Technical Data; Definitions: Safety Guidelines - DeWalt XR Li-Ion DCD999 Manual

IMPACT DRILL
DCD999
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.

Technical Data

Voltage
Type
Battery type
No load speed
1st gear
2nd gear
3rd gear
Impact rate
1st gear
2nd gear
3rd gear
Max. torque (hard/soft)
hard
soft
Chuck capacity
Maximum drilling capcity
Wood
Metal
Masonry
Weight (without battery pack)
Noise values and vibration values (triax vector sum) according to EN60745-2-1:
L (emission sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given
sound level)
Drilling into metal
Vibration emission value a
h,D
Uncertainty K =
Impact drilling
Vibration emission value a
h,ID
Uncertainty K =
Screwdriving
Vibration emission value a =
h
Uncertainty K =
Power
WALT one of the
e
DCD999
V 18
DC
1
Li-Ion
Drill, Driver/Hammer
min 0–450/500
-1
0–1300/1500
0–2000/2250
min 0–8500
-1
0–25500
0–38250
DCB546
Nm 112
Nm 66
mm 1.5–13
mm 55
15
13
kg 1.61
dB(A) 94
dB(A) 105
dB(A) 3
= m/s 2 2.7
m/s 2 1.5
= m/s 2 12.5
m/s 1.5
2
m/s < 2.5
2
m/s 1.5
2
DCB184 DCB546
UWO 860 1219
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised
test given in EN60335‑2‑69 and may be used to compare one
tool with another. It may be used for a preliminary assessment
of exposure.

WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However
if the tool is used for different applications, with different
accessories or poorly maintained, the vibration and/or
noise emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool
is switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm
(relevant for vibration), organisation of work patterns.
EC‑Declaration of Conformity
DCB547
Machinery Directive
126
67
Impact Drill
DCD999
D WALT declares that these products described under
e
Technical Data are in compliance with:
2006/42/EC, EN60745‑1:2009+A11:2010, EN60745‑2‑1:2010.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact D
the following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of D
Markus Rompel
Vice‑President Engineering, PTE‑Europe
D WALT, Richard‑Klinger‑Straße 11,
e
65510, Idstein, Germany
19.08.2020
a
WARNING: To reduce the risk of injury, read the
instruction manual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each
DCB547
signal word. Please read the manual and pay attention to
1296
these symbols.
English
WALT at
e
WALT.
e
3