Lamp SLUN-N Manual

ＳＬＵＮ-Ｎ
For proper installation and operation, we recommend that you read and follow these instructions carefully.
● Sugatsune cannot accept any claim for damages or injuries caused by improper use of this swing lift-up stay. Please
refer to the Model Selection section below for the proper range of use.
● Sugatsune s liability is limited to the repair or replacement of a defective product. It shall in no way extend to the
assembly as a whole.
● The utmost care was taken during the production of the SLUN-N. Should you however notice any defect, please
notify your local dealer or Sugatsune (export@sugatsune.co.jp ) .
● The warranty period extends to one year from the shipping date.
● For improvement reasons, the content of this set may be changed without prior notice. We recommend that you check
carefully the set content against the part list shown below and report any discrepancy to your local dealer before
installation.
● Operating temperature is 5〜35℃. Function may vary depending on the temperature.
Do not force the door open past its fully opened position.
!
Do not use in excessively hot environment such as to hide an oven.
!
Do not insert your hand or finger between the arms as this may lead to sever injury.
!
Never attempt to open or disassemble the mechanism as this may lead to injury.
!
Do not pull the arm down as it will spring back up violently and may cause serious injuries.
!
Parts list
Arm A
Fig.１
①SLUN-N(R) right-
hand side body
1pcs
Binding tapping screw(3.5×15)
④
⑤Damper ⑥Holder ⑦Distance plate
2pcs
2pcs 2pcs
*SLUB Bars are available in 4 standard sizes : 535、835、551 and 851mm.
⑧Countersunk tapping screw(3.5×20)
6pcs
Model slection
W ＝ Cabinet width
0
T ＝ Cabinet side panel thickness
h ＝ Cabinet inside height
t
Fig.２ ＝ Cabinet top board thickness
Ｗ ＝ Door width
1
Ｗ
H ＝ Door height
0
1
t
Ｈ
1
h
T
Ｗ
1
SWING LIFT UP MECHANISM
Arm A
③Mounting plate ②SLUN-N(L) left-
2pcs hand side body
1pcs
Arm B Arm B
16pcs
Length of guide bar : L
⑨SLUB
Applicable door weight: Door size:
SLUN-3N 2.8〜3.8 kg Width (W
Height (H
SLUN-4N 3.8〜4.8 kg
SLUN-5N 4.8〜5.8 kg
Select the SLUN type according to the weight of the door (including
the handle).
SLUB bar needs to be cut depending on the cabinet width W
side panel thickness T.
Bar length L will depend on whether it is installed on Arm A or Arm B
(see Fig.1).
Arm A installation: L= W - ( T x 2 ) - 35
0
Arm B installation: L= W - ( T x 2 ) - 19
0

Dimensions

PAT
*The drawing shows the application
for the cabinet with 3mm thick seal
gasket on front edge.
Rubber gasket thickness A

Installation

1. Body installation:
(1) Draw a horizontal line at 354mm from the inside bottom of the cabinet.
(2) Line up the steel plate of the SLUN-N bodies ① and ② to the front of the cabinet and the line drawn in (1).
(3) Use screws ④ to secure both bodies to the cabinet.
a
a
Sold separately
3. Bar installation:
⑩Truss tapping screw
(4.5×12) 4pcs
(1) Cut the bar to the necessary length as per instructions in the Model Selection section.
(2) Install the bar to either arm A or arm B depending on the dimensions selected above. Arm A installation is
recommended for wooden doors as bar is not visible in the open position. Arm B installation is recommended
for glass door as bar is less visible in the closed position.
⑧Countersunk tapping
screw(3.5×20)
) 600、900mm
1
) 390〜450mm
1
⑥Holder ⑦Distance plate
Fig.７

Adjustment

and
0
① Loosen both a screws
② Adjust height by turn b screw
③ Refasten both a screws securely
① Loosen both c screws
② Adjust door position
③ Refasten both c screws securely
① Loosen both a screws
② Turn screw d left to bring the top of
the door closer to the cabinet
③ Refasten both a screws securely
2012.12 PRINTED IN JAPAN 0541-3
167.5
6.5
19
(95)
9 79.5
Fig.３ Dimensions
15
B = 244
E = 354
32
D = 32 + T - (
(10)
Back panel Door
W
(101.5) ＝ Cabinet width
0
Ｔ
＝ Cabinet side panel thickness
Handle
(45) h
＝ Cabinet inside height
t
＝ Cabinet top board thickness
Ｗ
＝ Door width
1
C
＝ Clearance (minimum 2
(3 is recommended)
2. Door installation:
(1) Install the mounting plates ③ to the back side of the door as per dimensions shown in Fig.3.
(2) Line up both a screws of each mounting plates with the slots of the arms and slide the door down.
a
* Make sure that the screws are properly inserted in the slots before releasing the door.
(3) Fasten both a screws securely.
Do not pull the arm down as it will spring back up violently and may cause serious injuries.
!
a
Fig.５
⑤Damper
Stopper
4. Damper installation:
(1) Line the distance plate ⑦ and the holder ⑥ with the holes for the damper (Fig.7) and
secure them with screws ⑧.
(2) Slide the damper ⑤ into the holder from the front side.
Fig.８
Fig.9
a
b
c
a
Spring strength adjustment:
Turn the screw at the back of stay body to
adjust the spring strength.
d
Spring strength should be adjusted similarly on both units.
!
Do not set the spring strength too high as the door may
!
open violently and damage the system.
c
Clearance
(minimum2 . 4)
23.5
+ t - C + ( h - 354 )
-
W W
0 1
)
2
. 4)
D ( D distance to door edge )
④Binding
tapping screw
(3.5×15)
Fig.４
⑩Truss tapping
screw(4.5×12)
06835 ⑨SLUB
(A)
Fig.６ (B)
Fig.10
① Loosen both e screws on both sides
② Adjust height of the opened door
similarly on both sides.
③ Refasten both e screws securely
e
Fig.11
-
+