Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pilz PLID d1
Summary of Contents for Pilz PLID d1
- Page 1 PLID d1 Safety relays Operating Manual-1002227-EN-04...
- Page 2 Preface This document is the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for the user's internal purposes. Suggestions and comments for improving this documenta- tion will be gratefully received.
-
Page 3: Table Of Contents
Warranty and liability ........................ Disposal ............................ Unit features ........................... Block diagram ........................Function description ......................Installation ..........................Wiring ............................Preparing for operation ......................Dimensions in mm ......................... Technical details ........................Order reference ........................Product ............................. Accessories ..........................Operating Manual PLID d1 1002227-EN-04... -
Page 4: Introduction
PLID d1 Introduction Validity of documentation This documentation is valid for the product PLID d1. It is valid until new documentation is published. This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. -
Page 5: Safety
Short circuit, Short between contacts, Open circuit. The PLID d1 may only be used in conjunction with the evaluation device PNOZ e8.1p. The following is deemed improper use in particular Any component, technical or electrical modification to the product, Use of the product outside the areas described in this manual,... -
Page 6: Warranty And Liability
Block diagram Function description The PLID d1 sends a test pulse signal via a contact (E-STOP pushbutton or start button) to the evaluation device PNOZ e8.1p. If the line is error-free, the input circuits are closed and the contact is closed (E-STOP pushbutton or start button) a valid signal is present at the in- put S36 of the PNOZ e8.1p. -
Page 7: Installation
The cable length between PLID d1 and contact (E-STOP pushbutton or start button) should be as short as possible. Where one line is to be monitored, only use one PLID d1 and one evaluation device. Route the line so that it is protected. -
Page 8: Dimensions In Mm
A short circuit on the pushbutton or on the supply line to the pushbut- ton is not monitored! Use appropriate measures to prevent a short circuit on the pushbutton. Dimensions in mm PLID d1 (screw terminals) PLID d1 C (spring-loaded terminals) Operating Manual PLID d1 1002227-EN-04... -
Page 9: Technical Details
Rated impulse withstand voltage 0,8 kV 0,8 kV Protection type Housing IP40 IP40 Terminals IP20 IP20 Mounting area (e.g. control cab- inet) IP54 IP54 Mechanical data 774260 784260 Mounting position Max. cable length 3000 m 3000 m Operating Manual PLID d1 1002227-EN-04... -
Page 10: Order Reference
Spring-loaded terminals 784 260 PNOZ e8.1p 24 VDC Screw terminals 774 198 PNOZ e8.1p C 24 VDC Spring-loaded terminals 784 198 Accessories Product type Features Order no. PSEN bracket Mounting bracket 532 110 Operating Manual PLID d1 | 10 1002227-EN-04... - Page 11 We are represented internationally. Please refer to our homepage www.pilz.com for further details or contact our headquarters. Headquarters: Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: info@pilz.com, Internet: www.pilz.com...
Need help?
Do you have a question about the PLID d1 and is the answer not in the manual?
Questions and answers