Table of Contents
Advertisement
FOLDING POCKET DOOR SYSTEM ALT-F
Installation Manual
Thank you for selecting our product. Before starting installation, please read this manual thoroughly to
ensure correct installation. Please keep this manual at hand for future reference.
ABOUT THE PRODUCT
●
Pocket door hardware for folding
door system.
●
The folding door can be stored inside
the shallow cabinet.
SPECIFICATIONS
Max. door width
Max. door height
Door thickness
Max. door weight
FOR YOUR SAFE WORK AND CORRECT INSTALLATION
Meaning of symbols
Warning
Caution
WARNING:
If these warnings are not followed, it may result in death or serious injury.
It is necessary to manufacture the frame with sufficient strength so it endures the weight of the door and impact shocks upon
opening/closing the door. Also make sure to only use the designated screws and to fasten them firmly. A frame with poor
strength or loose screws might result in improper and slower movement of the door. In the worst case, the door might drop
down and cause injury.
Do not try to use this product for any other purposes other than originally intended for. Do not use the parts for applications
that are out of specification.
Do not disassemble nor modify any parts than those described in this document.
CAUTION:
If these cautions are not followed, it may result in injury or damage.
This (folding door system) should be installed by an experienced person who has correct knowledge. If the system is not
installed correctly, the door will not operate smoothly, and or may cause injury.
This (folding door system) is a part for furniture fittings. After installation, make sure to test the finished product thoroughly to
ensure that it is well-functioning and safe.
Make sure to follow the designated measurements, specifications, and horizontal/vertical angles. Make sure that the cabinet
is not warped, since it may affect the movement of the door.
If cutting any parts, make sure to remove any burr before installation. Also check the upper rail for any left-over burr or scrap
and remove these.
Make sure to check the screws for slack at regular intervals (one month from first usage, half year and then one time every
year is recommended).
2 Rails Type
450 mm / door
1830 mm
23 - 30 mm
10 kg / door
Prohibited
Required
3 Rails Type
1831 - 2400 mm
1
Advertisement
Table of Contents
Related Manuals for Lamp ALT-F18LV2
Summary of Contents for Lamp ALT-F18LV2
- Page 1 FOLDING POCKET DOOR SYSTEM ALT-F Installation Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand for future reference. ABOUT THE PRODUCT ● Pocket door hardware for folding door system.
- Page 2 PARTS SET (Single folding door) 【1】2 Rails Type: Max. door height: 1830 mm (Max. cabinet inside height: 1840 mm) Parts set Item Name: ALT-F18LV2, ALT-F18RV2, ALT-F20LV2, ALT-F20RV2 2 Rails Type Screws supplied ⑱Pan head screw (self-tapping) 4x20: 8 pcs (⑥) ⑲Truss head tapping screw 4x20: 18 pcs (①)
-
Page 3: Installation Drawings
INSTALLATION DRAWINGS The procedure describes the right handed opening type. The left-handed opening is installed in the opposite position. Item Name Opening direction Rail Length (A) Door Storing Cabinet Depth (B) ALT-F18LV2 Left 460.4 355.6 Min. 466.7 + Door thickness... -
Page 4: Cabinet Dimension
CABINET DIMENSION Upper Rail Middle Board Dimension A-A ※ Upper Rail ※ : Position (center) of φ30 hole φ30 When installing middle board Position middle board to avoid interference with handle and angle stopper. Door thickness-10 Min.120 Dimension B-B Cabinet Inside Width ＝... - Page 5 DOOR DIMENSION 【1】2 Rails Type ●Moving door ●Hanging door Hanging door Front Guide rail length = Door width - 30 Moving door Front Rear Rear 40 depth 13 φ Drill 2 holes (for hexagon flange head tapping screw 4x16) Front Rear Use hardwood for core material and make sure to tighten screws firmly to...
-
Page 6: Installation Procedures
INSTALLATION PROCEDURES Installing Parts on the Top Board ❶ to ❻. Install parts in order of ⑦Upper rail joint (Fix with ⑳screw 4x20.) ⑨Angle stopper ※ ( screw 4.5x20.) ⑬Upper rail ※ ※ See p. 4 for the length of Upper rail⑬ ( ... - Page 7 Installing Parts (1) Fix hinge set ⑯ into the hanging door. (2) Fix guide rail ⑭ into grooves in the upper blocks in hanging door. (3) Fix center hinge ⑮. 2 rails type : Fix as show in the below drawing. 3 rails type : Fix 2 center hinges within 150 mm from the end.
- Page 8 Assembling Interlock to Rail Assemble interlock⑪ to rail① with screw Interlock Rail <As assembled> screw M6x8 Installing Rails and Racks ❶Positions for rails 【1】2 Rails Type 【2】3 Rails Model Top Board Top Board Dimensions for 3 rails model Door height 1831 - 1903 1904 - 2400 Cabinet inside height: H...
- Page 9 Assembling Connecting Bar and Gear Assemble gear, connecting bar, bush, and cap as shown in the drawing. Bush CAUTION Connecting bar Make sure to check the direction of gear. Gear Be sure to push the cap into pinion shaft strongly. “THIS SIDE UP”...
- Page 10 Installing End Guide Insert the end guide ⑧ into upper rail ⑬ after height adjustment. Upper rail Top Board Top Board Door Door thickness 23 - 30 Height adjustment 23 Screw 4x16 8 End guide End guide Spring washer 4 mm Screw 4x16 CAUTION Make sure to tighten screws...
- Page 11 Assembling Hinge Cover Bracket Assemble hinge cover bracket ⑫ to rail ①. (As for 3 slides model, assemble it to middle rail, too.) Rail Hinge cover bracket Screw M6x8 <Hinge cover bracket as assembled>...
- Page 12 SUGATSUNE KOGYO CO.,LTD SUGATSUNE SHANGHAI Co., LTD SUGATSUNE AMERICA, INC Tokyo, JAPAN Shanghai, CHINA California, USA Phone: +86 21 3632 1858 E-mail:lamp@sugatsune.com.cn Phone: +81 (0)3 3866 2260 E-mail:export@sugatsune.co.jp Phone: +1 310 329 6373 E-mail:sales@sugatsune.com SUGATSUNE KOGYO (UK) LTD...
Need help?
Do you have a question about the ALT-F18LV2 and is the answer not in the manual?
Questions and answers