Bunn DUAL TF DBC W/SMART FUNNEL DUAL068000 Programming Manual
Bunn coffeemaker user manual
Hide thumbs
Also See for DUAL TF DBC W/SMART FUNNEL DUAL068000:
- Installation and operating manual (7 pages) ,
- Installation & operating manual (54 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bunn DUAL TF DBC W/SMART FUNNEL DUAL068000
Summary of Contents for Bunn DUAL TF DBC W/SMART FUNNEL DUAL068000
- Page 1 DUAL TF DBC ® ® W/SMART FUNNEL ® S/N DUAL068000 & UP SINGLE TF DBC ® ® W/SMART FUNNEL ® S/N SNG0033000 & UP PROGRAMMING MANUAL BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644...
- Page 2 AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.
-
Page 3: Table Of Contents
The brewer incorporates a wireless interface system that allows the DBC Grinder to load certain information into the "programming chip" located inside the handle of the funnel. This information includes what flavor of coffee is being ground and what batch size will be brewed (small, medium, or large). Once the correct flavor name and amount of coffee is ground, the funnel is loaded into the brewer. -
Page 4: Glossary
AD CARD: An assembly consisting of computer chips and an instruction label. Used for loading advertising messages into the brewer. BREW LOCKOUT: The inability to initiate a brew if the water temperature is less than the ready temperature programmed into the brewer. BYPASS: The process of diverting a portion of the brew water to the outside of the paper filter so that it does not pass through the coffee grounds. -
Page 5: Programming
This is used to access the programming mode and is also used to scroll forward through the function list. 2. Upper left corner of the "B" in the BUNN logo This is used to scroll backwards through the function list. -
Page 6: Programming The Brewer
The programming of the brewer is divided into two levels. There is one function in Level 1. All other functions are accessed in Level 2. The following function screens are in order of appearance. Each screen will have instructions on how to access, and the procedures to program the various functions of the brewer. -
Page 7: Program Functions (Flow)
FOR SINGLE BREWERS, NO NAME LEFT AND NO NAME RIGHT BREW SETTINGS FOR DUAL BREWERS Page 7 GO TO SET NEW RECIPE, AND FOLLOW THE INSTRUCTIONS REFER TO NAME LIST IN GRINDER MANUAL CONTACT BUNN-O-MATIC FOR ASSISTANCE P2369-1 41342 080108... - Page 8 PROGRAMMING THE BREWER (cont.) PROGRAM FLOW DIAGRAM Press upper right hidden switch for approximately 2 seconds, until the following screen appears. Press upper right hidden switch for approximately 4 seconds, until “UNITS” appears on screen. Sets unit of Sets unit of UNITS measure to measure to...
- Page 9 PROGRAMMING THE BREWER (cont.) PROGRAM FLOW DIAGRAM (Cont.) BYPASS DONE 3 BATCHES DONE? SET PULSE BREW DRIP TIME X.XX DONE 3 BATCHES DONE? SINGLE BREWERS DUAL NO-NAME BREWERS SETUP COMPLETE Return to (A) NO-NAME RIGHT NO-NAME LEFT SETUP COMPLETE SETUP COMPLETE Continue to (B) Return to (A) SET ALL...
- Page 10 PROGRAMMING THE BREWER (cont.) PROGRAM FLOW DIAGRAM (Cont.) L BYPS OZ/M XX.X DONE R BYPS OZ/M XX.X DONE CALIBRATE FLOW? BREW COUNTERS? SINGLE BREWERS DUAL BREWERS FUNNEL DETECT? DONE SERVICE TOOLS? SEL BREWER TYPE? ThermoF SoftHeat DONE FACTORY DEFAULTS FINISHED, returns to main screen CONTAINER RDY? QUIT...
- Page 11 PROGRAMMING THE BREWER (cont.) UNITS (SETTING UNITS OF MEASURE) This function allows the units of measure to be set in English or Metric readings for all screens. The program is defaulted to English. WARNING: Changing the unit of measure will erase all coffee recipes stored in memory.
-
Page 12: Enable Energy Saver
PROGRAMMING THE BREWER (cont.) ENABLE ENERGYSAVR This function allows the operator to enable the ENERGY SAVINGS mode function and set the idle time. Once the set idle time has expired, the operator can choose to have the heaters either turn off, or reduce the tank holding temp to 140°... -
Page 13: Set New Recipe (Using A Smart Funnel And G92T Dbc Or Mhg Grinder)
PROGRAMMING THE BREWER (cont.) SET NEW RECIPE Using a Smart Funnel and a G9-2T DBC or MHG Grinder: This function allows operator to set BREW VOL- UMES, BYPASS PERCENTAGES, PULSE BREW TIMES and DRIP-OUT TIMES for each coffee name preset in the grinder's memory. - Page 14 PROGRAMMING THE BREWER (cont.) SET NEW RECIPE (cont.) 8. Using (-) and (+), set the amount of brew water, in ounces, to be dispensed for that particular batch size. 9. When finished, press another batch size and re- peat step 8 for that size. Continue setting all batch sizes.
-
Page 15: Set New Recipe (Using A Recipe Card)
PERCENTAGES, PULSE BREW TIMES and DRIP-OUT TIMES for that particular coffee NAME. These can all be loaded in seconds. Contact Bunn-O-Matic Corporation for the avail- ability of RECIPE CARDS. NOTE: Instructions to program the brewer and grinder are printed on the RECIPE CARD, along with the coffee name that is being programmed. -
Page 16: Set New Recipe (No Smart Funnel Nor G9-2T Dbc Grinder)
This includes BREW VOLUMES, BYPASS PERCENTAGES, PULSE BREW TIMES, and DRIP-OUT TIMES. The brewer will perform in the same capacity as a standard Bunn Single/Dual Brewer. The instructions for programming the NO NAME settings are on the following pages. The same steps are followed for setting the recipe as those that are used to MODIFY A RECIPE, beginning on page 21. -
Page 17: Review Recipes/Modify Recipes/Set Up No Name Coffee
PROGRAMMING THE BREWER (cont.) REVIEW RECIPES/MODIFY RECIPES/SET UP NO NAME COFFEE FAVORS: This function has three parts. It allows the operator to view the brew settings for the various coffee names programmed into the brewer. It also allows the operator to modify (change) any of the BREW VOLUMES, BYPASS PERCENTAGES, PULSE BREW TIMES, and DRIP-OUT TIMES for a particular coffee name programmed into the brewer. - Page 18 PROGRAMMING THE BREWER (cont.) BREW OZ (SETTING OR ADJUSTING BREW VOL- UMES) This function allows adjustment of the brew vol- umes for each batch. The indicator signifies volume in ounces per batch. Procedure for modifying recipes - brew ounces: Range: 10.0 oz to 400 oz for all three batch sizes 1.
- Page 19 PROGRAMMING THE BREWER (cont.) % BYPASS This function allows adjustment of the amount of water that bypasses the grounds. The number signi- fies the percentage of the brew volume which does not flow over the coffee grounds. Modifying recipes - bypass percentages: Range: 0% to 90% for all three batch sizes NOTE: If the brewer is already in the % BYPASS screen, it is not necessary to follow steps 1 through 6 in this...
-
Page 20: Set Pulse Brew
PROGRAMMING THE BREWER (cont.) SET PULSE BREW: This function allows the operator to program the brewer to "pulse” the sprayhead flow on and off during a brew cycle (start and stop the flow of water out of the sprayhead). This feature allows the ability to “fine-tune”... -
Page 21: Manual Method
PROGRAMMING THE BREWER (cont.) SET PULSE BREW (cont.) EXIT TO NEXT FUNCTION SCREEN MODIFY SHOW NEXT SCREEN DISPLAYED BREW OZ: XX.XX 3 BATCHES DONE? % BYPASS XX.X 3 BATCHES DONE? SET PULSE BREW? SELECT METHOD EASY NEXT MANUAL EASY SEE SET PULSE BREW (EASY METHOD) REVIEW RECIPES? SINGLE... - Page 22 PROGRAMMING THE BREWER (cont.) SET PULSE BREW - EASY METHOD NOTE: The procedure to enter the PULSE BREW function must be performed prior to following the steps listed below. 1. The display should read BREW TIME: X.XX and a batch size indicator will be flashing. 2.
- Page 23 PROGRAMMING THE BREWER (cont.) SET PULSE BREW - MANUAL METHOD NOTE: The procedure to enter the PULSE BREW function must be performed prior to following the steps listed below. 1. The display should read 1st ON TIME X:XX and a batch size indicator will be flashing.
- Page 24 PROGRAMMING THE BREWER (cont.) DRIP TIME (now displayed on "non" funnel lock units as well) This function allows the setting or modification of the funnel locks to stay engaged after the end of a brew cycle. This ensures the funnel cannot be removed until after the liquid has emptied out of the funnel.
-
Page 25: Assign Recipes
PROGRAMMING THE BREWER (cont.) ASSIGN RECIPES This function allows for assigning a coffee name other than NO-NAME to the BREW switch. Procedure to assign recipes: 1. Press and hold the upper right hidden switch until the display reads UNITS. Release the switch. Press and release switch until the display reads ASSIGN RECIPE ?. -
Page 26: Enable Ads
PROGRAMMING THE BREWER (cont.) COPY SETTINGS (NO NAME COFFEE SETTINGS ONLY) (cont.) 2. Press YES in this screen. The display should read LEFT ->->-> RIGHT. 3. If the initial programming was done on the left side of the brewer, press YES. The display will read ARE YOU SURE? 4. -
Page 27: Set Ready (Ready Temperature)
PROGRAMMING THE BREWER (cont.) SET TEMP (cont.) 2. To adjust the brew temperature, press (-) to de- crease or (+) to increase the brew temperature. 3. When finished, press and release DONE to save the new setting, exit the SET TEMP function and advance to the next function screen, SET READY. - Page 28 PROGRAMMING THE BREWER (cont.) SPRAY OZ/M (SINGLE BREWERS) This function allows the operator to view or to enter the actual flow rate coming out of the sprayhead. This is NOT used to change the actual flow rate, but to tell the internal controller how fast the water is flowing.
- Page 29 PROGRAMMING THE BREWER (cont.) BYPASS OZ/M (SINGLE BREWERS) This function allows the operator to view or to enter the actual flow rate coming out of the bypass nozzle. This is NOT used to change the actual flow rate, but to tell the internal controller how fast the water is flowing.
-
Page 30: Calibrate Flow
PROGRAMMING THE BREWER (cont.) CALIBRATE FLOW This function allows the operator to enter the actual flow rate of the sprayhead and the bypass (for each side on DUAL brewers) by dispensing both separately for one minute. The volumes are then entered in ounces per minute (OZ/M). -
Page 31: Calibrate Sprayhead Flow
PROGRAMMING THE BREWER (cont.) CALIBRATE FLOW (cont.) Procedures to calibrate the bypass flow rate: 1. Place a container, accurately graduated in ounces, and with a minimum capacity of 60 ounces, below the funnel on the brewer to be calibrated. 2. Press and hold the upper right hidden switch until the display reads UNITS. -
Page 32: Brew Counters (View/Reset)
PROGRAMMING THE BREWER (cont.) BREW COUNTERS This function allows the operator to track the number of brew cycles completed. The number of brew cycles on the left side, the right side, and the total of both combined can be tracked on DUAL brewers. There is one resettable counter, and one life counter that is not resettable for SINGLE brewers and three resettable counters, and one life counter that is not... -
Page 33: Funnel Detect
PROGRAMMING THE BREWER (cont.) FUNNEL DETECT (optional) This function allows the operator to prevent the start of a brew cycle if a Smart Funnel is not positioned correctly in the funnel rails. FUNNEL DETECT ? DONE Procedure to set funnel detect: 1. - Page 34 PROGRAMMING THE BREWER (cont.) SERVICE TOOLS (cont.) NOTE: To bypass testing any component, press NEXT to advance to the next one, without testing the previ- ous component. 10. To test LEFT BYPASS, press ON. If the bypass valve is functional, water should run from the left brew bypass.
-
Page 35: Test Outputs (Components)
PROGRAMMING THE BREWER (cont.) SERVICE TOOLS (cont.) TEST SWITCHES? NOTHING PRESSED TEST FREQUENCY? BREWERS EXIT TO NEXT FUNCTION SCREEN EXIT TO NEXT FUNCTION SCREEN PRESS AND RELEASE ® SYMBO L FUNNEL LOCK SINGLE BREWERS 125.0 KHZ. 4 DUAL REFILL VALVE <-<-<- 125.0 KHZ. -
Page 36: Factory Defaults (Reset)
PROGRAMMING THE BREWER (cont.) SERVICE TOOLS (cont.) the next function screen. Press YES to run tests on various components and outputs within the brewer. 5. The display should read TEST OUTPUTS?. 6. In TEST OUTPUTS screen, press NO. Continue to press and release NO until the display reads TEST FREQUENCY?.