CONTENTS GENERAL POWER TOOL SAFETY WARNINGS GENERAL SAFETY WARNINGS FOR BATTERY CHARGER COMPONENT LIST ACCESSORIES SYMBOLS TECHNICAL DATA NOISE INFORMATION OPERATING INSTRUCTIONS WORKING HINTS FOR YOUR ANGLE GRINDER MAINTENANCE TROUBLESHOOTING ENVIRONMENTAL PROTECTION DECLARATION OF CONFORMITY...
ORIGINAL INSTRUCTION GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all 3. PERSONAL SAFETY instructions. Failure to follow the warnings and a) Stay alert, watch what you are doing and use instructions may result in electric shock, fire and/or serious common sense when operating a power tool.
Page 4
GENERAL POWER TOOL SAFETY WARNINGS of battery pack may create a risk of fire when used with d) Store idle power tools out of the reach of children another battery pack. and do not allow persons unfamiliar with the power tool or these instructions to operate the b) Use power tools only with specifically designated power tool.
Page 5
h) Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations .
Page 6
ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDING AND CUTTING-OFF OPERATIONS Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations: a) Use only disc types that are recommended for your power tool and the specific guard designed for the selected disc. Discs for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The grinding surface of centre depressed discs must be mounted below the plane of the guard lip.
Page 7
SAFETY WARNINGS FOR BATTERY PACK a) Do not dismantle, open or shred cells or battery pack. b) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by conductive materials. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.
GENERAL SAFETY WARNINGS FOR BATTERY CHARGER WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
SYMBOLS Li-ion battery. This product has been marked To reduce the risk of injury, read all of this with a symbol relating to ‘separate collection’ instruction manual for all battery packs and battery pack. It Li-Ion will then be recycled or dismantled in order Warning to reduce the impact on the environment.
TECHNICAL DATA Voltage Rated speed 8800/min Disc size 115 mm Disc bore 22.2 mm Spindle thread Machine weight (With battery pack) 1.83 kg Charger Protection class Charging time 2 hrs Charger Input 100-240V~50/60Hz,55W Charger Output 20VDC 2.0A Battery capacity 4.0Ah Li-ion battery Battery Model ABP1840HW Charger Model...
Page 12
VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN 60745: Vibration emission value a = 4.381m/s² h.AG Surface grinding or abrasive cutting off Uncertainty K = 1.5 m/s² The declared vibration total value may be used for comparing one tool with another, and may also be used in a preliminary assessment of exposure.
OPERATING INSTRUCTIONS NOTE: Before using the tool, read the instruction book carefully. Intended Use The machine is intended for cutting, roughing and brushing metal and stone materials without using water. For cutting metal, a special protection guard for cutting (accessory) must be used. BEFORE PUTTING INTO OPERATION A) CHARGING THE BATTERY The battery supplied is partially charged.
Page 14
D) HOW TO CHARGE YOUR BATTERY PACK (See Fig. A3) CHARGING PROCEDURE 1) Plug the charger into an appropriate outlet. The light will be green. 2) Slide the battery pack into the charger, the light will turn to red to indicate the charging process has started. 3) When charging is completed, the light will turn to green.
Page 15
3. INSTALLING AND ADJUSTING THE DISC GUARD (See Fig. C1, C2, C3) For work with grinding or cutting discs, the disc guard must be mounted. Disc Guard for Grinding (7) The coded projection on the disc guard (7) ensures that only a guard that fits the machine type can be mounted.
Page 16
Press in the spindle lock button (2) and rotate the spindle by hand until it is locked. Keeping the lock button pressed in, tighten the outer flange (11) with the spanner (9) provided. (See Fig. D3) NOTE: After mounting the grinder tool and before switch on, check that the grinding tool is correctly mounted and that it can be turn freely, make sure that the grinding tool does not graze against the protecting guard or other parts.
8. CUTTING (See Fig. G) WARNING! For cutting metal, always work with the disc guard for cutting (not supplied). When cutting, do not press, tilt or oscillate the tool. Work with moderate feed, adapted to the material being cut. Do not reduce the speed of running down cutting discs by applying sideward pressure.
MAINTENANCE Your tool requires no additional lubrication or maintenance. There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust.
DECLARATION OF CONFORMITY Wickes Building Supplies Limited Declare that this product: CORDLESS ANGLE GRINDER Description and SKU code: 223736 Complies with the following Directives and Regulations: 2006/42/EC, Machinery Directive 2014/30/EU, Electromagnetic Compatibility Directive 2011/65/EU & (EU)2015/863 (RoHS),Restriction of Hazardous Substances Directive...