Page 1
参考色:PANTONE Cool Gray 11 C 艺 PANTONE 185 C 要 尺寸偏差:±0.5mm 求 印刷偏位:±1mm Roborock S7 Robot Vacuum Cleaner User Manual 130mm 备 注 Read this user manual carefully before using this product and store it properly for future reference. 项目名称...
Page 2
Roborock S7 Robot Vacuum Cleaner User Manual Read this user manual carefully before using this product and store it properly for future reference.
Safety Information IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL IN- STRUCTIONS BEFORE USING (THIS APPLIANCE), Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING To reduce the risk of fire, electric shock, or injury: •...
Page 4
Safety Information • For use only with roborock CDZ11RR or CDZ12RR charger. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Page 5
Safety Information • Risk Of Injury. Brush May Start Unexpectedly.Disconnect the main Brush Before Cleaning or Servicing. • Do not use the product when the temperature is higher than 40℃ or lower than 4℃, or there is any liquid or sticky sub- stance on the floor.
Page 6
à la position marche peut causer un accident. • Pour emploi seulement avec roborock CDZ11RR or CDZ12RR chargeur.Recharger uniquement avec le chargeur prescrit par le fabricant. Un chargeur convenant à un type de batterie peut présenter un risque d’incendie lorsqu’il est utilisé avec une autre batterie.
Safety Information • Ne pas exposer une batterie ou un appareil à la flamme ou à des températures excessives. L’ e xposition à une flamme ou à des températures supérieures à 130 °C peut causer une explosion. • Respecter toutes les instructions de chargement et ne pas charger la batterie ou l’appareil à des températures qui ne sont pas incluses dans la gamme de températures indiquées dans la notice d’instructions.
Compliance Information Product Name Robotic Vacuum Cleaner with Dock Charger Robotic Vacuum Cleaner Model: roborock S7 Produce Model Dock Charger Model: CDZ11RR or CDZ12RR This device complies with part 15 of the FCC Rules. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innova- tion, Science and Economic Development Canada's licence-exempt RSS(s).
Page 9
FCC IC Statement L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Battery and Charging • Please keep the dock charger away from heat (such as heating plates). • Do not wipe or clean the chargers shrapnel with a piece of wet cloth or wet hands. • Please make sure the cleaner is powered off in shipment and original packaging is advised. •...
Product overview Robot Status Indicator Light • White: Vacuuming • Blue: Vacuuming and mopping • Orange: Refill • Blue + White: Preparing to mop Dock • Press to return to the dock Clean/Power Power Indicator • Press to clean • White: Battery level ≥ 20% •...
Page 14
Product overview Sensors Wall Sensor Dock Locator Cliff Sensors Carpet Sensor Bumper Omni-Directional Wheel Charging Contacts LiDAR Sensor Side Brush Main Wheels Vertical Main Brush Bumper Main Brush Cover Latch Water Tank Latch...
Page 15
Product overview VibraRise Module Water Tank Stopper Water Filter Water Tank Latch Electric Water Tank Mop Cloth Attachment Slot Vibration Module Mop Cloth Bracket Latch VibraRise Mop Cloth Bracket Attachment Area Mop Cloth...
Product overview Charging Dock Charging Dock Power Dock Location Beacon Charging Contacts Rear Cover Cable Slot Power Socket Cable Slot Opening Note: Cables can exit from the left or right openings.
Installation Important Tidy cables and loose items from the ground and move any If using this robot in a raised area, always use a secure physical unstable, fragile, precious, or dangerous objects to prevent barrier to prevent accidental falls that may result in personal personal injury or property damage due to things becoming injury or property damage.
Page 18
Installation Position the charging dock Power on and charge the robot Keep the charging dock on a level surface, flat against a wall. Press and hold the button to power on the robot. When Connect the power cable to the charging dock and place any the power light goes on, place it on the dock to charge.
Page 19
Installation Mopping the floor 3. Reinstall the water tank Slide the water tank along the grooves until you hear it click in Note: To prevent excessive buildup of dirt on the mop, floors should be vacuumed at place. least three times before the first mopping cycle. 1.
Page 20
Installation 5. Install the mop cloth bracket 6. Remove the mop cloth bracket Slide the vibrating mop cloth bracket along the bottom of the After returning to the dock, remove the mop cloth bracket by water tank until you hear it click in place. pressing both side latches and sliding back.
Risk of injury do not put your hand into the seam, it may cut your Downloading the app finger. 1. Search for "Roborock" in the App Store or Google Play or scan the QR code to download and install the app. 2. Search for "Mi Home" in the App Store or Google Play or...
Connecting to the App Reset WiFi Add device 1. Open the upper cover and find the WiFi indicator. On the app homepage, tap "+" in the top right corner and 2. Press and hold the buttons until you hear the follow the prompts to add a device.
Instructions On/Off Note: • Cleaning cannot start if the battery level is too low. Allow the robot to charge before start- ing cleanup. Press and hold the button to turn on the robot. The power in- • Before cleaning, tidy cables (including the charging dock power cable) and fragile items dicator will turn on, and the robot will enter standby mode.
Page 24
Instructions Spot Clean Pause Press to start Spot cleaning. During a clean, press any button to pause, press to continue, or Area: 1.5m (4.9ft) square centered on the robot. press to send the robot back to the dock. Note: After spot cleaning, the robot will return to the starting point and enter Standby Note: Placing a paused robot on the charging dock will end the current cleanup.
Instructions Charging Selective Room Cleaning The robot will return to the charging dock automatically after The robot will clean the areas selected in the app. finishing. If it is paused, press the button to send it to the Note: charging dock. The power indicator will flash slowly as the robot •...
Instructions Scheduled Cleaning Firmware Updates Set cleaning schedules, and at the defined times, the robot will Use the app to update the robot firmware. Update when the robot clean and return to the dock. is on the charging dock and has at least 20% battery power. The power indicator will flash white quickly during the update.
Routine Maintenance To maintain optimum performance, maintain the robot according to the following guidelines: Maintenance Replacement Part Maintenance Method Frequency Frequency Omni-Directional Use a screwdriver or similar tool to pry out the axles. As required Wheel Rinse, allow to dry and press the wheel back in place. Rotate in the Unlock direction and remove.
Routine Maintenance Main Brush 1. Turn the robot over, then unlatch and remove the main brush cover. Main brush cover Latch Main brush Main brush bearing Main brush cap 2. Take out the main brush, then remove and clean the bearings.
Routine Maintenance Main brush Side Brush 3. Remove the main brush cap, rotating in the unlock direction. 1. Unscrew the side brush and remove any entangled dirt After cleaning, reattach it turning in the lock direction. 2. Reinstall and tighten in place. 4.
Page 30
Routine Maintenance Omni-Directional Wheel 1. Use a small screwdriver or similar tool to pry out the axles and 2. Rinse the wheel and axle to remove any hair or dirt. remove the wheel. Note: The omni-directional wheel bracket cannot be removed. 3.
Routine Maintenance Main Wheels Dustbin Use a soft dry cloth to wipe and clean the main wheels. 1. Open the top cover of the robot and remove the dustbin.
Page 32
Routine Maintenance Dustbin 2. Open the lid and empty the dustbin. 3. Fill it with clean water and close the lid. Gently shake the dust- bin, then pour out the dirty water. 4. Air-dry the dustbin and washable filter.
Page 33
Routine Maintenance Washable Filter 1. Open the filter cover and remove the filter. 3. Leave the filter to dry thoroughly before reinstalling it. Note: Use an alternate filter if necessary. 2. Rinse repeatedly and tap the filter frame to remove as much dirt as possible.
Routine Maintenance Water Tank 1. Open the water tank and fill it with clean water. 3. Pour out dirty water. 2. Close up the water tank and shake it gently.
Page 35
Routine Maintenance Mop cloth Robot Sensors 1. Remove the mop cloth from the mop cloth bracket. Use a soft dry cloth to wipe and clean all sensors, including: 1. The dock locator in the front 2. The wall sensor on the right. 3.
Page 36
Routine Maintenance Charging Contact Areas Battery Use a soft dry cloth to wipe the charging contacts on the charging The robot is equipped with a high-performance lithium-ion re- dock and the robot. chargeable battery pack. To maintain battery performance, keep the robot charged.
Basic Parameters Robot Charging Dock Model roborock S7 Model CDZ11RR or CDZ12RR Dimensions 353×350×96.5mm Dimensions 151×130×98mm Battery 14.4V/5200mAh lithium battery Rated Power Weight Approx. 4.7kg Rated Input 100-240V~ Wireless Connection WiFi Smart Connect Rated Output 20V 1.2A Rated Input 20V 1.2A...
Page 38
Errors If an error occurs while the robot is cleaning, the power indicator will flash red quickly, and a voice alert will sound. Refer to the following table for Troubleshooting. Error Solution Error 1: Turn the laser unit and check that it is not jammed LiDAR unit is jammed.
Page 39
Errors If an error occurs while the robot is cleaning, the power indicator will flash red quickly, and a voice alert will sound. Refer to the following table for Troubleshooting. Error Solution Error 11: Strong magnetic field detected. Move the device A high-intensity magnetic field detected.
Page 40
Errors If an error occurs while the robot is cleaning, the power indicator will flash red quickly, and a voice alert will sound. Refer to the following table for Troubleshooting. Error Solution The VibraRise module is jammed. Clear blockages and move the Error 27: VibraRise Module Jammed.
Abnormal WiFi connection. Reset the WiFi, download the latest mobile app, and retry. Unable to connect to WiFi The current Roborock robot is not supported. You can find supported models in the app. Unable to connect to WiFi. There may be an error with your router settings. Contact Robo-...
Page 42
Common Issues Problem Solution The dustbin is full and needs emptying. Poor cleaning ability or dust falling out The filter is blocked and needs cleaning. The main brush is jammed and needs cleaning. Keep the robot charged. Scheduled cleaning can only begin when the battery level is Scheduled cleaning is not working above 20%.
Page 44
Address of Manufacturer: Floor 6, Suite 6016, 6017, 6018, Building C, Kangjian Baosheng Plaza, No.8 Heiquan Road, Haidian District, Beijing, P.R.CHINA For more product information, visit our website: www.roborock.com For after-sales support, email our after-sales service team: US/Non-Europe Support: support@roborock.com...
Need help?
Do you have a question about the S7 and is the answer not in the manual?
Questions and answers