1. Manuals
  2. Brands
  3. GE Manuals
  4. Dryer
  5. GFD40
  6. Owner's manual

GE GFD40 Owner's Manual

Hide thumbs Also See for GFD40:
Table of Contents

Advertisement

Quick Links

Download this manual
www.GEAppliances.ca
Safety Instructions
Operating Instructions
Control Panels . . . . . . . . . . . . . . . 21-23
Cycle Options . . . . . . . . . . . . . . . . 24-25
Dryer Features . . . . . . . . . . . . . . . . . . 25
Loading and Using
the Dryer . . . . . . . . . . . . . . . . . . . . . 30-31
Venting the Dryer . . . . . . . . . . . . . . . . 32
Connecting Inlet Hoses . . . . . . . . . . . 33
Stacking . . . . . . . . . . . . . . . . . . . . . 34-37
Consumer Support
Warranty . . . . . . . . . . . . . . . . . . . . 43-44
Consumer Support . . . . . . . . . . . . . . 45
Write the model and serial
numbers here:
Model # _____________
Serial # ______________
They are on the label on
the front of the dryer behind
the door.
. . . . . . . . . 2-5
. . 6-20
. . . . 38-41
Owner's Manual
GFD40
234D1050P011
29-5889-1
11/17 ATS

Advertisement

Table of Contents
loading

Related Manuals for GE GFD40

Summary of Contents for GE GFD40

  • Page 1: Table Of Contents

    Owner’s Manual Installation Instructions . . 6–20 GFD40 Operating Instructions Control Panels ....21–23 Cycle Options ....24–25 Dryer Features .
  • Page 2 IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or death. Do not store or use gasoline or other Installation and service must be ...

  • Page 3: Installation Instructions

    IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. www.GEAppliances.ca PROPER INSTALLATION This dryer must be properly installed and located in accordance with the Installation Instructions before it is used. If you did not receive an Installation Instructions sheet, you can receive one by visiting www.GEAppliances.ca, or call 1-800-561-3344.
  • Page 4 IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. WARNING! YOUR LAUNDRY AREA  Keep the area underneath and around your  Keep all laundry aids (such as detergents, bleaches, appliances free of combustible materials (lint, etc.) out of the reach of children, preferably in a paper, rags, etc.), gasoline, chemicals and other locked cabinet.
  • Page 5 www.GEAppliances.ca WHEN USING YOUR DRYER (cont.)  Never attempt to operate this appliance if it is  You may wish to soften your laundered fabrics damaged, malfunctioning, partially disassembled, or reduce the static electricity in them by using or has missing or broken parts, including a a dryer-applied fabric softener or an anti-static damaged cord or plug.
  • Page 6 Installation Instructions / Electric Dryer WARNING! PEDESTALS FOR DRYERS (comes with individual installation instructions) FOR YOUR SAFETY: Available models: -SBSD227F Use only rigid metal or flexible metal 4-in. diameter -SBSD137H ductwork for exhausting to the outdoors. Never use plastic -SBSD107H or other combustible, easy-to-puncture ductwork.
  • Page 7 Installation Instructions / Electric Dryer www.GEAppliances.ca Minimum Clearance Other Than Alcove or Closet Installation Minimum clearance to combustible surfaces and for air opening are: 0 cm (0 in.) clearance both sides and 2.5 cm (1 in.) rear. Consideration must be given to provide adequate clearance for installation and service. PREPARING FOR INSTALLATION ELECTRICAL CONNECTION OF NEW DRYER...
  • Page 8 Installation Instructions / Electric Dryer EXHAUST INFORMATION EXHAUST CONNECTION WARNING - TO REDUCE THE RISK WARNING - USE ONLY METAL 10 cm (4”) DUCT. DO NOT USE DUCT LONGER THAN OF FIRE OR PERSONAL INJURY: SPECIFIED IN THE EXHAUST LENGTH TABLE. This dryer must be exhausted to the outdoors.
  • Page 9 Installation Instructions / Electric Dryer www.GEAppliances.ca STANDARD REAR EXHAUST (Vented above floor level) ELBOW HIGHLY RECOMMENDED RECOMMENDED CONFIGURATION TO MINIMIZE EXHAUST BLOCKAGE. ELBOW HIGHLY RECOMMENDED NOTE: ELBOWS WILL PREVENT DUCT KINKING AND COLLAPSING. LEVELING AND STABILIZING YOUR DRYER Stand the dryer upright near the final location and adjust the 4 leveling legs, at the corners, to ensure that the dryer is level from side to side and front to rear.
  • Page 10 Installation Instructions / Electric Dryer USING FLEXIBLE METAL DUCTS EXHAUSTING A CLOTHES DRYER PRODUCES COMBUSTIBLE LINT. FOR If rigid all-metal duct cannot be used, then flexible all-metal ducting can be used, but it will reduce the maximum ALL INSTALLATIONS, THE DRYER MUST BE CONNECTED recommended duct length.
  • Page 11 Installation Instructions / Electric Dryer www.GEAppliances.ca DRYER EXHAUST TO RIGHT, LEFT OR ADDING NEW DUCT BOTTOM CABINET FIXING HOLE WARNING - BEFORE PERFORMING PORTION “A” THIS EXHAUST INSTALLATION, BE SURE TO DISCONNECT THE DRYER FROM ITS ELECTRICAL SUPPLY. PROTECT YOUR HANDS AND ARMS FROM SHARP EDGES WHEN WORKING INSIDE THE CABINET.
  • Page 12 Installation Instructions / Electric Dryer DRYER EXHAUST TO RIGHT, LEFT OR SERVICING BOTTOM CABINET WARNING - LABEL ALL WIRES PRIOR • Insert the elbow through the rear opening and connect it to the TO DISCONNECTING WHEN SERVICING dryer internal duct. CONTROLS.
  • Page 13 Installation Instructions / Gas Dryer www.GEAppliances.ca WARNING! PEDESTALS FOR DRYERS (comes with individual installation instructions) FOR YOUR SAFETY: Available models: -SBSD227F Use only rigid metal or flexible metal 10 cm (4 in.) diameter -SBSD137H ductwork for exhausting to the outdoors. Never use plastic -SBSD107H or other combustible, easy-to-puncture ductwork.
  • Page 14 Installation Instructions / Gas Dryer Minimum Clearance Other Than Alcove or Closet Installation Minimum clearance to combustible surfaces and for air opening are: 0 cm (0 in.) clearance both sides and 2.5 cm (1 in.) rear. Consideration must be given to provide adequate clearance for installation and service. PREPARING FOR INSTALLATION Tilt the dryer sideways and remove the foam...
  • Page 15 Installation Instructions / Gas Dryer www.GEAppliances.ca RECONNECTING GAS Listed connector ANSIZ21.24 / CSA 6.10 FLARE APPLY PIPE COMPOUND TO ALL MALE THREADS. ADAPTER 0.3 cm (1/8") NPT PIPE PLUG FOR NEW METAL CHECKING GAS FLEXIBLE GAS LINE INLET PRESSURE CONNECTOR SHUT-OFF ADAPTER VALVE...
  • Page 16 Installation Instructions / Gas Dryer ELECTRICAL CONNECTION EXHAUST INFORMATION INFORMATION WARNING - USE ONLY METAL 10 cm (4in.) DUCT. DO NOT USE DUCT LONGER THAN WARNING - TO REDUCE THE RISK OF FIRE, SPECIFIED IN THE EXHAUST LENGTH TABLE. ELECTRICAL SHOCK AND PERSONAL INJURY: Using exhaust longer than specified length will: DO NOT USE AN EXTENSION CORD OR AN •...
  • Page 17 Installation Instructions / Gas Dryer www.GEAppliances.ca EXHAUST CONNECTION WARNING - TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY: This dryer must be exhausted to the outdoors. • Use only metal duct. • Do not terminate exhaust in a chimney, any gas ELBOW HIGHLY RECOMMENDED vent, under an enclosed floor (crawl space), or into...
  • Page 18 Installation Instructions / Gas Dryer USING FLEXIBLE METAL DUCTS EXHAUSTING A CLOTHES DRYER PRODUCES COMBUSTIBLE LINT. FOR If rigid all-metal duct cannot be used, then flexible all-metal venting can be used, but it will reduce the maximum ALL INSTALLATIONS, THE DRYER MUST BE CONNECTED recommended duct length.
  • Page 19 Installation Instructions / Gas Dryer www.GEAppliances.ca DRYER EXHAUST TO LEFT OR BOTTOM ADDING NEW DUCT CABINET FIXING HOLE WARNING - PROTECT YOUR PORTION “A” HANDS AND ARMS FROM SHARP EDGES WHEN WORKING INSIDE THE CABINET. REMOVE RIGHT OR SCREW LEFT SIDE AND SAVE.
  • Page 20 Installation Instructions / Gas Dryer ADDING ELBOW FOR EXHAUST RESIDENTIAL GARAGE INSTALLATION THROUGH BOTTOM OF CABINET Dryers installed in residential garages must be • Insert the elbow through the rear opening and connect it to the elevated 18 inches (46 cm) above the floor. dryer internal duct.

  • Page 21: Control Panels

    About the dryer control panel. WARNING! To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. Throughout this manual, features and appearance may vary from your model. You can locate your model number at the top inside of the door opening.
  • Page 22 About the dryer control panel. www.GEAppliances.ca Power Press to “wake up” the display. If the display is active, press to put the dryer in the standby mode. NOTE: Pressing Power does not disconnect the appliance from the power supply. Dry Cycles The dry cycle controls the length and tumble speed of the drying process.
  • Page 23 Sensor Dry “Level” The sensor continuously monitors the amount of moisture in the load. When the moisture in your clothes reaches your selected dry level, the dryer will stop. Note: Sensor dry “Level” only works for Mixed Loads,Cottons, Bulky Bedding, Easy Care, Delicates and Speed Dry.

  • Page 24: Cycle Options

    About cycle options. NOTE: Not all features are available on all dryer models. www.GEAppliances.ca Extended Tumble Ext Tumble The extended tumble time does not get Minimizes wrinkles by adding approximately added to the cycle time on the display 60 minutes of no-heat tumbling after clothes are dry.

  • Page 25: Dryer Features

    About cycle options. NOTE: Not all features are available on all dryer models. Lock You can lock the controls to prevent any To lock the dryer, press and hold the lock icon selections from being made. You can also lock for 3 seconds.

  • Page 26: Reversing The Door Swing

    Reversing the door swing. www.GEAppliances.ca IMPORTANT: Once you begin, do not move IMPORTANT NOTES: the cabinet until door-swing reversal is  Read the instructions all the way completed. through before starting. These instructions are for changing the  Handle parts carefully to avoid hinges from the right side to the left scratching paint.
  • Page 27 Reversing the door swing. STEP-BY-STEP INSTRUCTIONS (cont.) Remove Door Assembly 2. Open the door to approximately 130 degrees. 3. Remove the 4 screws starting from the bottom to the top. Make sure the door is supported while removing the screws. Remove Top Screw 4.
  • Page 28 www.GEAppliances.ca STEP-BY-STEP INSTRUCTIONS (cont.) Reinstall Hinge Assembly 7. Install the hinge assembly in the opposite side of the door as shown. Push the hinge assembly in place until the hinge holes align with the door holes. Machine screws 8. Hold the hinge and door on their side with one hand and fasten the 4 machine screws as shown.
  • Page 29 Reversing the door swing. STEP-BY-STEP INSTRUCTIONS (cont.) Outer Door Reassemble Door Assembly IMPORTANT: Make sure there is no dirt or any other foreign material in between the window panes. c i t . r o part of the outer door is opposite the hinge as shown. Inner Door 12.

  • Page 30: The Dryer

    Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce Fabric Conditioner Dryer Sheets ® have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions.
  • Page 31 The stainless steel used to make the dryer drum provides the highest reliability available in a GE dryer. If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode.

  • Page 32: Venting The Dryer

    Venting the dryer. www.GEAppliances.ca For the best drying performance, the dryer needs to be properly vented. The dryer will use more energy and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the Installation Instructions. ...

  • Page 33: Connecting Inlet Hoses

    Connecting Inlet Hoses. To produce steam, the dryer must connect to the cold water supply. Since the washer must also connect to the cold water, a “Y” connector is inserted to allow both inlet hoses to make that connection at the same time. NOTE: Use the new inlet hoses provided;...

  • Page 34: Stacking

    Stacking. www.GEAppliances.ca BEFORE YOU BEGIN Read these instructions completely and carefully.  IMPORTANT: Save these instructions for local  Note to Consumer – Keep these instructions for electrical inspector’s use. future reference.  IMPORTANT: Observe all governing codes and  Installation must be performed by a qualified ordinances.
  • Page 35 Stacking. KIT CONTENTS (optional kit GE FL STACK) Right Hand Bracket 4 #12 x 1” Screws 4 Rubber Pads Left Hand Bracket 4 #8 x 1/2” Screws TOOLS YOU WILL NEED Phillips Screwdriver Gloves Pliers Open-Ended Wrench Level INSTALLATION PREPARATION Remove the packaging.
  • Page 36 www.GEAppliances.ca INSTALLING THE STACK BRACKET KIT 1. Remove the Dryer Leveling Legs A. Carefully lay the dryer on its side. Use the packing material so you don’t scratch the finish on the dryer. B. Use an open-end wrench or pliers to remove the dryer leveling legs.
  • Page 37 Stacking. INSTALLING THE STACK BRACKET KIT (cont.) 4. Prepare the Washer and Dryer A. Place the washer in the approximate C. Reverse dryer door swing if desired. location. See dryer Installation Instructions for details. B. Make sure the washer is level. Refer to washer Installation NOTE: The washer door swing is not Instructions for details.

  • Page 38: Troubleshooting Tips

    Before you call for service… www.GEAppliances.ca Troubleshooting Tips Save time and money! Review the charts on the following pages, or visit www.GEAppliances.ca. You may not need to call for service. PROBLEM Possible Causes What To Do Dryer shakes or Some shaking/noise is normal. •...
  • Page 39 Before you call for service… PROBLEM Possible Causes What To Do Time Remaining The estimated time may change • This is normal. jumped to a when a smaller load than usual lower number is drying Cannot make a The DRYNESS Level, TEMP •...
  • Page 40 www.GEAppliances.ca PROBLEM Possible Causes What To Do Clothes shrink Some fabrics will naturally shrink • To avoid shrinkage, follow garment care labels exactly. when washed. Others can be • Some items may be pressed back into shape after drying. safely washed, but will shrink •...
  • Page 41 Cannot see steam at any The steam nozzle might be • Call 800.GE.CARES to order nozzle replacement kit WE25M71 or to request a service technician to replace this for you. time during the cycle clogged with debris from your...
  • Page 42 Notes. www.GEAppliances.ca...

  • Page 43: Warranty

    This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service.
  • Page 44 One Year Any part of the dryer which fails due to a defect in materials or workmanship. During this limited one-year warranty, GE will also provide, free of charge, all labor and related service costs From the date of the to replace the defective part.

  • Page 45: Consumer Support

    Contact Us www.GEAppliances.com In the U.S.: If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations a i l...

Table of Contents