Introduction; Ii. Installation; Frame Assembly - Titan 630 Installation, Maintenance & Parts Manual
Hinged steel belt conveyor
Hide thumbs
Also See for 630:
- Operating manual (84 pages) ,
- Installation, maintenance & parts manual (15 pages)
Table of Contents
Advertisement
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
INTRODUCTION
The management and employees of Titan Industries thank you for specifying Titan equipment. This manual will give
you the basic information to install and maintain your equipment. If special circumstances or questions come up
call Titan at 920-982-6600.
I. RECEIVING
Upon delivery of your Titan conveyor, check the packing slip or bill of lading accompanying the unit. If any
components are missing, contact Titan IMMEDIATELY with a description of the missing components along with
the conveyor serial number(s). The serial number is found on the serial plate normally positioned by the
Check the unit(s) over carefully upon arrival for damage. If you find any damage note it on the bill of lading.
YOU MUST also file a claim IMMEDIATELY with the carrier.
II. INSTALLATION
WEAR SAFETY GLASSES, SAFETY SHOES, AND GLOVES.
HAVE AREA AROUND INSTALLATION SITE CLEARED OF DEBRIS.
LOCKOUT POWER TO CONVEYOR(S) UNTIL START-UP.
LOOK OUT FOR SHARP EDGES WHILE HANDLING CONVEYOR COMPONENTS.
BE CAREFUL IN AND AROUND THE CONVEYOR(S) DURING INSTALLATION.
ALSO, BE AWARE OF OTHERS IN THE AREA.
ONLY ALLOW QUALIFIED PERSONNEL TO ASSEMBLE AND INSTALL CONVEYORS.
FRAME ASSEMBLY
If the frame and belt have been shipped "knocked down" use the following information to aid in assembly.
1.
If the conveyor is not to be put into use immediately, oil the belt liberally and store along with the frame in a
dry location.
2.
Layout a line on the floor to represent the centerline of the conveyor. As frame sections are bolted together make
sure they remain centered on the line.
3.
Bolt together conveyor frames finger tight with the fasteners provided. Make sure that the tracks, which the belt
rides on, are lined up and level to ensure a smooth transition from one section to the next.
(Weld tracks and grind smooth for best results.)
NOTE: If several sections of frame are to be joined in a particular sequence, they will be factory
matched marked. See FIGURE 1.
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
Go to Table of Contents
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
4
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
C O
N
V E Y O R S
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
drive.
7/21
TM
TM
TM
C O
N
V E Y O R S
C O
N
V E Y O R S
Advertisement
Table of Contents
