Table of Contents
Advertisement
3.2 Voice Assistance
Voice Assistance can be activated by long pressing the right
earbud for 1 second.
3.3 Ambient Pass-Through
PI7 features ambient pass-through which lets some external noise
from the surrounding environment, such as safety
announcements or conversations, to be heard without taking the
headphones off.
Ambient pass-through can ONLY be enabled/disabled through
Bowers & Wilkins headphone App. The level of ambient pass-
through can be further customised to suite your needs through
the App.
3.4 Wear Sensors
PI7 incorporate our latest enhanced wear detection sensors in
both earbuds, enabling sensors intelligent battery conservation by
entering standby when removed from the ears. When worn again,
PI7 automatically wakes and connects to the last connected
Bluetooth device.
During media playback, PI7 will auto pause when either earbud is
placed from the ear. Playback will auto resume when the earbud
is placed back on the ear. Auto resume has been further
optimized so it is ready only when you are.
Wear sensor can ONLY be turned ON/Off using the Bowers &
Wilkins Headphone App.
Note: Take special care when wearing your earphones,
hair or accessories trapped between your ears and the ear
buds may interfere with proximity sensing.
4. . Stowing the Ear Buds
When not being worn in the ear, the PI7 ear buds can be stored
and charged inside the charge case. The ear buds will be
magnetically held in the charge case. The ear buds can only be
stowed in one orientation.
Note: Take special care when wearing your earphones, hair
or accessories trapped between your ears and the ear
buds may interfere with proximity sensing.
5. Battery Charging
Your Bowers & Wilkins PI7 ships with the battery partially charged
& may be used immediately. For best practice we recommend to
fully charge the earphones before first use. Please allow up to 3
hours for full charge. The earphones can be used while charging.
To charge the PI7 ear buds:
1. Place the PI7 ear buds int the charge case.
2. Close the charge case lid.
To charge the PI7 charge case with cable:
1. Please use the supplied USB charging cable and connect the
USB plug to a USB wall charger or a powered computer USB
socket.
2. Then connect the USB-C end to the charge case USB-C
socket.
Note: During charging, the charge case indicator will blink
green. When fully charged, the indicator will remain
illuminated. The charge case can be charged with or without
the ear buds being housed inside the charge case.
To charge the PI7 charge case with a wireless charging station:
1. Place the carging case onto a wireless charging station
2. Ensure that the rear of the charging case is on the charging
station (with the case indicator facing up)
Note: During charging, the charge case indicator will blink
green. When fully charged, the indicator will remain
illuminated.
5.1 Status Indicator
The status indicator is located on the charge case providing information on the
ear buds when they are located in the case and provide information on the
charging case when the ear buds are removed.
With the Ear buds in the charging case-Please see Diagram 3.
With the Ear buds in the charging case
Illumination
Operational state
Green (case lid open)
Ear bud battery charge > 40%
Yellow (after power on)
Ear bud battery charge >20%, <40%
Red (after power on)
Ear bud battery charge <20%
Red (blinking)
Ear bud factory Reset
Red (Solid)
Hardware Reset/ System Crash
Blue blinking
Pairing Mode Enabled
Blue (3 sec solid)
Pairing successful
Diagram 3
Status indicator illuminations
With the earbuds removed from the charging case
Illumination
Operational state
Green (case lid open)
Ear bud battery charge > 40%
Yellow (after power on)
Ear bud battery charge >20%, <40%
Red (after power on)
Ear bud battery charge <20%
Red (blinking)
Factory Reset
Red (Solid)
Hardware Reset/ System Crash
Diagram 3
Status indicator illuminations
4
Advertisement
Table of Contents
