Related Manuals for Flint & Walling FJ05S
Summary of Contents for Flint & Walling FJ05S
- Page 1 SHALLOW WELL JET PUMP MODEL FJ05S 1/2 HP flintandwalling.com ATTACH YOUR RECEIPT HERE Serial Number Purchase Date FW1642 C Copyright © 2018 Flint & Walling. All rights reserved.
-
Page 2: Table Of Contents
MINUTE AT DISCHARGE 20 PSI MODEL VOLTAGE HZ 5 FT. 15 FT. 25 FT. FJ05S 115/230 7.8/3.6 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. Copyright © 2018 Flint & Walling. All rights reserved. - Page 3 SAFETY INFORMATION DANGER ELECTRICAL SHOCK HAZARD. Always disconnect power source before performing any work on or near the motor or its connected load. If the power disconnect point is out-of-sight, lock it in the open position and tag it to prevent unexpected application of power. Failure to do so could result in fatal electrical shock.
-
Page 4: Package Contents
SAFETY INFORMATION CAUTION PRODUCT DAMAGE MAY RESULT This pump is not to be used for irrigation or water systems. PRODUCT DAMAGE MAY RESULT Protect the power cable from coming in contact with sharp objects. PRODUCT DAMAGE MAY RESULT Do not run pump dry. PRODUCT DAMAGE MAY RESULT Pump and plumbing must be full of water before startup. -
Page 5: General Pump Information
GENERAL PUMP INFORMATION Typical Pump Setup 3/4 or 1 in. Discharge Pipe 1. Shallow well jet pumps are designed for use Discharge to Home where the suction lift is 25 ft. or less. They Suction can be used with drilled or cased wells. Lift 1-1/4 in. -
Page 6: Well To Pump Connection
GENERAL PUMP INFORMATION Pipe And Fittings 3. Use galvanized steel or NSF PW Schedule 1 in. NPT 40 PVC pipe and fittings. This material is Discharge 1-1/4 in. designed for water pressure and will seal Suction against air and water under pressure. Do not use DWV fittings, as these are designed for drains without pressure and will not seal properly. - Page 7 WELL TO PUMP CONNECTION (SUCTION PIPE) 2. Using a 2-step PVC system (not included), attach enough 1-1/4 in. PVC pipe and 1-1/4 in. PVC pipe couplings (not included) to the adapter to equal the depth of the well, minus 5 ft. 3.
- Page 8 WELL TO PUMP CONNECTION (SUCTION PIPE) 6. Wrap thread tape (not included) around the threads of a 1-1/4 in. male PVC adapter (not included). Thread the adapter into the 1-1/4 in. 1-1/4 in. Male opening in the front of pump. PVC adapter 7.
-
Page 9: Pump To Tank Connection
PUMP TO TANK CONNECTION (DISCHARGE PIPE) 1. Wrap thread tape around threads of a 1 in. discharge tee (not included). Using a pipe 1 in. Discharge Tee wrench, thread the 1 in. discharge tee into the 1 in. opening in the top of pump. 2. -
Page 10: Tank To House Connection
TANK TO HOUSE CONNECTION 1. Most pressure tanks will have a 1 in. inlet elbow on the bottom. Connect to this elbow with a 1 in. MPT x 1 in. slip (glue) adapter and short piece of pipe. Adapter IL1365 Glue Pipe 2. -
Page 11: Pump Electrical Connections
TANK TO HOUSE CONNECTION 5. Attach the pipe from the pump to the tee installed in Step 4. Then, from the tee, Shut off valve install 3/4 in. pipe and optional shut off Glue valve (not included) to connect tee to house plumbing. - Page 12 PUMP ELECTRICAL CONNECTIONS Wiring the pressure switch CAUTION: Make certain that the power source matches the pump requirements. This pump has a dual voltage motor and can run on either 115 V or 230 V. Pump is pre-set at the factory to run on 230 V. 1.
-
Page 13: Pump Priming And Startup
PUMP ELECTRICAL CONNECTIONS 5. Connect the green ground wire from the Ground Screws power supply to the remaining green ground screw in the pressure switch and re-attach the pressure switch cover. Wire Wire from from power motor supply Green ground wire PUMP PRIMING AND STARTUP PRIMING... - Page 14 PUMP PRIMING AND STARTUP 4. Check to be sure water in the cavity of pump Water Level stays constant. If water level goes down, it could indicate a leak in the foot valve, check valve or suction pipe. Suction pipe Check for leaks 5.
-
Page 15: Care And Maintenance
CARE AND MAINTENANCE Winterizing Vent Plug CAUTION: Drain the entire system if there is danger of freezing. 1. To drain pump, remove the drain plug located on the front of pump and the vent plug located on the top of pump. Drain Plug WARRANTY... -
Page 16: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Little or no 1. Pump is not primed 1. Follow priming instructions (page 13) discharge 2. Suction lift too high or too long 2. Move pump closer to water source. Lift should be less than 25 ft. 3. -
Page 17: Replacement Parts
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-800-742-5044, 7:30 a.m. - 5 p.m., EST, Monday - Friday. PART DESCRIPTION PART NO. O-rings / Nozzle / Venturi Kit 023735 Diffuser 023707 Impeller 023709 Mechanical Seal 023720 O-Ring 023721 Pressure Switch...