequency should be as many times as necessary to maintain a small film of grease leaking at the seals.
Page 12
SHUT OFF CONVEYOR BEFORE USING OIL CAN OR BRUSH TO APPLY OIL! REMEMBER - ALL GUARDS AND BOTTOM PANS, IF PROVIDED, MUST BE REPLACED BEFORE RUNNING CONVEYOR. TITAN INDUSTRIES IS NOT DANGER RESPONSIBLE FOR INjURIES CAUSED BY NOT COMPLYING WITH SAFETY INSTRUCTIONS.
Page 13
V E Y O R S V E Y O R S V E Y O R S Model 110 V-Belt Slider Bed Belt Conveyor V E Y O R S V E Y O R S V E Y O R S...
Page 14
V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S V E Y O R S...