Makita HM002G Instruction Manual page 13

Lighting up the front lamp
► Fig.5: 1. Lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Electronic function
The tool is equipped with the electronic functions for
easy operation.
• Constant speed control
The speed control function provides the constant
rotation speed regardless of load conditions.
• Soft start
The soft-start function minimizes start-up shock,
and makes the machine start smoothly.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Side handle (auxiliary handle)
CAUTION:
Always use the side handle to
ensure safe operation.
CAUTION:
After installing or adjusting the
side handle, make sure that the side handle is
firmly secured.
The side handle can be swung in a vertical direction
and secured at any desired position. It can also be
adjusted at eight steps back and forth in a horizontal
direction. Loosen the clamp nut to swing the side han-
dle to a desired position, and then tighten the clamp nut
securely.
► Fig.6: 1. Side handle 2. Clamp nut
Installing or removing bit
Grease
Clean the shank end of the bit and apply grease before
installing the bit.
Coat the shank end of the bit beforehand with a small
amount of grease (about 0.5 - 1 g). This chuck lubrica-
tion assures smooth action and longer service life.
► Fig.7: 1. Shank end 2. Grease
Insert the bit into the tool. Turn the bit and push it in until
it engages.
If the bit cannot be pushed in, remove the bit. Pull the
release cover down a couple of times. Then insert the
bit again. Turn the bit and push it in until it engages.
After installing the bit, always make sure that the bit is
securely held in place by trying to pull it out.
► Fig.8: 1. Bit 2. Release cover
To remove the bit, pull the release cover down all the
way and pull the bit out.
► Fig.9: 1. Bit 2. Release cover
Bit angle
The bit can be secured at 12 different angles. To
change the bit angle, slide the change ring cover for-
ward, then turn the change ring cover to change the bit
angle. At the desired angle, slide the change ring cover
back to the original position. The bit will be secured in
place.
After changing the bit angle, make sure the angle is
fixed by trying to rotate the bit.
► Fig.10: 1. Change ring cover
Dust extractor attachment
Optional accessory
1. Install the hose holder (A).
Loosen the clamp nut, and then remove the hex bolt.
Install the hose holder (A) between the hex bolt and the
clamp nut by tightening the clamp nut firmly.
► Fig.11: 1. Hex bolt 2. Hose holder (A) 3. Clamp nut
2. Attach the holder joint to the tool, and then attach
the hose holder (C) to the holder joint.
► Fig.12: 1. Holder joint 2. Hose holder (C)
NOTE: The hose joint can be attached to either side
of the tool.
WARNING:
only for attaching the holder joint.
Using the mounting part for any other purpose may
cause an unexpected accident.
3.
Attach the dust cover and the hose to the tool, and
then fix the hose to the hose holders.
► Fig.13: 1. Dust cover 2. Hose 3. Hose holder (A)
4. Hose holder (C)
4. Connect the hose to the hose of the vacuum
cleaner with the hose joint.
NOTE: If the hose is not included, attach the dust
cover to the cleaner's joint or attach it to Makita's
hose ø28.
5.
Adjust the distance between the dust cover and
the tip of the chisel or bull point. The recommended
distance is 30 mm to 100 mm.
► Fig.14: (1) 30 mm to 100 mm
13 ENGLISH
Use the mounting part of the tool