Table of Contents
Advertisement
EN 22
5.
TPM9.5A LA
Main Menu
Sub-menu 1
Download from USB Copy Channel List from USB
Copy NVM from USB
Copy Readable Info from USB
Copy EDID from USB
Initialize NVM
Press [OK] to Initialize NVM
immediately
EDID Write Enable
Press [OK] to enable EDID writable
immediately
Service Data
Type Number
Production Number
12NC SSB
12NC PSU
12NC Display
Clear OAD Version
Press [OK] to clean OAD Version
immediately
How to Navigate
•
In the SAM menu, select menu items with the UP/DOWN
keys on the remote control transmitter. The selected item
will be indicated. When not all menu items fit on the screen,
use the UP/DOWN keys to display the next/previous menu
items.
•
With the "LEFT/RIGHT" keys, it is possible to:
–
(De) activate the selected menu item.
–
(De) activate the selected sub menu.
–
Change the value of the selected menu item.
•
When you press the MENU button once while in top level
SAM, the set will switch to the normal user menu (with the
SAM mode still active in the background).
•
Press the following key sequence on the remote control
transmitter: "062596" directly followed by the "Home"
button to switch to SDM (do not allow the display to time out
between entries while keying the sequence).
How to Store SAM Settings
To store the settings changed in SAM mode (except the
RGB Align settings), leave the top level SAM menu by using
the POWER button on the remote control transmitter or the
television set. The mentioned exceptions must be stored
separately via the STORE button.
How to Exit SAM
Use one of the following methods:
•
Switch the set to STANDBY by pressing the mains button
on the remote control transmitter or the television set.
•
Via a standard RC-transmitter, key in "00" sequence.
Table 5-2 Factory mode overview
Item Item value
0
F/W VERSION
1
Panel_ID
2
ERR Code: xxx xxx xxx xxx xxx 000 000 000 000 000
3
CLEAR ERROR BUFFER
4
NVM ADDRESS
5
NVM VALUE
6
NVM STORE
7
NVM COPY TV to USB
8
NVM COPY USB to TV
2012-Nov-30
Service Modes, Error Codes, and Fault Finding
Sub-menu 2
Press [OK] use key pad edit type
number immediately
Press [OK] use key pad edit
production number immediately
Press [OK] use key pad edit SSB
immediately
Press [OK] use key pad edit PSU
immediately
Press [OK] use key pad edit display
immediately
Default value
32"
42"
46"
47"
Description
Press OK
Displays the software versions of the supplier, Flash PQ, Smart Picture, BL Dimming, Source Meter, the
Picture Quality checksum, the Dimming library, the Source meter library, the Flash AQ, the MTK, MCU and
OAD software versions.
See table
6-3 Display code
Displays and changes the Panel ID with the left and right cursor; be careful changing this, it can result in not
overview
correct displaying the screen!
Values showing the last 5 errors during the last 50 hours of operation, according to table
Press OK
Selecting this clear all current error codes.
0
NVM address 0 to 8191, Use Item 6 to change and 7 to store the data to the correct NVM address
various
Displays the value at the NVM address of item 5
Press OK
Use this option to save the data of item 6 to NVM address of item 5
Press OK
Use this to store the NVM data to the REPAIR folder of a FAT formatted USB memory stick. The TV will write
two files in the REPAIR folder of the memory stick. It will create this folder if it does not exist. The items are
"Channel list", "Personal settings", "Option codes", "Display-related alignments" and "History list". In case the
download to the USB stick was not successful "Failure" will appear. In this case, check if the USB stick is
connected properly. Now the settings are stored onto the USB stick and can be used to download onto another
TV or other SSB. Uploading is of course only possible if the software is running and if a picture is available.
This method is created to be able to save the customer's TV settings and to store them into another SSB.
Press OK
Use this to store the NVM data from the USB memory stick to the TV. The TV will save the two files which were
created in item 8 to the NVM of the set. Use these options when replacing a SSB. When "USB to TV Success"
is displayed remove the power and restart the TV
Description
To download several settings from the USB stick to the TV
To initialize a (corrupted) NVM. Be careful, this will erase all settings.
Enable EDID for writing
Edit and display the applicable service data by using the displayed key pad.
Clean OAD (Over Air Download, firmware update method) Version
Note: When the TV is switched "off" by a power interrupt while
in SAM, the TV will show up in "normal operation mode" as
soon as the power is supplied again. The error buffer will not be
cleared.
5.2.4
Contents of the Factory mode:
Purpose
•
To perform extended alignments.
Specifications
•
Displaying and or changing Panel ID information.
•
Displaying and or changing Tuner ID information.
•
Error buffer clearing.
•
Various software alignment settings.
•
Testpattern displaying.
•
Public Broadcasting Service password Reset.
•
etc.
How to Activate the Factory mode
To activate the Factory mode, use the following method:
•
Press the following key sequence on the remote control
transmitter: from the "Home screen" press "1999", directly
followed by the "Back" button. Do not allow the display to
time out between entries while keying the sequence.
After entering the Factory mode, the following items are
displayed,
back to
div. table
5-4 Error code table
Hide quick links:
Advertisement
Table of Contents
