Related Manuals for Tesup ATLAS2.0
Summary of Contents for Tesup ATLAS2.0
- Page 1 ATLAS2.0 (MADE IN EUROPE) ATLAS2.0 Vertical turbine “WIND POWER NOW AT YOUR DOORSTEP.” Revision Index 00 USER MANUAL Revision Date: Made in Europe TESUP...
- Page 2 ATLAS 2.0 (MADE IN EUROPE) A GLIMPSE OF ATLAS 2.0 ~ 2 ~ TESUP...
- Page 3 Shipping Conditions Prerequisites at the place of use 7.2.1 Permissible wind class, footprint, and minimum clearances 7.2.2 Mounting Details Unpacking the components Assembling the wind turbine Electrical Connections Regular Operation Switching on the wind turbine system ~ 3 ~ TESUP...
- Page 4 Maintenance and cleaning by the user Removal from service and disposal 11.1 Final decommissioning of the wind turbine system 11.2 Disposal of the wind turbine system and components Declaration of Conformity Appendix Manufacturer Details & Customer Support Notes ~ 4 ~ TESUP...
- Page 5 The wind turbine system has been erected correctly by a suitably trained person. o All operating personnel have read and fully understood this translation of the original instructions o The wind turbine system is properly maintained and repaired. ~ 5 ~ TESUP...
-
Page 6: Symbols Used
DANGER: Immediate danger can cause serious injury. WARNING: Potential Danger can cause Serious injury. CAUTION: Potential Danger can cause moderate injury. NOTE: Useful Tips ▪ OTHER SIGNS USED: GENERAL WARNING. HIGH VOLTAGE MAY START WITHOUT WARNING. ENVIORNMENTAL HAZARD SAFETY SYMBOLS ~ 6 ~ TESUP... -
Page 7: Warranty Details
▪ Please notify the manufacturer or his authorised representative about any of the following: o Accidents o Potential safety hazards associated with the wind turbine system o Ambiguities in this translation of the original instructions o Description of the wind turbine system ~ 7 ~ TESUP... -
Page 8: Technical Description
All modifications or changes to the wind turbine system without the manufacturer’s written approval! o Use of parts other than ATLAS 2.0 original parts. o Operation in non-approved SWTS classes. o Operation in strong winds or hurricanes. ~ 8 ~ TESUP... -
Page 9: System Components
ATLAS 2.0 (MADE IN EUROPE) 3.3 SYSTEM COMPONENTS: NOTE: Several Batteries can be connected in Parallel Or series depending upon the system voltage. CHARGE CONTROLLER BATTERY ATLAS2.0 WIND TURBINE INVERTER ~ 9 ~ TESUP... - Page 10 ATLAS 2.0 (MADE IN EUROPE) 3.4 WIND TURBINE COMPONENTS: Item No. Description Quantity Turbine Blades Bottom Flange Mounting Base Wing Support Mounting Shaft Top Flange PART LIST TABLE ~ 10 ~ TESUP...
-
Page 11: Parameter Details
DIRECTION OF ROTATION Clockwise STARTING WIND SPEED 2 m/s NO. OF BLADES MAX RPM MAX SPEED 50 m/s NOISE 30 dB PARAMETER WARNING: If a hurricane scale III (50–58 m/s) or above occurs, please cover wind turbine blades ~ 11 ~ TESUP... -
Page 12: Power Curve
ATLAS 2.0 (MADE IN EUROPE) 4.1.1 POWER CURVE: POWER CURVE ~ 12 ~ TESUP... -
Page 13: General Arrangement Drawing
ATLAS 2.0 (MADE IN EUROPE) 4.2 GENERAL ARRANGEMENT DRAWING: DIMENSIONS IN mm [inches] ~ 13 ~ TESUP... -
Page 14: Technical Details
ATLAS 2.0 (MADE IN EUROPE) 5. CONTROLLER 5.1 TECHNICAL DETAILS: ▪ The Wind Turbine Charge Controller from TESUP is an intelligent controller which controls the wind turbine. It safely and efficiently charges and control your battery with the wind generator combination. -
Page 15: Wiring Diagram
ATLAS 2.0 (MADE IN EUROPE) 5.2 WIRING DIAGRAM: WIRING DIAGRAM ~ 15 ~ TESUP... -
Page 16: Storage & Operation
5.2 STORAGE & OPERATION: ▪ STORAGE: o Ambient temperature: -15 to +40°C. o Storage location: Dry, frost-free. ▪ OPERATION: o Ambient temperature: -25 to +40°C. o Place of use: Max. SWTS Class III acc. to EN 61400-2. ~ 16 ~ TESUP... -
Page 17: Safety Information
Properly complete the Warranty Registration Card Observe wire size and fuse recommendations listed in the Wiring Section of this manual. ▪ WARNING: Rotating blades are a serious mechanical hazard. Install wind turbines so no one can come in contact with blades. ~ 17 ~ TESUP... -
Page 18: Shipping Conditions
NOTE: When choosing the place of use, make sure adequate room is available to tilt the tower and blades if necessary. ~ 18 ~ TESUP... - Page 19 ATLAS 2.0 (MADE IN EUROPE) 7.2.2 Mounting Details: NOTE: Use of M10 hex bolts or Anchor Fasteners recommended. MOUNTING DETAILS ~ 19 ~ TESUP...
-
Page 20: Unpacking The Components
First we take thick thin and long lamas and mount the thin ones to the outside of the blade (in the direction of TESUP), the thick ones to the inside of the blade with the corresponding hole centres. We apply this mounting on three blades too. - Page 21 ATLAS 2.0 (MADE IN EUROPE) TURBINE BODY BOTTOM FLANGE FLANGE SHAFT WING ASSEMBLY BOTTOM LAMAS LAMAS TURBINE ASSEMBLY WING ATLAS ASSEMBLY ASSEMBLY PROCEDURE ~ 21 ~ TESUP...
-
Page 22: Electrical Connections
WARNING: All work on electrical equipment must be carried out by a qualified electrician with the power switched off! NOTE: To ensure proper operation, you must use an original TESUP charge controller ▪ Wind Turbine has 3 phase AC (Shown in RED) connection. -
Page 23: Regular Operation
8.1 SWITCHING ON THE WIND TURBINE SYSTEM: ▪ Unlock the emergency stop button or release the brake button on the TESUP charge controller. ▪ The brake is released. ▪ The fast-blinking red LED on the TESUP charge controller goes out. -
Page 24: Emergency Shutdown
9. SHUTTING DOWN THE WIND TURBINE 9.1 EMERGENCY SHUTDOWN: ▪ Switch on the brake. ▪ The wind turbine is short-circuited via the TESUP charge controller. 9.2 TEMPORARY SHUTDOWN: ▪ Switch on the brake. ▪ The wind turbine is short-circuited via the TESUP charge controller. -
Page 25: Safety Precautions During Maintenance Work
Inspect the cables for damage wiring WARNING: Shut down the wind turbine system immediately if the rotor blades or the electrical wiring are damaged. INSPECTION SCHEDULE TABLE ▪ Refer to the supplementary documents for information on maintaining supplier components. ~ 25 ~ TESUP... -
Page 26: Maintenance And Cleaning By The User
▪ Coat the wind turbine and the rotor blades regularly with commercially available underbody protection wax using a soft cloth. NOTE: A wax film protects the surfaces of the wind turbine and the rotor blades from the weather and increases the efficiency of the blades. ~ 26 ~ TESUP... -
Page 27: Removal From Service And Disposal
COMPONENTS: ▪ Where necessary, dispose of the individual components in consultation with the responsible local authorities. Wind turbine system Wiring, electrical components Dispose of as electronic scrap Mechanical components Segregate prior to disposal DISPOSAL DETAIL TABLE ~ 27 ~ TESUP... - Page 28 ATLAS 2.0 (MADE IN EUROPE) 12. DECLARATION ~ 28 ~ TESUP...
- Page 29 PAGE 15: WIRING DIAGRAM PAGE 17: PERSONNEL REQUIREMENT TABLE PAGE 19: MOUNTING DETAILS PAGE 21: ASSEMBLY PROCEDURE PAGE 22: CABLE DETAILS PAGE 25: INSPECTION SCHEDULE TABLE PAGE 27: DISPOSAL DETAIL TABLE 14. MANUFACTURER DETAILS & CUSTOMER SUPPORT ~ 29 ~ TESUP...
- Page 30 ATLAS 2.0 (MADE IN EUROPE) TESUP HEADQUATERS, 22 SUTTON LANE NORTH CHISWICK, LONDON W4 4LD UNITED KINGDOM TESUP OFFICIAL WEB-STORE ONLINE CHAT ~ 30 ~ TESUP...
- Page 31 ATLAS 2.0 (MADE IN EUROPE) 15. NOTES ~ 31 ~ TESUP...
Need help?
Do you have a question about the ATLAS2.0 and is the answer not in the manual?
Questions and answers