Related Manuals for EASTMAN Kodak RP X-Omat Processor M6B
Summary of Contents for EASTMAN Kodak RP X-Omat Processor M6B
- Page 1 Publication No. 1C7070 May 1994 Supersedes 2B6835 July 1993 635883 April 1988 SITE SPECIFICATIONS for the Kodak RP X-Omat Processor, Model M6B H048_0086DA © Eastman Kodak Company, 1994...
- Page 2 No patent license is granted by this information. Eastman Kodak Company reserves the right to change this information without notice, and makes no warranty, express or implied, with respect to this information. Kodak shall not be liable for any loss or damage, including consequential or special damages, resulting from the use of this information, even if loss or damage is caused by Kodak’s negligence or...
-
Page 3: Table Of Contents
Table of Contents Description Page Introduction................................5 Dimensions and Weights ............................6 Electrical Requirements ............................7 Basic Requirements ............................7 Standard Service Options..........................7 Water and Drain Requirements ..........................8 Water Supply ..............................8 Drain..................................8 Environmental Requirements ..........................9 Room Ambient Temperature ..........................9 Air and Heat..............................9 Diagrams ................................11 Center of Gravity..............................21 1C7070... - Page 4 BLANK PAGE 1C7070...
-
Page 5: Introduction
Parts List Publication 1C7061 1C7070 635812 635828 635860 Part No. Available It is recommended that these publications be kept in the binder provided. If an individual document gets misplaced or destroyed, reorder a copy from your Eastman Kodak Representative. 1C7070... -
Page 6: Dimensions And Weights
Dimensions and Weights Table 1 Dimensions and Weight of the Processor Description Crated Uncrated Length 71.1 cm (28 in.) 63.5 cm (25 in.) Without feed tray (Includes knobs and fittings.) 97.8 cm (38.5 in.) With feed tray (Includes dryer knob.) Width 90.2 cm (35.5 in.) 76.2 cm (30 in.) -
Page 7: Electrical Requirements
Electrical Requirements IMPORTANT Basic Requirements In addition, all electrical services, including earth ground, must comply with local and national electrical codes. • 30 A, single-phase, 208/220, 3-wire, earth ground required. • Main Power Disconnect (wall-mounted, not furnished) The main power disconnect switch must consist of a minimum 2-pole thermo-magnetic circuit breaker with solid neutral and common trip, or a fused disconnect switch. -
Page 8: Water And Drain Requirements
Water and Drain Requirements Processor Supply Water Supply (1) Temperature: 4° to 29.4°C (40° to 85°F) NOTE If the upper limit of the room ambient or the water supply temperature to the processor is exceeded, the developer temperature may not be controlled correctly. A water chiller may be required. -
Page 9: Environmental Requirements
Environmental Requirements • Temperature: 15° to 30°C (59° to 86°F) Room Ambient Temperature • Humidity: 15% to 76% NOTE If the upper limit of the room ambient or the water supply temperature to the processor is exceeded, the developer temperature may not be controlled correctly. - Page 10 Measurement can be made using an Air Meter, available through Service Parts Management as TL-2431. Measurement of negative air within flexible duct hoses will be simplified with the use of a modified Chemical Replenisher Check Tube P/N 592380, cut to a 30.5 cm (12 in.) straight line length, and connected to the rubber hose supplied with the Air Meter.
-
Page 11: Diagrams
Diagrams FIXER DRAIN VALVE FEED TRAY and SHELF INTERFACE JACK RUN SWITCH RUN SWITCH SAFELIGHT/ ACCESSORY RECEPTACLE WATER DRAIN VALVE WASH OVERFLOW MAIN and DRAIN CIRCUIT BREAKER FIXER OVERFLOW and DRAIN DEVELOPER FIXER OVERFLOW AUXILIARY and DRAIN DRAIN BUZZER DEVELOPER WATER INLET AUXILIARY U.S. - Page 12 TOP COVER DISPLAY PANEL RECEIVING H048_0086DCA H048_0086DA Figure 3 Receiving-End View of the Processor DEVELOPER DRYER REPLENISHMENT REPLENISHMENT TEMPERTURE SWITCH FLOAT CONTROL FIXER DEVELOPER DEVELOPER REPLENISHMENT DRYER INDICATOR INDICATOR TEMPERATURE H048_0025BCC FLOAT LAMP LAMP METER H048_0025BA Figure 4 Display Panel on Receiving-End of the Processor 1C7070...
- Page 13 762 mm (30.00 in.) 196 mm 196 mm (7.75 in.) (7.75 in.) 114 mm 83 mm (4.50 in.) (3.25 in.) 57 mm (2.25 in.) 77 mm (3.12 in.) 248 mm (9.75 in.) 63 mm (2.50 in.) 1232 mm (48.50 in.) 425 mm (13.25 in.) 590 mm...
- Page 14 HOT WATER SUPPLY Mixing faucet with hose bib COLD WATER SUPPLY PLATFORM FINISHED FLOOR H048_0120DCA H048_0120DA Figure 6 Replenisher Tanks Table 5 Dimensions for Replenisher Tanks DESCRIPTION DIMENSION 14 GAL 30 GAL 55 GAL Max Platform Height ‘‘A’’ Fig. 14 48.3 cm (19 in.) 35.6 cm (14 in.) 15.2 cm (6 in.)
- Page 15 H108_0006DA Figure 7 Suggested Room Layout and Drain Locations Table 6 Maintenance and Operation Access Requirements Description Recommendation Receiving-End of Processor 91.4 cm (36 in.) Feed-End of Processor 91.4 cm (36 in.) Drive-Side of Processor 91.4 cm (36 in.) Non-Drive Side of Processor 91.4 cm (36 in.) Top of Processor 91.4 cm (36 in.)
- Page 16 SAFELIGHT FIXTURE (not furnished) connect to safelight outlet of processor (for visual feed indicator) ROOMLIGHT 121.9 cm DARKROOM (48.0 in.) AREA AREA minimum LIGHT-TIGHT GASKET compress to approx. 57.2 cm 38.1 cm 1.0 cm (.38 in.) (22.5 in.) (15.0 in.) upon installation 5.1 cm (2.0 in.)
- Page 17 H108_0009DAA H048_0089DA Figure 9 Electrical and Water Connections NOTE • Pass service through the wall to the feed-end of the processor in the darkroom. Service controls may be located on either side of the processor for easy accessibility. • See the Table on page 18. 1C7070...
- Page 18 A mixing valve is not required for the processor if incoming water temperature is between 4° and 29.4°C (40° and 85°F). Shutoff Valves ⁄ in. NPT. Two additional required. Available from Eastman Kodak Company, Part No. 459981. Not supplied with the Processor. Cold Water Supply ⁄...
- Page 19 BOLT WASHER BRACKET ANCHOR FLOOR H048_0005DCA H048_0005DA Figure 10 New Wall Installation If the wall around the opening is straight and exactly perpendicular to the floor, this panel may not be necessary. The wall opening dimensions should match the inside dimensions of the panel opening. Make sure that the vertical dimension of 48 ±...
- Page 20 H048_0091ACA Inlets for Replenishment Tubing H048_0091AA Figure 11 Inlets for Replenisher Tubing H048_0006DA Figure 12 Alternate Inlets for Replenisher Tubing 1C7070...
-
Page 21: Center Of Gravity
Center of Gravity FEED TRAY SIDE 123.2 cm (48.5 in.) Center of Gravity with TANKS empty 34.0 cm 38.8 cm (13.14 in.) (15.29 in.) 72.2 cm (28.43 in.) 57.2 cm (22.5 in.) 76.2 cm (30.0 in.) H048_0117DA Figure 13 Center of Gravity NOTE Center of gravity is shown for the processor with the DEVELOPER, FIXER, and WASH TANKS empty. - Page 22 3040SS_B.TXT Kodak and X-Omat are trademarks. Health Sciences Division EASTMAN KODAK COMPANY • ROCHESTER, N.Y. 14650 Printed in USA...
Need help?
Do you have a question about the Kodak RP X-Omat Processor M6B and is the answer not in the manual?
Questions and answers