Subscribe to Our Youtube Channel
Related Manuals for Shuttle MS52PN
Summary of Contents for Shuttle MS52PN
- Page 1 MS52PN Intel Pentium 4 478-pin Processor with 533/400 MHz FSB Based DDR MAINBOARD User's Manual...
- Page 2 The information contained in this manual is provided for general use by the customers. Trademarks Shuttle is a registered trademark of Shuttle Inc. nVIDIA is a registered trademark of nVIDIA Corporation. AMD, Athlon, and Duron are registered trademarks of AMD Corporation.
- Page 3 Statement of Shuttle Mainboard via the EMI Test Shuttle mainboards have been via the EMI test in terms of series of regulations: EN55022/ CISPR22/AS/NZS3548 Class B, EN55024 (1998/AS/NZS), EN4252.1 (1994), EN61000, ANSI C63.4 (1992), CFR47 Part 15 Subpart B, and CNS13438 (1997). The items tested are illus- trated as follows: (A) Voltage: AC 110V/60HZ &...
- Page 4 EMI Interference: Crystal: 32.768 KHz(Y3)/24.576 MHz(Y2)/25.000 MHz(Y4)/12.000 MHz(Y5)/ 14.318 MHz(Y1) Clock Generator: N/A (D) Supported Host Peripherals: Host Peripheral Product Name Model Name Case MS52PN Seventeam Power Supply ST-250HK IBM HDD (82.3GB) IC35L080AVVA07-0 Panasonic FDD JU-257A606P CODE CD-ROM DVD-116 (F) Notices for Assembling Computers: 1.
-
Page 5: Table Of Contents
TABLE OF CONTENTS WHAT'S IN THE MANUAL ..............4 Quick Reference ....................4 About This Manual ................... 4 1 INTRODUCTION ................5 1.1 TO DIFFERENT USERS ................5 FIRST-TIME DIY SYSTEM BUILDER............5 EXPERIENCED DIY USER ................. 5 SYSTEM INTEGRATOR................5 1.2 ITEM CHECKLIST: .................. - Page 6 Back Panel Connectors PS/2 Mouse & PS/2 Keyboard Port Connectors ........27 Parallel Port Connector ................27 COM1 Port Connector ................27 Game Port Connector ................27 VGA Port Connector .................. 27 Line_Out Port Connector ................28 Line_In Port Connector ................28 Microphone Port Connector ...............
- Page 7 4 SOFTWARE UTILITY ..............37 4.1 Mainboard CD Overview ................. 37 4.2 Install Mainboard Software ..............38 4.2.A Install SIS AGP Driver ................39 4.2.B Install SIS IDE Driver ................39 4.2.C Install SIS VGA Driver ................40 4.2.D Install SIS USB2.0 Driver ..............40 4.2.E Install Realtek LAN Driver ..............
-
Page 8: What's In The Manual
WHAT'S IN THE MANUAL Quick Reference Hardware Installation >> Step-by-Step ..........Page 10 Jumper Settings >> A Closer Look ............Page 22 Software Utility >> How to Install ............Page 40 BIOS Setup >> How to Configure ............Page 43 About This Manual For First-Time DIY System Builder ............ -
Page 9: Introduction
Experienced DIY User Congratulate on your purchase of the MS52PN mainboard. You will find in- stalling your new MS52PN mainboard is quite easy. Bundled with an array of onboard functions, the highly-integrated MS52PN mainboard provides you with a total solution to build the stablest and most reliable system. Referring to sec- tion 3.2 Jumper Settings and Chapter 4 Software Utility, you will find... -
Page 10: Item Checklist
1.2 Item Checklist: Check all items with your MS52PN mainboard to make sure nothing is missing. A complete package should include: - One Shuttle MS52PN Mainboard PSKBM1 CPU_FAN1 LPT1 ATX1 VGA1 AUDIO1 CDIN1 CDIN2 SIS'04 EPD0392 0413BA ATX2 962L SIS'02... -
Page 11: Features
2 FEATURES MS52PN mainboard is dedicatedly designed for demanding PC users who desire high performance and maximum intelligent features in a compact package. 2.1 Specifications - CPU Support Intel pentium4, 478-pin processors with 533/400 MHz FSB. Supports Hyper-Threading Technology and Prescott CPU. - Page 12 Ø 1 x PS/2 Mouse Ø 1 x PS/2 Keyboard Ø 1 x Serial port Ø 1 x Parallel port Ø 1 x VGA port Ø 1 x Game port Ø 2 x USB ports Ø 1 x LAN port Ø...
- Page 13 Board dimension: 244mm x 244mm. - Advanced Features Ø Low EMI - Built in spread spectrum. Unused PCI/SDRAM slots are shut off by the automatic clock for reducing EMI. Ø Dual Function Power Button - The system can be in any of the two states: one is Suspend mode and the other is Soft-Off mode.
-
Page 14: Hardware Installation
This section outlines how to install and configure your mainboard. Referring to the follow- ing mainboard layout helps you identify various jumpers, connectors, slots, and ports. 3.1 Step-by-Step Installation Accessories Of MS52PN Two DIMM Slots SiS 962L Chipset SiS 651C Chipset... -
Page 15: Step 1 Install The Cpu
Step 1 CPU Installation: This mainboard supports Intel Pentium 4 Socket 478 series CPU. Please follow the steps as follows to finish CPU installation. Note the CPU orientation when you plug it into CPU socket. 1. Pull up the CPU socket lever to 90-degree angle. CPU socket lever up to 90-degree angle 2. -
Page 16: Step 2 Set Jumpers
Step 2 Set Jumpers The default jumper settings have been set for the common usage standard of this mainboard. Therefore, you need not to reset the jumpers unless you re- quire special adjustments as the following case: Clear CMOS Setting BIOS Protection Setting For first-time DIY system builders, we recommend that you not change the default jumper settings if you are not quite familiar with the mainboard con-... -
Page 17: Step 4 Install Internal Peripherals In System Case
Step 4 Install Internal Peripherals in System Case Before you place the mainboard into your system case, we recommend that you first assemble all the internal peripheral devices into the computer hous- ing, including, but not limited to, the hard disk drive (IDE/HDD), floppy disk drive (FDD), CD-ROM drive, and ATX power supply unit. -
Page 18: Step 5 Mount The Mainboard On The Computer Chassis
Step 5 Mount the Mainboard on the Computer Chassis 1. You may find there are a lot of mounting holes on your computer chassis and mainboard. To match the holes on both properly, the key point is to make the back panel of the mainboard in a close fit with your system case, as shown below. -
Page 19: Step 6 Connect Front Panel Leds/Switches/Usbs/Audio
Step 6 Connect Front Panel LEDs/Switches/USBs/Audio You can find there are several cables existing in the system case and originat- ing from the front panel devices (HDD LED, ACPILED, Reset switch, Power switch, Audio and USB devices etc.). These cables serve to connect the front panel LEDs, switches, Audio and USB2/3 connectors, as shown below. -
Page 20: Step 7 Connect Ide And Floppy Disk Drives
Step 7 Connect IDE and Floppy Disk Drives 1. IDE cable connectors 2. Floppy cable connector FDD1 - 16 -... -
Page 21: Step 8 Connect Other Internal Peripherals
Step 8 Connect Other Internal Peripherals 1. IR header (IR1) 2. CD_IN connectors (CDIN1/CDIN2) CDIN1 CDIN2 3. Wake On Modem (WOM1); Wake On LAN (WOL1) WOM1 WOL1 - 17 -... -
Page 22: Step 9 Connect The Power Supplies
Step 9 Connect the Power Supplies 1. System power connectors (ATX1/ATX2) ATX1 Step 10 Install Add-On Cards in Expansion Slots 1. Accelerated Grapics Port (AGP) Card 2. PCI Card - 18 -... -
Page 23: Step 11 Connect External Peripherals To Back Panel
Step 11 Connect External Peripherals to Back Panel You are now ready to connect the external peripherals to your system's back panel. 1. PS/2 Mouse Port 2. PS/2 Keyboard Port 3. Parallel Port 4. Serial Port 5. VGA Port 6. Game Port 7. -
Page 24: Step 12 System Boot Up For The First-Time
Step 12 System Boot Up For the First-Time To ensure your system completedly and correctly installed, please refer to the above installation steps once again before first booting up your system. 1. Insert a system-bootable floppy disk (DOS 6.2X, Windows 9X/NT, or others), which contains the FDISK and FORMAT utilities. -
Page 25: Step 13 Install Drivers & Software Components
2000/ME/NT/XP operating systems. Make sure your operating system is already installed before running the installation programs on CD-ROM. 1. Insert the MS52PN bundled CD-ROM into your CD-ROM drive. The auto-run program will display the main installation window on screen. 2. Choose "Install SIS AGP Driver" and complete it. -
Page 26: Jumper Settings
3.2 Jumper Settings Several hardware settings are made through the use of mini jumpers to con- nect jumper pins on the mainboard. Pin #1could be located at any corner of jumpers, and the corner with a white right angle stands for Pin #1. There are several types of Pin #1 as shown below: 3-pin and multi-pin (>3) jumpers shown as follows: Pin #1 to the left:... -
Page 27: Jumpers & Connectors Guide
Jumpers & Connectors Guide Refer to the mainboard layout on page 10 and this section to help you iden- tify jumpers, slots, and connectors along with their assigned functions. B2~B4 B5~B8 B9~B10 C1~C4 CPU/Memory/Expansion Slots Socket 478 : CPU socket for Intel Pentium 4, 478-pin processor DIMM1/2 : Three DIMM slots for 128, 256, 512 MB, and 1GB of 2.5V DDR SDRAM... -
Page 28: Jumpers
Jumpers : Clear CMOS setting : BIOS Protect setting Back Panel Connectors PSKBM1 : PS/2 mouse port PSKBM1 : PS/2 keyboard port LPT1 : Parallel port COM1 : Serial port1 VGA1 : VGA port1 GAME : Game port Line-Out : Line-Out port Line-In : Line-In port Microphone... - Page 29 : IR header CDIN1/CDIN2 : Primary/Secondary CD_IN connectors WOM1 : Wake On Modem connector WOL1 : Wake On LAN connector - 25 -...
-
Page 30: Clear Cmos Setting (Jp1)
Jumpers Clear CMOS Setting (JP1) JP1 is used to clear CMOS data. Clearing CMOS will result in permanently erasing previous system configuration settings and the original factory-set system settings. Pin 1-2 (Normal)(Default) Pin 2-3 (Clear CMOS) Step 1. Turn off the system power (PC-->Off). Step 2. -
Page 31: Back Panel Connectors Ps/2 Mouse & Ps/2 Keyboard Port Connectors
Back Panel Connectors PS/2 Mouse & PS/2 Keyboard Port Connectors PS/2 Mouse Two 6-pin female PS/2 Mouse & Keyboard connectors are located on the rear panel of the mainboard. In a desktop computer, the PS/2 Mouse connector is situated on the top of the PS/2 Keyboard connector. -
Page 32: Line_Out Port Connector
Line-Out Port Connector Line-Out is a stereo output port through which the combined signal of all internal and external audio sources on the board Line-Out Port is output. It can be connected to 1/8-inch TRS stereo headphones or to amplified speakers. -
Page 33: Front Panel Connectors Hdd Led Connector (Hddled)
Front Panel Connectors HDD LED Connector (HDDLED) Attach a connector cable from the IDE device LED to the 2-pin (HLED) header. The HDD LED lights up whenever an IDE device is active. Front Panel PANEL1 Power/Sleep/Message waiting LED (ACPILED) Connecting pins 2 and 4 to a single or dual color, front panel mounted LED provides power on/off, sleep, and message waiting indication. -
Page 34: Hardware Reset Connector (Rst)
Hardware Reset Switch Connector (RST) Attach a cable to the 2-pin (RST) header. Pressing the reset switch causes the system to restart. Front Panel PANEL1 ATX Power On/Off Switch Connector (PWR_SW) The Power On/Off Switch is a momentary type switch used for turning on or off the ATX power supply. -
Page 35: Front Panel Audio Header (Audio1)
Front Panel Audio Header (AUDIO1) This header allows users to install an auxiliary Front-Oriented Audio port for easier access. Either the Line-Out port connector on back panel or the front panel Audio header is available at the same time. If you would like to use this header on front panel, please remove all jumpers from it and install your spe- cial extra audio cable instead. -
Page 36: Internal Peripheral Connectors Enhanced Ide And Floppy Connectors (Ide1/Ide2 & Fdd1)
Internal Peripheral Connectors Enhanced IDE and Floppy Connectors (IDE1/IDE2 & FDD1) MS52PN motherboard features two 40-pin dual-channel IDE device connec- tors (IDE1/IDE2), providing support for up to four IDE devices, such as CD- ROM and Hard Disk Drive (HDD). This mainboard also includes one 34-pin floppy disk controller (FDC) to accommodate the Floppy Disk Drive (FDD). -
Page 37: Other Connectors Atx Power Supply Connectors (Atx1/Atx2)
Other Connectors ATX Power Supply Connectors (ATX1/ATX2) This motherboard uses 20-pin ATX power header (ATX2), and comes with the other one header (ATX1). Please make sure you plug each in the right direction. It is essential to have these two power supply connectors plugged or your system won't boot up. -
Page 38: Fan Connectors (Cpufan1/Pwrfan1/Casfan1)
Fan Connectors (CPUFAN1/PWRFAN1/CASFAN1) The mainboard provides three onboard 12V cooling fan power connectors to support the CPUFAN1/PWRFAN1/CASFAN1. CPUFAN1 Note: Both cable wiring and type of plug may vary, which depend on the fan maker. Keep in mind that the red wire should always be connected to the +12V header and the black wire to the ground (GND) header. -
Page 39: Cd_In Connectors (Cdin1/Cdin2)
CD_IN Connectors (CDIN1/CDIN2) Ports CDIN 1 (Black)/CDIN 2can be used to connect stereo audio inputs from CD-ROM, TV-tuner or MPEG card. CD1/2 CDIN1 CDIN2 Pin Assignments (CDIN1): 1=CD In-L 2=GND 3=GND 4=CD In-R Pin Assignments (CDIN2): 1=GND 2=CD In-L 3=GND 4=CD In-R Wake On Modem (WOM1)/ Wake On LAN (WOL1) Connectors... -
Page 40: System Memory Configuration
3.3 System Memory Configuration The MS52PN mainboard has two 184-pin DIMM slots that allow you to install from 32 MB up to 1GB of system memory. Each 184-pin DIMM (Dual In-line Memory Module) slot can accommdate 32 MB, 64 MB, 128MB, 256MB, 512MB, and 1GB compliant 2.5V single or double side 64-bit wide... -
Page 41: Software Utility
D:\Autorun.exe (assuming that your CD-ROM drive is drive D:) Navigation Bar Description: F Install MS52PN Software - Installing SIS AGP, SIS IDE, SIS VGA, SIS USB 2.0, Realtek LAN, C-Media Audio Drivers. F Manual - MS52PN mainboard user's manual in PDF format. -
Page 42: Install Mainboard Software
Insert the attached CD into your CD-ROM drive and the CD AutoRun screen should appear. Select using your pointing device (e.g. mouse) on the “Install Mainboard Software“ bar to run into sub-menu. The MS52PN Softwaree includes: [4.2.A] Install SIS AGP Driver [4.2.B] Install SIS IDE Driver [4.2.C] Install SIS VGA Driver... -
Page 43: A Install Sis Agp Driver
4.2.A Install SIS AGP Driver Select using your pointing device (e.g. mouse) on the “Install SIS AGP Driver" bar to install the SIS AGP driver. Once you made your selection, a Setup window run the installation automatically. When the copying files is done, make sure you reboot the system to take the... -
Page 44: C Install Sis Vga Driver
4.2.C Install SIS VGA Driver Select using your pointing device (e.g. mouse) on the “Install SIS VGA Driver" bar to install the SIS VGA driver. Once you made your selection, a Setup window run the installation automatically. When the copying files is done, make sure you reboot the system to take the... -
Page 45: E Install Realtek Lan Driver
4.2.E Install Realtek LAN Driver Select using your pointing device (e.g. mouse) on the “Install Realtek LAN Driver” bar to install Realtek LAN driver. Once you made your selection, a Setup window run the installation automatically. When the copying files is done, make sure you reboot the system to take the installation effect. -
Page 46: View The User's Manual
4.3 View the User's Manual Click on the "Manual" bar, and on the submenu click on the "Install Acrobat Reader" bar if you need to install it. Click on the "Manual" bar to view MS52PN user's manual. - 42 -... -
Page 47: Bios Setup
5 BIOS SETUP MS52PN BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in battery-backed RAM so that it retains the Setup information even if the system power is turned off. -
Page 48: The Main Menu
5.2 The Main Menu Once you enter the Award BIOS(tm) CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Enter>... - Page 49 PnP/PCI Configurations This option configures how PnP (Plug and Play ) and PCI expansion cards operate in your system. PC Health Status This entry shows the current system temperature, voltage, and fan speed. Frequency/Voltage Control Use this menu to specify your settings for the frequency/voltage control. Load Fail-Safe Defaults Use this menu to install fail-safe defaults for all appropriate items in the setup utility.
-
Page 50: Standard Cmos Features
Standard CMOS Features Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item. Date (mm : dd : yy) Set the system date. Note that if you are running a Windows OS, this items are automatically updated whenever you make changes to the Windows Date. - Page 51 Base Memory/Extended Memory/Total Memory These items are automatically detected by the system at start up time. These are display-only fields. You can't make change to these fields. ****************************************************** IDE Adapters The IDE adapters control the hard disk drive. Use a separate sub-menu to configure each hard disk drive.
-
Page 52: Advanced Bios Features
Advanced BIOS Features This section allows you to configure your system for basic operation. CPU Feature Scroll to this item and press <Enter> to view the following screen, and the following items are only available when the motherboard supports Prescott CPU: Ø... - Page 53 Hard Disk Boot Priority This item let you select hard disk boot priority. Ø The choice: Pri.Master/Slave, Sec.Master/Slave, USB HDD 0~2, Bootable Add-in Cards. CPU L1&L2&L3 Cache All processors that can be installed in this mainboard use internal level1(L1) , external level 2(L2) cache memory and (L3) to imporve performance. Leave this item at the default value for better performance.
- Page 54 Boot Up Floppy Seek If this item is enabled, it checks the size of the floppy disk drives at start- up time. You don't need to enable this item unless you have a legacy diskette drive with 360k capacity. Ø The choice: Enabled or Disabled. Boot Up NumLock Status This item defines if the keyboard Num Lock key is active when your system is started.
- Page 55 OS Select For DRAM > 64MB This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating system. Otherwise, leave this item at the default. Ø The choice: Non-OS2 or OS2. HDD S.M.A.R.T Capability The S.M.A.R.T.
-
Page 56: Advanced Chipset Features
Advanced Chipset Features These items define critical timing parameters of the mainboard. You should leave the items at their default values unless you are very familiar with the technical, specifications of your system hardware. If you change the val- ues incorrectly, you may introduce fatal errors or recurring instability into your system. - Page 57 RAS Precharge Time (tRP) This is the duration of the time interval during which the Row Address Strobe signal to a DRAM is held low during normal Read and Write Cycles. Ø The choice: 2T~5T. RAS to CAS Delay (tRCD) This is the amount of time a CAS is performed after a RAS.
-
Page 58: Integrated Peripherals
Integrated Peripherals OnChip IDE Device Press <Enter> to enter the sub-menu of detailed options. Internal PCI/IDE Use these items to enable or disable the internal PCI IDE channels that are integrated on the motherboard. Ø The Choice: Disabled, Primary, Secondary or Both. IDE Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE inter-... - Page 59 IDE Burst Mode This option, when enabled will instruct the system to send every write transaction to the write buffer. Ø The Choice: Enabled or Disabled. OnChip PCI Device Press <Enter> to enter the sub-menu of detailed options. USB Controller This item enables the USB controller.
- Page 60 Onboard Serial Port 1 The option is used to assign the I/O address and interrupt request (IRQ) for the onboard serial port 1 (COM1). Ø The Choice: Disabled, 3F8-IRQ4, 2F8-IRQ3, 3E8-IRQ4, 2E8-IRQ3, or Auto. Onboard Serial Port 2 The option is used to assign the I/O address and interrupt request (IRQ) for the onboard serial port 2 (COM2).
- Page 61 Onboard LAN Device This item allows you to set LAN device. Ø The choice: Enabled or Disabled. Onboard LAN Boot ROM Decide whether to invoke the boot ROM of the onboard LAN chip. Ø The choice: Enabled or Disabled. IDE HDD Block Mode If your IDE hard drive supports block mode select Enabled for auto- matic detection of the optimal number of block read/writes per sector the drive can support.
-
Page 62: Power Management Setup
Power Management Setup The Power Management Setup allows you to configure your system to most effectively saving energy while operating in a manner consistent with your own style of computer use. ACPI Suspend Type This item allows you to select sleep state when suspend. In the default, S1(POS), the suspend mode is equivalent to a software power down;... - Page 63 MODEM Use IRQ If you want an incoming call on a modem to automatically resume the system from a power-saving mode, use this item to specify the interrupt request line (IRQ) that is used by the modem. Ø The choice: Auto or 3~11. HDD Off After The IDE hard drive will spin down if it is not accessed within a specified length of time.
- Page 64 Resume By PCI PME This item specifies whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected. Ø The choice: Enabled or Disabled. Resume By USB (S3) This option allows the activity of the USB devices (keyboard and mouse) to wake-up the system from S3 sleep state.
- Page 65 PCI PIRQ[A-D]# When disabled, any PCI device set as the Master will not power on the system. Ø The choice: Enabled or Disabled. Delay Prior to Thermal The item allows you to set delay prior to thermal. Ø The choice: None, 1Min, 2 Min, 4 Min, 8 Min, 16 Min, 32 Min or 64 Min.
-
Page 66: Pnp/Pci Configurations
PnP/PCI Configurations This category configures how PnP and PCI operate in your system. Correctly setting up the IRQ and DMA (both PnP and PCI use) assign- ments will make your system work stably. It is strongly recommended that only technical users make changes to the default settings. Reset Configuration Data When enabled, any PnP configuration data stored in the BIOS will be cleared from memory, with new data created. - Page 67 INT Pin 1~8 Assignment Names the interrupt request (IRQ) line assigned to a device connected to the PCI interface on your system. Ø The Choice: Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, or 15. - 63 -...
-
Page 68: Pc Health Status
PC Health Status Shutdown Temperature Enables you to set the maximum temperature that system can reach before powering down. Ø The choice: 60°C/140°F, 65°C/149°F, 70°C/158°F, or Disabled. The following items provide you with information about the system's current operating status. You cannot make changes to one of them. CPU Core Voltage +1.8V +3.3V... -
Page 69: Frequency/Voltage Control
Frequency/Voltage Control CPU Clock Ratio Use the CPU Host/SDRAM/PCI Clock to set the frontside bus frequency for the installed processor (usually 133 MHz, 100 MHz or 66 MHz). Then use CPU Clock Ratio Jumpless to set a multiple. The multiple times the frontside bus must equal the core speed of the installed pro- cessor e.g., 3.5 (multiple) x100 MHz (frontside bus) = 350 MHz (in- stalled processor clock speed). -
Page 70: Load Fail-Safe Defaults
Load Fail-Safe Defaults When you press <Enter> on this item, you will get a confirmation dialog box with a message similar to: Load Fail-Safe Defaults (Y/N) ? N Pressing 'Y' loads the BIOS default values for the most stable, minimal performance system operations. -
Page 71: Set Supervisor/User Password
Set Supervisor/User Password Steps to set supervisor/user password are described as follows: New Password Setting: 1. While pressing <Enter> to set a password, a dialog box appears to ask you enter a password. 2. Key in a new password. The password can not exceed eight charac- ters. -
Page 72: Save & Exit Setup
Save & Exit Setup Pressing <Enter> on this item asks for confirmation: SAVE to CMOS and EXIT (Y/N)? Y Pressing "Y" stores the selections made in the menus of CMOS - a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS.
Need help?
Do you have a question about the MS52PN and is the answer not in the manual?
Questions and answers