Pyronix Enfoecer KF4-WE Quick Start Manual

KF4-WE
Wireless keyfob
4 button, two way
The KF4-WE Buttons
Lock Button
Status LED
I Button
II Button
Specifications
Transmission Frequency: 868MHz
Transmission Method: Fully encrypted rolling code
Transmission Range: 300m free space
Low Battery Threshold: 2.1V +/-5% at 25°C
Code Combinations: 4294967295
Battery: CR-1/3N Li-Mn Cell (3 volts)
Battery Life: Up to 2 years
Operating Temperature: -10 to +40 °C
Emissions: EN55022 Class B
Immunity: EN50130-4
Dimensions: 60 x 40 x 15 mm
Weight: 28g
KF4-WE Learning
1. Put the Enforcer control panel into
the "Change Codes" menu (see
Enforcer User Manual for full details).
2. When prompted to enter a new user
code, press any keyfob button.
3. Once asterisks appear on the
Enforcer keypad, the new keyfob is
learned on the system.
RINS1434-2
Changing The Battery
The batteries supplied have been chosen to
provide long service life whilst, for safety
reasons, having limited output current.
Replace only with approved batteries.
Unlock Button
To prevent possible damage to components,
any static charge on your body needs to be
eliminated before touching the inside of the
unit. This can be accomplished by touching
some grounded/earthed metallic conductor
such as a radiator/pipework immediately
before replacing the batteries.
Certification
WARRANTY: This product is sold subject to our
standard warranty conditions and is warranted
against defects in workmanship for a period of one
years. In the interest of continuing improvements
of quality, customer care and design, Pyronix ltd
giving prior notice. (Batteries not included in warranty)
Locking the Keyfob
All 4 buttons on the keyfob may be locked so that any accidental
presses won't affect your alarm system.
Locking the keys on the keyfob is performed by pressing any buttons
that are diagonal with one another at the same time; ie Lock & II or
Unlock & I.
The RED LED will flash indicating that the fob has been locked.
To unlock, press both buttons together again, and the GREEN LED
will flash indicating that the keyfob is now unlocked.
Note: When locked, the LED status is disabled.
When disposing of the
product, the battery must be
removed and disposed of
separately in accordance
with the local regulations
-
(Negative)
+
(Positive)
CR-1/3N Li-Mn Cell (3 volts)
For electrical products sold within the
European Community. At the end of the
electrical products life, it should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice in your country.
EN50131-3:2009
EN50131-5-3:2005+A1:2008
Security Grade 2
Environmental Class II
Resetting the keyfob
To do a nvm reset on the keyfob, first remove the
battery, then press and hold down the lock and
unlock buttons together and reinsert the battery at
the same time. Continue holding down the buttons
for another 10 seconds and then release.
Status LEDs
The fully two way wireless keyfob allows you to see
the status of the control unit via 3 colour LEDs:
System Armed: When the system is armed a RED
LED will illuminate momentarily.
System Disarmed: When the system is disarmed a
GREEN LED will illuminate momentarily.
System Fault: When the system is in fault condi-
tion an AMBER LED will illuminate momentarily, this
will also flash when the keyfob is unable to arm
itself in the correct mode without you having to
choose.
Pyronix Ltd
Braithwell Way
Hellaby
Rotherham
South Yorkshire
S66 8QY
Customer Support:
+44(0)845 6434 999 (local rate)
or +44(0)1709 535225
Hours: Mon to Fri, 8:00am till 6:30pm
Email: customer.support@pyronix.com
Website: www.pyronix.com